SANUS CFR2115 34 Inch Tall Steel Component Rack Instruction Manual

SANUS CFR2115 34 Inch Tall Steel Component Rack

We’ll Make It Stress-Free
If you have any questions along the way, just give us a call. 1-800-359-5520. We’re ready to help!
Scan for more information san.us/891

IMPORTANT SAFETY INSTRUCTIONS ­ SAVE THESE INSTRUCTIONS PLEASE READ

ENTIRE MANUAL PRIOR TO USE

Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment. The total weight capacity for the CFR2100 series:

• CFR2115 226.8 kg (500 lb)
• CFR2127 340.2 kg (750 lb)
• CFR2136 385.5 kg (850 lb)
• CFR2144 453.6 kg (1,000 lb)

Each 2U shelf supports up to 22.6 kg (50 lb), and each 1U shelf supports up to 13.6 kg (30 lb). Each optional 3U shelf supports up to 36.2 kg (80 lb).

CAUTION : Avoid potential personal injuries and property damage!

• Do not exceed the stated weight capacities.
• Do not shake, tilt, rock, sit, stand, or climb on your Component Series Rack. Tipping may cause injury or death.
• Do not move large racks by yourself; due to weight and height, assistance is required.
• To avoid instability do not pull out more than one optional drawer or slide out equipment at a time.
• Before moving, make sure all optional drawers and slide out equipment are secured and door is closed and secured.
• Use extreme caution when moving a loaded rack! Push, DO NOT pull, loaded rack slowly over a short, smooth, level distance. Avoid sudden starts and stops to minimize the strain placed on casters.
• Do not use this product for any purpose not explicitly specified by manufacturer.
• If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact manufacturer Customer Service or call a qualified contractor.
• Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

NOTE : Due to continuous product improvement, images shown in this manual may vary from actual product.

Do you have all of the tools needed?

Unpacking

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
Supplied parts are located inside of the rack. To access the parts, remove the back panel.

Parts and Hardware

Load Your Components

CAUTION : Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:
To prevent instability:

• Always load the rack from the bottom up and load the heaviest item first.
• 50% of the total weight should be mounted in the lower 1/3 of the rack.

CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:
To prevent instability:

• Always load the rack from the bottom up and load the heaviest item first.
• 50% of the total weight should be mounted in the lower 1/3 of the rack.
• Follow these additional requirements when loading rack on its back and then lifting rack to an upright position:
  1. Leveling feet, if installed, need to be adjusted all the way in.
  2. You must not load more than 20% of the total rated load prior to lifting rack to upright position.
  3. All equipment should be securely fastened to the rack.
  4. Use caution when lifting rack to upright position as casters may roll. Assistance is required.

Using Backstops and Component Straps

Rack Shelf Backstops
NOTE : rear view with back panels removed.

1. Insert backstop 03 into slot behind component.
2. Slide backstop 03 forward until firmly against component and twist 90 degrees.

Component Straps
NOTE : side view with panels removed.
A. Slide straps 04 through slots in sides of shelves.
B. Wrap straps 04 over component to secure.

Access Panels for Cable Management

Install Fan for Additional Ventilation (Top or Bottom)

CAUTION : Avoid damage to your components due to overheating. Make sure that there is adequate space between each unit for proper airflow. Operating temperature inside the rack must not exceed 104°F (40°C).
To install fan:
Remove the vented panel. CAUTION : Cut edges may be sharp.
Remove any metal burrs that remain in the panel frame. Mount the cooling fan using the screws 05 included.

Adjust Shelves and Blanking Panels

NOTE : Align the bottom of the shelf or blanking panel B with the lines L on the rack rail.

Adjust Rack Rails

Remove the shelves and blanking panels before adjusting the rails. Adjust the right and left rails evenly.
NOTE : For clarity, the front door, top, and side panels are not shown.

Switch Back Panels

1. 1. Remove large upper panel.
2. Remove small lower panel and frame.
3. Fit bottom of large panel into rack frame and angle the panel up until sliding locks snap in place.
4. Flip small panel 180 degrees.
5. Screw panel frame into rack frame and replace small panel.
   

Reverse the Front Door

Remove the door

1. Turn upper door pin to release from locking tab and pull down to release door from rack and lift door from rack frame.

2. Release upper pin and turn it back to secure it with the locking tab.

3. Remove spacer from bottom door pin.
   NOTE : Spacer must be used with pin on bottom of door.
   
   Flip the door

4. Fit spacer onto bottom pin and fit bottom pin into bottom mounting hole in rack.

5. Turn upper pin to release from locking tab and pull down. Fit pin into upper mounting hole in rack.

6. Release pin and turn pin to secure it with locking tab.

Add Keyed Lock to Door (Sold Separately)

Ganging Racks (Ganging Kit Sold Separately)

Level Feet

Adjust the feet to level the rack. Tighten nuts until they are flush with the bottom of the rack.
CAUTION : To avoid potential injury or property damage, always ensure that your rack is level.

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
©2014 Milestone AV Technologies. All rights reserved. Sanus is a division of Milestone. All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

SANUS
• 6436 City West Parkway
• Eden Prairie, MN 55344
USA 6901-002396 01

NEW SANUS FOUNDATIONS® COMPONENT SERIES AV RACKS

Introducing the SANUS 100 Series Racks – the Second Generation

The engineers at SANUS took the Component Series racks to the next level with the SANUS 100 Series Racks – the Second Generation. Constructed of heavy-gage welded steel, the 100 Series come pre-assembled with vented shelves and blanking panels to simplify ordering and installation. Improvements to the Second Generation include both side and back quick-release panels for easy access to components and additional cooling vents at the top and bottom of the racks for more efficient temperature management The lockable tempered glass front door can be placed on the left or right and multiple 3U removable panels add increased versatility. The Second Generation of SANUS Component 100 Series Racks come in four sizes (15U, 27U, 36U, and 44U) with the added ability to be gangable so you’ll always have the right solution for every installation.

www.sanus.com
800.359.5520

MODEL: CFR2115

• DESCRIPTION
  15U AV Rack

• DIMENSIONS (W X D X H)
  23.6″ x 23.6″ x 34″ / 60 x 60 x 86.4 cm

• RACK SPACES
  15U

• WEIGHT CAPACITY
  500 lbs / 226.8 kg

• PACKAGE DIMENSIONS (W X D X H)
  26.4″ x 26.4″ x 33.46″ / 67 x 67 x 85 cm

• PACKAGE WEIGHT
  124.4 lbs. / 56.43 kg

• LIST PRICE
  $579.99
  

• SHELVES (1) 1U (1) 2U (1) 3U | BLANKING PANELS (1) 1U (1) 2U (1) 3U | TIE BARS (1) SHELVES (2) 1U (2) 2U (2) 3U | BLANKING PANELS (1) 1U (1) 2U (1) 3U | TIE BARS (2)

MODEL: CFR2127

• DESCRIPTION
  27U AV Rack

• DIMENSIONS (W X D X H)
  23.6″ x 23.6″ x 55″ / 60 x 60 x 139.7 cm

• RACK SPACES
  27U

• WEIGHT CAPACITY
  750 lbs / 340.2 kg

• PACKAGE DIMENSIONS (W X D X H)
  26.4″ x 26.4″ x 53.2″ / 67 x 67 x 135 cm

• PACKAGE WEIGHT
  191.5 lbs. / 86.9 kg

• LIST PRICE
  $799.99
  

• SHELVES (2) 1U (2) 2U (2) 3U | BLANKING PANELS (1) 1U (1) 2U (1) 3U | TIE BARS (2)

MODEL: CFR2136

• DESCRIPTION
  36U AV Rack

• DIMENSIONS (W X D X H)
  23.6″ x 23.6″ x 70.5″ / 60 x 60 x 179.15 cm

• RACK SPACES
  36U

• WEIGHT CAPACITY
  800 lbs / 362.9 kg

• PACKAGE DIMENSIONS (W X D X H)
  26.4″ x 26.4″ x 66.1″ / 67 x 67 x 168 cm

• PACKAGE WEIGHT
  218 lbs. / 98.9 kg

• LIST PRICE
  $1,199.99
  

MODEL: CFR2144

• DESCRIPTION
  44U AV Rack

• DIMENSIONS (W X D X H)
  23.6″ x 23.6″ x 84.75″ / 60 x 60 x 215.3 cm

• RACK SPACES
  44U

• WEIGHT CAPACITY
  1000 lbs / 453.6 kg

• PACKAGE DIMENSIONS (W X D X H)
  26.4″ x 26.4″ x 82.3″ / 67 x 67 x 209 cm

• PACKAGE WEIGHT
  244.7 lbs. / 111 kg

• LIST PRICE
  $1,499.99
  

• SHELVES (2) 1U (4) 2U (3) 3U | BLANKING PANELS (2) 1U (3) 2U (2) 3U | TIE BARS (3)

• Removable panels
  
  

• Ganging ability
  

• Repositionable 3U openings
  

• Swivel casters and adjustable feet
  

• Pre-assembled
  

CONFIGURATION

• 3U OPEN
• 1 U SHELF
• 1U SHELF
• 1U OPEN
• 3U BLANK PANEL
• 2U SHELF
• 2U BLANK PANEL
• 2U SHELF
• 1 U BLANK PANEL
• 2U OPEN
• 3U SHELF
• 1U OPEN
• 3U SHELF
• 2U OPEN

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SANUS SYSTEMS; A PRODUCT DIVISION OF MILESTONE AV TECHNOLOGIES. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SANUS SYSTEMS IS PROHIBITED.

Customer Support

Thank you for choosing Sanus!
Please take a moment to let us know how we did:
Call us : 1-800-359-5520
UK : 0800 056 2853
Email us : info@sanus.com
Leave a review : sanus.com

References

• Racks and Furniture | Products | SANUS
• SANUS | #1 Brand of TV Wall Mounts in the U.S.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>