MIVARDI M-BOAT 320 P Inflatable Boat User Guide

User guide
M ‑BOAT 320 P
With solid floor

M-BOAT 320 P Inflatable Boat

The Mivardi M ‑BOAT boats will certainly exceed your expectations with their quality and innovative features. They are an excellent helper, both for fishermen and for other fans of staying by the water. The boats are made of high ‑quality laminated and lightweight PVC made in Korea with high resistance to abrasion and mechanical damage. Thanks to the use of this quality material, the boats are very easy to handle. The boats are equipped with  valves with a safety catch for easy inflation. Of course, there are three separate inflatable chambers for crew safety. Each boat comes with a special foot  pump for quick, easy inflation and deflation of the boat, folding aluminium oars, carrying handles, a perimeter rope, variable benches, a transport bag and
a set for minor repairs.
Read this owner’s manual carefully before using the boat. Follow all safety instructions in the manual. Keep the manual in a dry and safe place. We recommend beginners to take the appropriate boating courses.

Inflatable boat Mivardi M ‑BOAT 320 P has been manufactured in accordance with the following standards and laws:
Regulation of the Government of the Czech Republic no.174/2005 Sb. and subsequent amendments, in accordance with the Act of the Czech Republic no.22/1977 Sb as amended.
ČSN EN ISO 6185‑2, category V.
Related standards: ČSN EN ISO 10087, ČSN EN ISO 10240, ISO 14945.

•  Low weight due to the use of a special layered material
• Specially shaped bow, optimised for use with electric motors
• Excellent hydrodynamics and excellent driving characteristics
• Protective side belt against abrasion
• Quick inflation and deflation
• Compact dimensions for transport
• High stability and load capacity achieved by using large diameter main floats
• You can use an internal outboard engine or electric motor thanks to the reinforced mirror mounting

Accessories

• Aluminum folding oars
• Foot pump
• Variable benches
• Carrying bag
• Minor repair kit

Technical parameters

• weight is stated including floor, benches and without oars

Dimensions

M‑BoAt accessories

Boat inflation procedure and floor installation

1.  Spread the boat on a flat surface without sharp objects.
2. Use the included foot air pump to inflate the boat.
3. Inflate the boat to approx. 50% without keel
4. Insert part of floor No. 1 into the bow of the boat.
5. Insert part of floor No. 4 into the stern of the boat.
6. Insert part of floor No. 2 to the part no.1
7. Insert part of floor No. 3 between parts 2 and 4
8. Connect the floor with the side rails at the cut.
9. Inflate the keel.
10. Insert the bench in the desired location.
11. Inflate the boat and check the valves for air leaks.
12. Always close the valves with the cover.

Notice!
The pressure in the boat’s chambers may increase due to an increase in ambient temperature, for example when the boat is pulled out of the water into  direct sunlight. Increasing the pressure above the operating pressure limit can cause damage to the boat. If necessary, reduce the pressure in the chambers  by releasing air. Check the air pressure continuously.

To deflate the boat and the floor

1. Place the boat on a flat surface without sharp objects.
2. Unscrew the caps from the valve.
3. Deflate the boat by pressing the valve.
4. Use a foot pump for complete deflating ‑ it is necessary to screw the hose into the hole of the air drain pump.
5. Remove the side rails of the floor
6. Lift to remove parts 2 and 3 of the floor and then the remaining parts
7. Roll up the boat and store it in a dry place out of direct sunlight.

Boat trip

The boat is designed for navigation on inland waterways. possibly at sea

Warning:
Before sailing, make sure that the river, water area or area in which you intend to move is not subject to any special provisions or prohibitions and orders  that must be followed. When sailing, the user of the vessel is obliged to comply with local laws, rules, ordinances and regulations on operation on the  waterway. A person under the age of 15 may not drive a motorised vessel. The boat is not intended to be towed behind a motor boat, except for emergency towing.
The boat must not be overloaded or overstressed. Secure sharp or pointed objects inside the boat so that they cannot damage the air chambers. The cargo and the persons in the boat must be evenly distributed.

On large bodies of water (sea, lakes) watch out for winds blowing from the shore and water currents! there is a risk of non ‑return! the boat must not be used in difficult conditions, such as reduced visibility (night, fog, rain)!

Boat storage

 We recommend storing the boat in an inflated state, so there is no stress on the material and joints. If you are not able to store the boat in this way, please  pay attention to the following instructions. Thoroughly clean and dry the boat before storage. If the boat has been used at sea, rinse it thoroughly with fresh water. Use environmentally friendly products for cleaning. The surface of the boat should be treated with a special UV protection agent. Remove all solid sharp parts from the boat. Store the boat packed in a protective bag in a dry place. Do not load the boat from above. When handling the  oat, do not drag it on the surface, you can pierce it in places of sharp storage or under valves. The risk of damage during handling increases at temperatures below 0° C. Protect the stored boat from rodents. The surface of the boat does not benefit from the action of solvents (petrol, toluene, etc.) and synthetic oils. During long ‑term storage, we recommend occasionally inflating the boat for 24 hours to prevent it from lying down. Careful maintenance and care will increase the life of your boat.

Boat repair

Using the included minor repair kit, you can self ‑repair minor defects:

1. Mark the damaged area and prepare a patch that exceeds the damage of min. 3 cm on all sides.
2. The surface of the patch and the glued area must be dry and clean.
3. Clean the patch and the damaged area with acetone.
4. Apply a thin layer of adhesive to both bonded surfaces.
5. After the glue has set (3‑5 minutes), apply the patch to the damaged area and press firmly, preferably with a roller on a flat surface.
6. The final strength of the joint is reached after 24 hours.
7. We recommend performing more demanding repairs in the service centre at the manufacturer or in an authorised repair shop.

Disposal of the product at the end of its service life:
Dispose of as municipal waste in a landfill. Other disposal is not permitted!
Important notice

1.  Handle the boat out of the reach of sharp objects.
2. The boat is designed for temperatures from ‑30° C to + 70° C.
3. Always wear certified life jackets when sailing.
4. Do not drive on the river during a flood, there is a risk of drowning.
5. Pay attention to water level control, dangerous currents and weather changes, be careful at sea with changes in tides.
6. Battery acids, oils and motor fuels can permanently damage the boat. Handle the engine and batteries with the utmost care to prevent leakage. There is a risk of damage to the boat and, in extreme cases, it’s sinking.
7. The user of this product must have a basic knowledge of boating skills and must be aware of the risks involved in this sport.
8. When sailing, always have the boat equipped with basic accessories ‑ oars, foot pump.
9. Do not use the boat under the influence of alcohol or addictive substances, there is a risk of drowning!
10. Never overload the boat with an excessive load or more people than it is intended for, there is a risk of tipping over.
11. Use the boat in accordance with the information on the boat’s  label. Never exceed these limits, there is a  risk of damage to the boat and endangering the safety of the crew.
12. Before sailing, get acquainted with the nature of the water surface, obstacles and current.
13. The boat is not intended for long ‑term mooring on the surface.
14. After use in salt water, the boat must be washed with fresh water and dried.
15. Store the boat dry and thoroughly cleaned.
16. Do not use the compressor, as this could over ‑blow, crack the seams or completely destroy the boat.
17. Make minor repairs according to the Boat Repair Instructions.
18. Extensive repairs must be performed by an authorised service centre.

www.mivardi.cz
Producer : WEIHAI XIANGDA MARINE CO. LTD.
Gushan Town, Weihai City
P. R. China
Importer and authorised service
Importeur & Autorisierter Service:
Mivardi, s. r. o., 2401/4, 193 00 Praha 9,
Tel: +420 281 921 962 / www.mivardi.czwww.mivardi.com

References

• Mivardi
• Mivardi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>