MIVARDI Carp Scout XL Remote-Controlled Bait Boat with GPS and Fish Finder Instruction Manual

This instruction manual is intended for models
Remote-controlled bait boat with GPS and fish finder
Ferngesteuertes Futterboot mit GPS und Echolot
Carp Scout XL / Li / LA
CARP SCOUT

Carp Scout XL Remote-Controlled Bait Boat with GPS and Fish Finder

The company MIVARDI s.r.o. hereby declares that the product is in compliance with Directive 1999/5 / EC.
Important: Before using the product, read this manual carefully. It will help you to set up all functions and use them correctly when operating the boat.
Without the correct settings, the boat may not work correctly !!!

BOAT

Main functions and specifications of the boat

1. Fully digital duplex remote control at 2.4 GHz
2. Remote controller with a built-in antenna and LCD display showing the status of the boat and all its functions
3. Integrated digital compass allows an automatic sailing in the selected direction
4. GPS navigation system with 31 memory positions to save the destination points
5. Built-in echo sounder, displaying information on bottom relief, water temperature and fish occurrence on the controller display
6. Automatic return of the boat to the starting point in case of failure of the remote control, or loss of connection between the boat and the control
7. Automatic control of the key functions. The boat performs a self-check and in case of a problem, an icon with the specification of the problem (compass, GPS, echo sounder) is displayed on the controller‘s display.
8. Possibility to update the boat firmware and driver by the service centre

cruise control modes

MANU
(manual sailing mode)| ou control the navigation direction manually with the joystick
---|---
AUTO
(automatic sailing)| The electronic compass controls and keeps the sailing direction. You still can use the joystick to adjust the sailing direction manually.
GPS
(sailing with GPS navigation)| The boat automatically sails to the selected destination point using GPS
navigation and the electronic compass.

FISH FINDER

Main functions:

• Water temperature measurement
• Measurement of the water depth (maximum depth range up to 30 m)
• Automatic switching of 4 depth ranges: 2-5 m, 5-15 m, 15-20 m, and 20-30 m
• Three sizes of icons showing the detected fish: large, medium and small
• Fish detection in three sensitivity levels: C1 / C2 / C3 (from lowest to highest sensitivity)
• Display of the profile and hardness of the bottom
  Notice: The echo sounder only works and shows correct output if the boat is in the water. The echo sounder works reliably and correctly measures depths in water deeper than 2 m.

GPS NAVIGATIoN

GPS functions

• You can set and save 31 different GPS points (1 starting „HOME“ point and 30 destination points)
• The boat shows the distance to the „HOME“ point and to the selected destination point
• The boat can automatically sail to selected destination point using GPS navigation
• The boat automatically returns to the starting point if the connection with the remote control is lost or (Only if the „HOME“ point has been correctly stored)
• The boat‘s front and rear lights flash and the remote control beeps when the boat reaches its destination.

Using the GPS navigation:

• Switch on the boat and wait about 3 minutes before you start using the GPS system. During this time the maximum number of GPS satellites are being searched. This ensures a more accurate determination of the position of the boat and thus higher accuracy of navigation in GPS mode. At least five GPS satellites are required to get the correct function of the GPS navigation.
• Press the GPS button to enter the GPS navigation menu. There are 31 positions available (1 starting point „HOME“ and 30 destination points, marked with numbers). The GPS coordinates of the starting point and the current GPS coordinates of the boat are also displayed.
• Use the + / – buttons to select the appropriate memory position. The currently selected position flashes.
• Shortly press the SET button to save the current position of the boat to the selected memory position. After saving, the icon of the selected position will get a black background.
• To clear the memory position, use the + / – buttons to select the appropriate position you want to delete. Then press the SET button to clear the position. The black background of the icon will be removed.
• To sail to a selected destination point, first select this position with the + / – buttons. Then confirm the sailing to this point pressing the Go button. Press Go again to return to the home screen.
• You can exit the GPS menu at any time by pressing the ESc key.

CHARGING

The charger is equipped with LED charging indicators. A red light means the charging process in progress. When charging is complete, the red light turns green, indicating full charge.
charging the boat battery:
Remove the batteries from the boat. Connect the supplied adaptor to both batteries and to the charger. Then connect the charger to the 230V power socket.
Attention! Always use the charger with 2 batteries connected. Never charge only one battery!
charging the remote controller:
The RC battery is stored inside the remote controller and is completely maintenance-free. To charge the battery, connect the charger‘s connector to the USB port on the RC and then connect the charger to the power supply. The charge status is indicated on the RC display.

SAFETY INSTRUCTIONS AND WARNINGS

• The antenna is a good conductor of electromagnetic waves and electrostatic discharges, so never use the boat during a storm.
• It is dangerous to use the remote control in areas where explosive materials are used or stored.
• The electronic compass is highly sensitive to external influences. Avoid using it near high voltage lines, as well as in areas with strong magnetic fields or mining industries.
• Please make sure that the bait hopper door magnets are clean. In case of dirt with sand, mud or other dirt, clean the magnet and the metal plate on the door so that the hopper switch can work properly.
• NEVER disassemble the boat or remote control yourself. In case of any malfunction you should always contact your dealer or authorized service centre.
• opening the body of the remote control or the body of the boat means immediate loss of warranty !!!
  The seller warns the buyer that the warranty does not apply to wear and tear of the goods caused by its normal use. (The length of the warranty period on the battery is therefore not the same as the life of the battery, as the loss of capacity is due to normal wear and tear when using the battery.)

TECHNICAL SPECIFICATION

GI’S
Accuracy| < 3 m| < 3 m
Number of destination points| 30| 30
Automatic return in case of control failure / signal loss| •| •
Fish finder
Audible signal when a fish is detected| •| •
Depth measurement| •| •
Bottom relief| •| •
Depth measurement range| 2-30 m (4 depth levels)| 2-30 m (4 depth levels)
Sensitivity steps| C1, C2, C3| C1, C2, C3
Approximate battery life
Lead acid batteries 10Ah| 60 — 80 min| 60 — 80 min
Lithium batteries 10Ah| 75 — 90 min| 75 — 90 min
Lithium batteries 20Ah| 120 —180 min| 120 —180 min

PACKAGE CONTENTS

| Name| Qty
---|---|---
1| Bait boat| 1
2| Remote controller with a built-in battery| 1
3| Boat batteries charger| 1
4| RC charger| 1
5| Charging splitter| 1
6| Boat battery| 2

REMOTE CONTROLLER

The all-in-one remote controller was developed exclusively to control the Carp Scout boats. The device is equipped with a large LCD display that shows all sailing and the boat status details. Real-time two-way data transfer increases user comfort.

Rc controls:

1. Main switch / confirmation of menu selection
   Press for 3 seconds to turn the RC on / off. In the main menu, use this button to confirm the selected setting.

2.  Menu navigation buttons

3. Menu navigation buttons

4. LcD display backlight Press to turn the backlight on / off. Hold down the button to adjust the backlight intensity.

5. Activation / deactivation of the audible warning signals Signals are provided when: the batteries are low, the bait hopper is opened, the rig hooks are released, the destination point is reached in GPS navigation mode, the signal is lost.

6. GPS Press the button to switch between the main screen and the GPS menu.

7. AUTo mode Press the button to activate the automatic sailing mode. After switching on the AUTO mode, the boat maintains its current sailing direction. In AUTO mode, you can use the joystick to adjust the sailing direction.

8. boat lights Use this button to turn on / off the boat lights.

9. Rig releasing button Press the rig releasing button to open the left rig holder. Press it again to open the right rig holder. Releasing of the rig (opening the rig holder) is confirmed by an audible signal on the remote controller and by the flashing lights on the boat. Then the empty rig holder is shown in the symbolic drawing of the boat on the display. By pressing the rig release button for the third time, you reset the displayed status of the rig holders. When the rig holder on the boat releases your rig then it automatically comes back come back to the starting position within one or two seconds.

10.  bait hopper button
    Press the bait hopper button to open the left bait hopper. Press again to open the right hopper. The opening of each hopper is confirmed by an audible signal on the controller and by the flashing lights on the boat. Then the empty bait hopper is shown in the symbolic drawing of the boat on the display. By pressing the bait hopper button for the third time, you reset the displayed status of the bait hoppers. The door of the bait hoppers must be always closed manually.

11. SET
    This button is used to save the current location of the boat to the selected memory position in the GPS menu or to delete a saved location from the selected memory position.

12. ESc Press this button to leave the GPS menu.

13. Tlačítka + a – Use these buttons to select the memory position in the GPS menu.

14. Tlačítka + a – Use these buttons to select the memory position in the GPS menu.

15.  Go Press this button to start an automatic sailing with GPS navigation to the destination point, stored under the currently selected memory position in the GPS
    menu. During automatic GPS navigation, you can press GO to interrupt automatic navigation and return to manual driving.

RC MENU AND USAGE INSTRUCTIONS

Main menu of the Rc:

• Use the “ ” or “ ****” button to enter the menu and then scroll through the items and select them.
• Activate the currently selected menu item by pressing the power button. This will trigger a specific action or enter a submenu.
• Navigate in the submenu with the “ ” or “ ****” buttons.
• Press the power button to confirm the selected submenu option.
• After confirmation, the selection is saved and the main menu is displayed.

Main screen of the remote controller:

1. Signal monitor
2. Water depth
3. Water temperature
4. RC battery status
5. Boat battery status
6. Number of available GPS satellites
7. Detected fish
8. Bottom contour
9. Symbolic drawing of the boat (It shows the status of the bait hoppers, rig holders and boat lights)
10. Sailing direction
11. Currently used sailing mode (STOP / MANUAL / AUTO / GPS)
12. Current distance between the boat and the saved „HOME“ point

GPS menu:

1. Memory position to save the „HOME“ destination point
2. Memory positions for destination points
3. GPS coordinates of the boat
4. GPS coordinates of the currently used destination point
5. Sailing mode (STOP / MANUAL / AUTO / GPS)
6. Distance between the boat and the „HOME“ point
7. Currently used destination point and the distance between this point and the boat

Main menu items:

CALIBRATE RC COMPASS
CALIBRATE BOAT COMPASS
FISH FINDER
BOAT BATTERY
PAIRING MODE
EXIT

Menu items and their settings:

CALIBRATE Rc COMPASS| Press the power button to enter the RC calibration mode. Press the power button again to start this calibration. Hold the RC in a horizontal position. Rotate the RC 360 ° around the vertical axis and then move the RC up and down. When the calibration is completed, the calibration mode symbol disappears from the screen.
CALIBRATE BOAT COMPASS| 1) Ride the boat a few meters far from the bank. Then activate this menu item using the main switch button to start the calibration.
2) The boat on the water automatically performs the calibration (rotates round left and right) and then it announces the completion of the calibration. Note: calibration is successful if the arrow on the Rc display (the controller must be
held horizontally) points in the same direction as the bow of the boat. otherwise, the calibration must be performed again.
FISH FINDER| Set the sensitivity from the lowest to the highest (C1, C2, C3)
BOAT BATTERY| Select your boat version (used boat batteries). You can choose from lithium and lead-acid batteries (Li / Q). Wrong setting will cause a wrong function of the battery status monitor and empty battery warning.
PAIRING MODE| This option allows to pair the boat with RC. Your boat has been paired before delivery. It is not necessary to do it again. In rare cases, a pairing error may occur, and the pairing needs to be restored. The boat must be switched off when pairing. Switch on the RC only. In the main menu, select „Pairing mode“ and enter it with power button. Then select the required channel with the arrow keys and press the power button to save it. The countdown starts on the controller. At this moment, turn on the boat. The lights will flash during the pairing. When the pairing is completed, the pairing mode remains on the display for 5 seconds and then the main menu is displayed.
EXIT| Confirm this menu item to leave the main menu.

Monitoring of key functions and fault reporting
The boat has a monitoring of the key functions. If a fault is detected, the corresponding symbol will appear on the display.
If this happens, inform your dealer about the type of error (symbol displayed).

www.mivardi.com
Producer
Mivardi, s. r. o., Tlustého 2401/4,
193 00 Praha 9, Česká republika
Tel: +420 281 921 962
Service cente
Mivardi, s. r. o., Třebovská 47, 789 85 Mohelnice
Česká republika, Tel. +420 583 431 886
e -mail:info@fish-pro.cz

  BEGIN:VCARD VERSION:3.0 ORG:Mivardi\, s. r. o.
EMAIL;TYPE=INTERNET:info@fish-pro.cz
URL:www.mivardi.cz
TEL:+420 583â431â
886 END:VCARD

References

• PRO CLIENT, s.r.o. - webové aplikace na míru
• Mivardi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>