TA FXO Gateway Integration Software
User Guide

Connect Yeastar P-Series PBX System and Yeastar TA FXO Gateway

This guide provides a configuration example to describe how to extend analog FXO trunks for Yeastar P-Series PBX System.
Background
The instructions provided in this guide are based on the following test environment.

Objectives
This guide provides guidance based on the above scenario to help you achieve following objectives:

• Connect Yeastar P-Series PBX System and Yeastar TA1610 Gateway
• Make Outbound Calls through the Extended FXO Trunks
• Receive inbound calls through the extended FXO trunks

Connect Yeastar P-Series PBX System and Yeastar TA1610 Gateway
This topic introduces the steps to connect Yeastar P-Series PBX System and Yeastar TA1610 via SIP peer trunks. After the two devices are connected, 16 FXO trunks are ex­tended on the Yeastar P-Series PBX System.
Step1. Create a SIP peer trunk on Yeastar IPPBX

1. Log in to the PBX management portal, go to Extension and Trunk > Trunk, click Add.

2. Configure the trunk basic settings.
   • Name: Enter a name to help you identify it. For example, Connect-to- TA1610Gateway.
   • Trunk Status: Select Enabled.
   • Select ITSP Template: Select General.
   • Trunk Type: Select Peer Trunk.
   • Transport: Select UDP.
   • Hostname/IP: Enter the IP address of Yeastar TA1610 gateway. In this exam­ ple, enter 192.168.6.24.
   • Port: Enter the SIP port of Yeastar TA1610 gateway. In this example, enter the default port 5060.
   • Domain: Enter the IP address of Yeastar TA1610 gateway. In this example, en­ ter 192.168.6.24.

3. Click Save and Apply.

4. Wait for seconds and check the trunk status on the Trunk page.
   If the status shows , Yeastar IPPBX is connected to the Yeastar TA1610 gateway.

Step2. Create a SIP peer trunk on Yeastar TA1610 Gateway

1. Log in to the gateway web interface, go to Gateway > VoIP Settings > VoIP Trunk#click Add New Trunk.

2. In the pop-up window, configure the following settings:
   • Trunk Type: Select Service Provider.
   • Type: Select SIP.
   • Provider Name: Enter a name to help you identify it.
   • Hostname/IP: Enter the IP address of Yeastar IPPBX and the SIP port. In this example, enter 192.168.6.124 and the default SIP port 5060.

3. Click Save and Apply Changes.

4. Wait for seconds and check the trunk status on the Status > Port/Trunk page.
   If the status shows “OK”, Yeastar TA1610 gateway is connected to the Yeastar IPP­ BX.

Make Outbound Calls through the Extended FXO Trunks

After the connection, you can make outbound calls through the extended FXO trunks.
Scenario
The application scenario is shown as the following figure. Procedure

1. Create an outbound route on Yeastar IPPBX to allow users reach the Yeastar TA1610 gateway.
   a. Log in to the PBX management portal, go to Call Control > Outbound Route, click Add.
   b. Configure the following settings for the outbound route and leave other settings  as default.
   • Name: Enter a name to help you identify it. For example, TO-TA1610.
   • Dial Pattern: Set the dial patterns according to your needs. In this exam­ ple, set Pattern to 9., set Strip to 1.
   Users should dial prefix 9 before the target number. For example, to call number 123456, users should dial 9123456.• Trunk: Select the SIP peer trunk that is connected to the Yeastar TA1610. In this example, select the trunk Connect-to-TA1610-Gateway.![Yeastar TA FXO Gateway Integration Software

• Figure 8](https://manuals.plus/wp-content/uploads/2022/12/Yeastar-TA-FXO- Gateway-Integration-Software-Figure-8.png)• Extension/Extension Group: Select the extensions that are allowed to make calls through this outbound route. In this example, select the all ex­tensions.c. Click Save and Apply.

  2. Create an IP->Port route on Yeastar TA1610 gateway.
     a. Log in to the gateway web interface, go to Gateway > Route Settings > IP>Port, click Add IP->Port Route.
     b. In the pop-up window, configure the route.
     • Simple Mode: Yes
     • Route Name: Enter a name to help you identify it.
     • Call Source: Select the SIP trunk that is connected to Yeastar IPPBX. In this example, select the trunk SPS – P560.
     • Call Destination: Select the FXO trunks that will be used to call out. In this example, select all FXO trunks.c. Click Save and Apply Changes.

  3. Make a test call from a PBX extension.
     For example, to call number 1588035242, you need to dial 91588035242.

Receive inbound calls through the extended FXO trunks

After the connection, you can receive inbound calls through the extended FXO trunks.
Scenario
The application scenario is shown as the following figure.

Procedure

1. Create an inbound route on Yeastar IPPBX to accept incoming calls from Yeastar TA1610.
   a. Log in to the PBX management portal, go to Call Control > Inbound Route, click Add.
   b. Configure the following settings for the inbound route and leave other settings as default.
   • Name: Enter a name to help you identify it. For example, From-TA1610.
   • DID Pattern:

   DID Matching Mode: Select DID Pattern.

   Pattern: Enter a DID number. This DID number will be used to match the

   incoming calls from TA1610 gateway.
   In this example, enter 123456.• Trunk: Select the SIP peer trunk that is connected to the Yeastar TA1610. In this example, select the trunk Connect-to-TA1610-Gateway.• Default Destination: Select a destination for the inbound route.
   In this example, set the Destination to extension 2000. When incoming calls from TA1610 gateway reach the PBX, the calls will be routed to ex­ tension 2000.c. Click Save and Apply.

2. Create a Port->IP route on Yeastar TA1610 gateway to route incoming calls to Yeast­ ar IPPBX.
   a. Log in to the gateway web interface, go to Gateway > Route Settings > Port>IP/Port, click Add Port->IP/Port Route.
   b. In the pop-up window, configure the route.
   • Simple Mode: Yes
   • Route Name: Enter a name to help you identify it.
   • Call Source: Select the FXO trunks that will be used to call out. In this ex­ample, select all FXO trunks.
   • Call Destination: Select the SIP trunk that is connected to Yeastar IPP­ BX. In this example, select the trunk SPS – P560.
   • Hotline: Enter the DID number that is set on the inbound route of Yeastar IPPBX. In this example, enter 123456.

3. Make a test call to one of the extended FXO trunks.
   For example, the extended FXO trunk’s number is 505525301, you call dial 505525301 on your mobile phone. The call will be routed to extension 2000.

Yeastar Information Technology Co.Ltd.
Support: +86-592-5503301
Support: support@yeastar.com
****https://www.yeastar.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>