PRISM HARDSCAPES Fuego Fire Table Instruction Manual

Fuego
Fire Table
Installation, Operation & Maintenance Manual

WARNING: THIS APPLIANCE IS FOR OUTDOOR USE ONLY!
This manual should remain with the parties responsible for the operation.

Section 1 General Description

1.1 Product Dimensions
Fuego 54 Fire Feature:

Fuego 89 Fire Feature:

Note: Enclosure should be located a minimum of 3-4ft. away from the fire feature. Ensure the enclosure is not placed directly on/over the propane hose that could otherwise kink, pinch, or cut off the gas supply.

1.2 Safely Moving Fire Feature

• NEVER ATTEMPT TO MOVE YOUR FIRE FEATURE BY YOURSELF
• WRAP FURNITURE BLANKET AROUND THE ENTIRE BODY OF THE UNIT
• PLACE A PIECE OF ¾” PLYWOOD BETWEEN DOLLY AND THE FIRE FEATURE FOR INCREASED STABILITY WHILE MOVING
• USE DOLLY TO NAVIGATE THE UNIT TO THE FINAL POSITION

DO NOT USE A WHEELBARROW OR OTHER UNBALANCED EQUIPMENT TO MOVE UNIT

| CAREFULLY REMOVE UNIT FROM CRATE AND PLACE ONTO MOVING DOLLY
---|---
|
PLACE FIRE FEATURE WITH BASE DOWN TO MOVE OR| PLACE FIRE FEATURE ON SIDE TO MOVE
SECURE PAN/BURNER PRIOR TO TILT
(ONLY FOR SQUARE OR RECTANGLE UNITS)
|
| GENTLY PLACE FIRE FEATURE INTO FINAL POSITION

Safety Instructions

CALIFORNIA PROPOSITION 65
This product can expose you to Chromium, which is known in the state of California to cause cancer, birth defects, or other reproductive harm.
(for more information, go to: www.p65warnings.ca.gov)

Prior to installation, read and follow all warning notices and instructions provided with this product.
Failure to do so may result in property damage, personal injury, and/or death. Improper installation and/or operation may result in exposure to carbon monoxide and flue gases which can cause serious injury, property damage, and/or death. For installations in the vicinity of occupied/living areas, Prism Hardscapes strongly recommends the installation of carbon monoxide detectors within reach of this appliance and in any adjacent occupied spaces. Improper installation and/or operation will void the warranty.

THIS APPLIANCE IS FOR USE WITH PROPANE GAS ONLY. AT NO TIME ARE SOLID OR ALTERNATIVE FUELS TO BE USED WITH THIS APPLIANCE.
Do not store or use gasoline or other flammable vapors and liquids within the vicinity of this or any other appliance.
Prism Hardscapes strongly recommends the installation of Carbon Monoxide detectors within reach of this appliance and in any adjacent occupied spaces.

WARNING
Before installing this product, read and follow all warning notices and instructions provided. Failure to do so may result in serious injury, property damage, and/or death. For additional product references and copies of these instructions, visit our website at prismhardsacapes.com

WARNING
This appliance may produce carbon monoxide which has no odor. Using this appliance in an enclosed space such as a motorhome, camper, car or home may result in death.
The appliance should be serviced annually, and any parts that require replacement should be replaced only by a certified service professional using parts recommended by the manufacturer.
Do not alter any component or design of this unit as it may alter the operation and result in injury, property damage, and/or death. The altering unit will also automatically void the warranty.
This fire feature is not intended for cooking. Do not place anything on or in the fire feature.
Never use the fire feature in windy conditions.
Do not touch hot surfaces, hot media (rocks/glass/etc.), or open flames.
Do not reach, jump, or walk across the unit, media, or open flames.
Do not ignite fire feature when media (rocks/glass/etc.) are wet. Doing so may cause media to crack and burst.
It is important to inspect your fire feature before every use. Make sure there are no obstructions or combustible materials on or near the unit.
Wipe down the surface of the unit before every use and immediately clean any spills or messes on or around the unit.
Consistently check hoses and fittings for cracks, abrasions, and leaks (at least once a month).
Do not leave pets or children unattended around the fire feature.
Use the designated cover when the unit is not in use.
If the burner goes out, immediately turn off propane gas and wait several minutes to ensure that there is no residual gas. Then turn the gas back on and re-light the burner.
Inspect unit and components prior to initial start-up and before/after each use.

Section 3 Installation Details

3.1 Gas Requirements
The fire feature should be placed on a flat and level surface. It will arrive with the burner and burner plate set inside the unit. Burner hardware has been installed at the factory but will need to be checked for proper tightness after transportation. Refer to the corresponding section below for set-up on your unit. All units must have clearance to the combustible surface of 4ft on all sides & 6ft from the top.

3.1.1 Propane Gas
Gas Pressure: 11 inches water column
Gas Input Flow: 65,000 BTUs/HR
Make sure the foundation is flat and level prior to placement. Units that use liquid propane will come with a burner, orifice, flex hose, and regulator that will attach to the propane tank. This gas hose will need to go from the tank to the burner. The hose should connect from the key valve within the unit, through a vent underneath, and to the propane tank. Make sure all fittings are tightened properly with a wrench, do not hand tighten! An additional flex hose will be attached to the other end of the key valve to the flare fitting at the bottom of the burner. The arrow on the key valve should be pointing in the direction of the gas flow (towards the burner plate on your fire feature).
Fire features do not include a propane cylinder; you will need to provide one. The liquid propane supply cylinder must be constructed and marked in accordance with the specifications for propane gas cylinders as required by the U.S. Department of Transportation (DOT).

3.2 Internal View of Components

3.3 Propane Gas Quick Connection
The fire feature is equipped with a quick connect brass connection. Coupled with the brass connection on the propane hose to quickly and conveniently provide proper pressure to operate the fire feature as well as a sealed connection to the tank.

To Connect:

1. Pull the sleeve back on the hose connection.
2. While the sleeve is in the back position push onto the connection on the fire feature receiver.
3. Release sleeve. (sleeve will automatically slide into place)
4. Gently tug/pull on the hose to ensure a connection has been made.

To Disconnect:

1. Push inwards on the connection, then pull back on the sleeve.
2. While the sleeve is in the back position pull away the connection on the fire feature receiver.
3. Release sleeve. (sleeve will automatically slide into place)

Section 4 Operation

4.1 Ignition
Refer to the section below according to which ignition system you purchased. An initial burner test should be done prior to filling the pan with media (rocks/glass/etc.)
4.1.1 Manual Light
You will need a fireplace lighter, do not use a match or cigarette lighter as they are much shorter and will light the fuel too close to the burner which may result in serious injury. Ignite your fireplace lighter and hold the tip close to the burner. Insert the fire table key and turn it to the ON position to start gas flow to the burner- if you are using a propane tank unit, please note you will need to open the valve on your tank first. If your burner does not light within 5 seconds, turn the key to the OFF position and wait 10 seconds before trying again. If the burner still does not light, call your local gas technician to determine if there is a problem. Once the burner lights, immediately remove your hand and allow the burner to operate for a few minutes before turning it off. Make sure the valve is properly closed every time you leave your fire feature unattended and remove the key. For propane units, ensure that valve on the tank is completely closed when the fire feature is not used.
You are now ready to place the fire media onto the burner pan. Slowly pour media onto the pan and spread evenly.
Fire media should be sparsely spread out enough to cover the pan. Only use the recommended amount of media in your unit (the amount provided), overfilling may result in smaller flame and gas buildup which may cause an explosion. Fresh air must be able to pass through the unit. Do not block or obstruct any vents on the lower and upper parts of the fire feature. These are designed to ensure proper combustion and ensure no buildup of residual gases within the unit.

4.1.2 Electronic Ignition
Prism Hardscapes offers a separate installation guide for the Electronic PH- Ignite System. All other electronic system guides must be requested from their corresponding manufacturers.
CAUTION: Open flames will ignite combustible materials such as clothing, fabric, hair, etc. which may result in serious injury, property damage, and/or death. Be cautious of the open flames while the burner is lit.
4.2 Adjustment
Allow the fire feature and media to cool down before moving or adjusting. This may take from 30 minutes to 1 hour depending on the size of the fire feature. Any shifting of fire media or features should be done after the entire unit has cooled. Also prior to movement, ensure that all gas valves are completely closed and disconnected.
Refer to Section 1.4 for instructions on how to safely move your unit.
4.3 Caring for Unit
It is recommended to wipe the unit down before every use, and always clean any spills immediately so as not to allow stains to set in. Cleaning can be done with mild soap, water, and a rag. We also recommend resealing the unit after 2 years with a water-based concrete sealer

Section 5 Troubleshooting

Refer to the section below according to issue and gas source.
BURNER WILL NOT LIGHT

from the line.
Debris in Gas Line| Confirm gas line is clear and free of obstruction (insulation, dirt, excess pipe sealer, water, etc.). Clearing a line of debris may require help from a professional.
Improper Gas
Pressure| Check if the tank is low or empty, and may need to refill or replace.

BURNER WILL NOT STAY LIT

Improper Gas
Pressure| Check if the tank is low or empty, may need to be refilled or replaced.
Improperly Applied Fire Media| **** Media may be too dense; media will need to be reduced and evenly spread.

NOISE
Note: Only use propane gas hose supplied by the manufacturer as they have been tested for noise.

recommendations (Refer to the subsection for your gas type in Section 3).

UNIT IS SMOKING

both may need to be refilled or replaced.
Excessive Flame Blockage| Separate and spread media (rocks or glass) evenly to allow flames to spread and pass-through media more evenly.
Improper Air/Fuel Mixture| Remove any foreign items or other combustible materials from the unit & check for proper orifice sizing.
---|---

BURNER FLAME IS TOO HIGH OR TOO LOW

Incorrect Gas Supply
Pressure| Propane Gas Units: Inspect propane tank and hose, one or both may need to be refilled or replaced.
Blocked burner ports or burner orifice| Clear burner ports and orifice of foreign particles or debris and wipe clean.
Improper Orifice Size| Verify burner orifice is the proper size for the fuel being used. Consult with the factory by emailing
tech-support@prismhardscapes.com.

UNIT PRODUCING UNWANTED ODORS

flowing through the hose up to the igniter valve). Inspect hose(s), and check for any leaks at all connections and fittings by using soapy water, and checking for bubbles. If the leak is found, turn off gas immediately and contact support for replacement component(s).
If no leak is found, inspect the propane tank for damage or defect; the tank may need to be replaced.

BATTERY IGNITION

test/change the required AA battery.
Not Lighting| Igniter: check the battery.
Igniter: check igniter probe wire connection behind battery housing. (if faulty call support, at 951-600-1123)
Fuel: check fuel source/hose.

COLOR FADING

mortar retailer and apply a coat to concrete areas every year.

Section 6 Warranty

Prism Hardscapes LLC offers a 1-year limited warranty against manufacturer defects. Prism Hardscapes will repair or replace product which has been proven to be defective in workmanship and/or material. If the unit is confirmed defective and is not repairable by a qualified Prism Hardscapes representative, the unit will be replaced FOB PRISM HARDSCAPES facility. The buyer must provide proof of purchase along with the date of delivery to the end user and arrange to ship associated with the replacement of the unit. Prism Hardscapes will not be responsible for any defects resulting from misuse, user error, installation error, abuse, repair, or alteration. The use of wood or fuels other than those specified for use with this unit by Prism Hardscapes will void the warranty immediately. Under no circumstances will Prism Hardscapes be liable for incidentals or consequential damage resulting from defective products. This warranty is Prism Hardscapes’ sole warranty, all others expressed or implied whether of merchantability, the fitness of purpose, or otherwise, are therefore disclaimed by Prism Hardscapes. Prism Hardscapes is not responsible for any injury or mishap related to misuse, abuse, or lack of judgment in choosing fire display locations.
warranty@prismhardscapes.com

We create visionary designs coupled with handcrafted processes.
11150 Business Circle, Cerritos, Ca 90703
www.prismhardscapes.com
• Phone: 951-600-1123
• Fax: 951-600-1109

References

• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>