SOUNDTUBE CM62-BGM In Ceiling Speaker User Guide

June 16, 2024
SOUNDTUBE

soundtube-logo

SOUNDTUBE CM62-BGM In Ceiling Speaker

SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker

Install Instructions For:

  • CM42-EZs-II-WH, CM42-EZs-II-BK, CM62-EZ-II-WH, CM62-EZ-II-BK, CM62-EZs-II-WH, CM62-EZs-II-BK, CM82-EZ-II-WH, CM82-EZ-II-BK,
  • CM82-EZs-II-WH, CM82-EZs-II-BK, CM82-EZ-FS-WH, CM82-EZ-FS-BK, CM82-EZs-FS-WH, CM82-EZs-FS-BK, CM89-EZ-WH, CM89-EZ-BK,
  • CM52-BGM-WH, CM52-BGM-BK, CM52s-BGM-WH, CM52s-BGM-BK, CM62-BGM-WH, CM62-BGM-BK, CM82-BGM-WH and CM82-BGM-BK

Ceiling thickness tolerancesSOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-
FIG-1

Box contents

  • 1 Speaker
  • 1 Flexible conduit clamp
  • 1 Cover plate
  • 1 Grille
  • 1 Installation aid/paint mask

Warning: SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
Warning : Do not spec or install speaker near support beam, ventilation duct or other structure that may interfere with speaker function or dispersion.

Droptile Ceiling Install Instructions For:

  • CM42-EZs-II-WH, CM42-EZs-II-BK, CM62-EZ-II-WH, CM62-EZ-II-BK, CM62-EZs-II-WH, CM62-EZs-II-BK, CM82-EZ-II-WH, CM82-EZ-II-BK,
  • CM82-EZs-II-WH, CM82-EZs-II-BK, CM82-EZ-FS-WH, CM82-EZ-FS-BK, CM82-EZs-FS-WH, CM82-EZs-FS-BK, CM89-EZ-WH, CM89-EZ-BK,
  • CM52-BGM-WH, CM52-BGM-BK, CM52s-BGM-WH, CM52s-BGM-BK, CM62-BGM-WH, CM62-BGM-BK, CM82-BGM-WH and CM82-BGM-BK
  1. Unpack speaker & set aside grille assembly.
  2. Use included tile bridge to mark cutout in tile.
  3. Use Rotozip or other tool to cut hole.
    • Hole Diameters
    • CM42-EZs-II
    • 165.1 mm (6.50 in)
    • All other CMEZ, FS and BGM models 266.7 mm (10.50 in)
  4. Run signal wires through conduit connector, then through cover plate. Connect to ceramic terminal strip. Two + and two – connectors are provided for daisy chaining. SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-2
  5. Tighten screw on terminal plate, and push conduit connector into knock out.
  6. Insert speaker into mounting hole with installation aid in place. Screw down both bolts on the baffle face to actuate the mounting wings. Firmly secure both bolts – do not over-tighten.
  7. If required, a sheet-metal tab located on the rear panel of the speaker serves as a secondary point of attachment (cable not included).
  8. Once all painting and finish work is completed, remove the paint mask.SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-3
  9. Select the tap position by adjusting rotary switch to desired high impedance value or voice coil direct mode.
  10. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-4
  11. Press grille into place.
  12. Done!

Sheetrock Ceiling Install Instructions For:

  • CM42-EZs-II-WH, CM42-EZs-II-BK, CM62-EZ-II-WH, CM62-EZ-II-BK, CM62-EZs-II-WH, CM62-EZs-II-BK, CM82-EZ-II-WH, CM82-EZ-II-BK,
  • CM82-EZs-II-WH, CM82-EZs-II-BK, CM82-EZ-FS-WH, CM82-EZ-FS-BK, CM82-EZs-FS-WH, CM82-EZs-FS-BK, CM89-EZ-WH, CM89-EZ-BK,
  • CM52-BGM-WH, CM52-BGM-BK, CM52s-BGM-WH, CM52s-BGM-BK, CM62-BGM-WH, CM62-BGM-BK, CM82-BGM-WH and CM82-BGM-BK
  1. Unpack speaker & set aside grille assembly.
  2. Use included tile bridge to mark cutout in sheetrock
  3. Use Rotozip or other tool to cut hole.\
    • Hole Diameters
    • CM42-EZs-II
    • 165.1 mm (6.50 in)
    • All other CMEZ, FS and BGM models 266.7 mm (10.50 in)
  4. Run signal wires through conduit connector, then through cover plate. Connect to ceramic terminal strip. Two + and two – connectors are provided for daisy chaining.SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-5
  5. Tighten screw on terminal plate, and push conduit connector into knockout.
  6. If required, a sheet-metal tab located on the rear panel of the speaker serves as a secondary point of attachment (cable not included).
  7. Insert speaker into mounting hole with installation aid in place. Screw down both bolts on the baffle face to actuate the mounting wings. Firmly secure both bolts – do not over-tighten.
  8. Once all painting and finish work is completed, remove the paint mask.SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-6
  9. Select the tap position by adjusting rotary switch to desired high impedance value or voice coil direct mode.
  10. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-7
  11. Press grille into place.
  12. Done!

Pre-Construction Bracket Instructions For:

  • CM42-EZs-II-WH, CM42-EZs-II-BK, CM62-EZ-II-WH, CM62-EZ-II-BK, CM62-EZs-II-WH, CM62-EZs-II-BK, CM82-EZ-II-WH, CM82-EZ-II-BK,
  • CM82-EZs-II-WH, CM82-EZs-II-BK, CM82-EZ-FS-WH, CM82-EZ-FS-BK, CM82-EZs-FS-WH, CM82-EZs-FS-BK, CM89-EZ-WH, CM89-EZ-BK,
  • CM52-BGM-WH, CM52-BGM-BK, CM52s-BGM-WH, CM52s-BGM-BK, CM62-BGM-WH, CM62-BGM-BK, CM82-BGM-WH and CM82-BGM-BK
  1. Nail or screw bracket to joists. Secure conduit/signal wire away from hole in bracket.
  2. Complete Finish work.
  3. Use Rotozip or other tool to cut hole.
    • Hole Diameters
    • CM42-EZs-II
    • 165.1 mm (6.50 in)
    • All other CMEZ, FS and BGM models 266.7 mm (10.50 in)
  4. Run signal wires through conduit connector, then through cover plate. Connect to ceramic terminal strip. Two + and two – connectors are provided for daisy chaining.SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-8
  5. Tighten screw on terminal plate, and push conduit connector into knockout.
  6. If required, a sheet-metal tab located on the rear panel of the speaker serves as a secondary point of attachment (cable not included).
  7. Insert speaker into mounting hole with installation aid in place. Screw down both bolts on the baffle face to actuate the mounting wings. Firmly secure both bolts – do not over-tighten.
  8. Once all painting and finish work is completed, remove the paint mask.SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-9
  9. Select the tap position by adjusting rotary switch to desired high impedance value or voice coil direct mode.
  10. Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
  11. Press grille into place.
  12. Done!SOUNDTUBE-CM62-BGM-In-Ceiling-Speaker-FIG-10

EQ settings required for the EN54-24 specific installations

Model EQ-1 BANDWIDTH EQ-2 BANDWIDTH
CM62-BGM -3dB @ 125Hz .5 Octave -3dB @ 175Hz 1.0 Octave
CM62- EZ-II -6dB @ 200Hz 1.0 Octave +2dB @ 4800Hz 0.7 Octave
CM62-EZs-II -6dB @ 200Hz 1.0 Octave +3dB @ 4800Hz 0.7 Octave
CM42- EZs-II -4dB @ 200Hz 1.0 Octave

SoundTube Entertainment Inc
6430 North Business Park Loop Rd.
Park City, UT 84098
0359-CPR-00442
EN54-24:2008
CM62-BGM-WH, CM62-BGM-BK, CM62-EZs-II-WH, CM62-EZs-II-BK,
CM62-EZ-II-WH, CM62-EZ-II-BK, CM42-EZs-II-WH, CM42-EZs-II-BK

Essential characteristics Performance
Scattering (frequency range/sensitivity) Passed
Nominal impedance Passed
Horizontal and vertical dispersion angle p Passed
Maximum sound pressure level Passed
Nominal noise performance (durability) Passed
Dry heat (operating) Passed
Dry heat (endurance) N/A
Cold (in operation) Passed
Damp heat, cyclic (operating) Passed
Damp heat, steady state (endurance) Passed
Damp heat, cyclic (fatigue test) N/A
Sulfur dioxide (SO2) corrosion (endurance) Passed
Shock (operating) Passed
Impact (operating) Passed
Sinusoidal vibration (operating) Passed
Vibration, sinusoidal (endurance) Passed
Enclosure testing Passed

Document Issue Date: 12-4-14
Document Reference Number: CMEZ0039
Document Revision: 02-04-2015 Rev 2.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SOUNDTUBE User Manuals

Related Manuals