Surenoo STP0177F-128160 Series TFT Touch LCD Panel User Manual

Surenoo STP0177F-128160 Series TFT Touch LCD Panel

General Description

M ODEL NO

| STP0177F-128160
---|---
Display Mode

| ****

Transmissive

Display Format

| ****

Graphic 128RGB*160 Dot-matrix

Input Data

| ****

SPI-4wire interface

Viewing Direction

| ****

12 o’clock

Drive

| ****

ST7735S

Mechanical Specification

Dimensional outline

| 34.00(W)45.83(H)2.40max(T)

(FPC not include)

| mm
Dimensional outline

| 34.00(W)45.83(H)3.65max(T)

(FPC not include)

| mm
Resolution

| 128RGB*160| dots
LCD Active area

| 28.03 (W)*35.04 (H)| mm
Pixel size

| 0.219(W)*0.219(H)| mm

Mechanical Dimension

Electrical Maximum Ratings

Item

| Symbol

| Min

| Max

| Unit

| Note

---|---|---|---|---|---
Supply voltage （ IOVCC ）

| V| 1.8| 3.3| V|
Supply voltage （ VCC ）

| V| 2.8| 3.3| V|
Operating temperature 工

| T OPR| -20| 70| ℃|
Storage temperature

| T STR| -30| 80| ℃|

Backlight Characteristic

Item

| Symbol

| Min

| Typical

| Max

| Unit
---|---|---|---|---|---
LED module Forward voltage

| V LED| 2 ． 9| 3.1| 3.3| V
LED module current

| I LED| –| 30| –| mA
LCD Surface Luminance

| L S| 150| 180| –| C d / m 2
LCM Surface brightness uniform

| L D| 80| –| –| %

Module Function Description

Display screen

PIN No.

| Symbol

| D escription

| Notes

备 注

---|---|---|---
1| NC| No connection

|
2| GND| Ground

|
3| LED-| Cathode of Backlight

|
4| LED+| Anode of Backlight

2.9-3.3

|
5| GND| Ground

|
6| /RESET| LCM Reset pin.Signal is active low

|

7

| ****

A0

| Register select pin）

RS=’0’: Display data.（RS=’0’:） RS=’1’: Display data.（RS=’1’:

|
8| SDA| Serial data input / output.

|
9| SCK| Serial clock pin.

(

|
10| VCC| Power supply for LCM

2.8-3.3V)

|
11| IOVCC| Power supply for LCM

1.8-3.3V)

|
12| CS| Chip select pin (“Low” enable)

|
13| GND| Ground

|
14| NC| No connection

|

（Touch panel

PIN No.

| Symbol

| D escription

| Notes

---|---|---|---
1| YU| Touch panel control pin

|
2| XL| Touch panel control pin

|
3| YD| Touch panel control pin

|
4| XR| Touch panel control pin

|

Z180ST029 v0.0

Response time&Contrast ratio

I tem

| S ymbol

| C ondition

| R emark| Unit

---|---|---|---|---
M in.

| T yp.

| M ax.

Response time

| Tr+Tf| θ=0°| –| 30| 60| ms
Contrast ratio

| CR| θ=0°| 200| 300| –|

I tem

| S ymbol

| C ondition

| R emark| Unit

---|---|---|---|---
M in.

| T yp.

| M ax.

Viewing angle

| Top

| CR≥10

| 20| 30| –| ****

Deg.

Bottom

| CR≥10

| 40| 45| –
Left

| CR≥10

| 40| 45| –
Right

| CR≥10

| 40| 45| –

Reliability Trial

N O.

| I TEM

| C ONDITION

| C RITERION

---|---|---|---
1| High Temperature Non-Operating Test| 80℃120Hrs| No Defect Of
 | Operational
2| Low Temperature Non-Operating Test| -30℃120Hrs| Function In Room
 | Temperature Are
3| High Temperature/Humidity Non Operating Test| 60℃90%RH120Hrs| Allowable
 |
4| High Temperature Operating Test| 70℃72Hrs|
 |
5| Low Temperature Operating Test| -20℃72Hrs|
 |
6| Thermal Shock Test| -20 ℃ (30Min) n 70 ℃|
 | (30Min) *10CYCLES|

inspection standards

Glass defect

1

| Dimension Unconformity

(Major defect)

| By Engineering Drawing|

2

| Cracks

(Major defect)

| 1.        Linear cracks panel

【Reject】

2.        Nonlinear crack contrast by limited sample

| ****

3

| Glass extrude the conductive area

(minor defect)

| a: disregards and no influence assemblage.

1)       b≤1/3Pin width(non bonding area)

【Accept】

2. bonding area≤0.5mm

【Accept】

|

A: Length, b: Width

4

| Pin-side ,conductive area damaged

(minor defect)

| (a c: disregards)

b≤1/3of effective length for bonding electrode

【Accept】

| a: length, b: Width, c: Thickness

5

| Pin-side,non-conductive area damaged

(minor defect)

| 1)  Damage area don’t touch the ITO (Inclueling contraposition mark, except scribing mark)

【Accept】

2)  C<T b≦BM1/3of width

| a: Length, b: Width c:

Thickness

 |  | 【Accept】

3)  c=T

b not touch the seal glue

【Accept】

4)  a disregards

| ****
---|---|---|---

6

| Non-pin-side damage

(minor defect)

| c<T

1)b exceeds 1/3Bm

【Reject】

c=T

b not touch the seal glue

【Reject】

| c: Thickness b: width of

damage

LCD appearance defect(View area)

1

| ****

Fiber、glass cratch、polarizer scratch/folded

(minor defect)

| Specification| Allowable| note1:L: Length, W: Width note2: disregard if out of AA

W≦0.03mm| disregard
0.03mm<W≦0.05mm;

L≦3.0mm

| 2
0.05mm<W≦0.1mm;

L≦3.0mm

| 1
W>0.1mm;L>3.0mm| 0

2

| Polarizer bubble、 concave and convex

(minor defect)

| φ≦0.2mm| disregard| note1: φ=(L+W)/2,L:Length,

W :Width

note2:disregard if out of AA

0.2mm<φ≦0.3mm| 2
0.3mm<φ≦0.5mm| 1
0.5mm<φ| 0

3

| ****

Black dots、dirty dots、 impurities、eye winker

(minor defect)

| φ≦0.15mm| disregard| note2:disregard if out of AA

0.15mm <φ≦0.25mm| 2
0.25mm<φ≦0.3mm| 1
0.3mm<φ| 0

4

| ****

Polarizer prick

(minor defect)

| φ≦0.1mm| disregard| note1: φ=(L+W)/2,L=Length,

W=Width

note2:the distance between two dots>5mm

0.1mm<φ≦0.25mm| 3
φ>0.25mm| 0

Package Method

Shenzhen Surenoo Technology Co.,Ltd. www.surenoo.com
Skype: Surenoo365

References

• Surenoo Tech: Professional LCD Module Supplier Since 2005

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>