BLACKBIRD P/N 43395 4K 6×2 HDMI Matrix with Audio User Manual

BLACKBIRD P/N 43395 4K 6×2 HDMI Matrix with Audio

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.

• This device is intended for indoor use only.
• Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before reapplying power.
• Do not touch the device, the power cord, or any other connected cables with wet hands.
• Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.
• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
• This device has no user serviceable parts. Do not attempt to open, service, or modify this device.

INTRODUCTION

This 4K 6×2 HDMI® Matrix allows you to independently distribute any of six HDMI inputs to two HDMI outputs. It supports video resolutions up to 4K@30Hz, including 1080p@60Hz and 3D video . The audio associated with either output can be extracted and sent to an external amplifier or powered speakers using the analog 3.5mm, digital coaxial, or digital optical (Toslink®) audio outputs. Output A supports the Audio Return Channel (ARC) HDMI feature, which allows audio originating from the connected television to be distributed to the audio outputs. It supports a Picture-in-Picture (PiP) mode when the output resolution is 4K@30Hz and includes an IR remote control.

FEATURES

• Independently distributes up to six HDMI® inputs to two HDMI outputs
• Supports video resolutions up to 4K@30Hz, including 1080p@60Hz and 3D video
• 9.0 Gbps video bandwidth
• Supports up to 36-bit Deep Color
• Supports HDCP™ 1.4
• Includes analog 3.5mm stereo, digital coaxial, and digital optical (Toslink®) audio outputs
• Output A supports the Audio Return Channel (ARC) HDMI feature
• Supports the Consumer Electronics Control (CEC) HDMI feature
• Supports 2.0, 5.1, and 7.1 channel audio, including Dolby TrueHD™ and DTS-HD Master Audio™
• Supports a Picture-in-Picture (PiP) mode when the output resolution is 4K@30Hz
• Includes an IR remote control

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at
support@monoprice.com. Check the website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.

• 1x 6×2 HDMI® Matrix
• 1x IR Remote Control
• 1x AC Power Adapter
• 1x User’s Manual

PRODUCT OVERVIEW

Remote Control

1. Power Button: Press the Power
   Button to turn the matrix on or to put it into standby mode.

2. Audio Button: Press the Audio
   Button to cycle through the available audio output modes. The cycle order is 2.0, 5.1, and 7.1.

3. ARC Button: Press the ARC
   Button to turn the Audio Return Channel (ARC) feature on or off. Only Output A supports ARC and the connected television must support ARC.

4. PiP Section: Press the PiP Button to turn the Picture-in-Picture (PiP) mode on or off. PiP is supported only when the output resolution is 4K@30Hz. Press the Select Button to cycle through the inputs for the PiP window. Once the desired input for the PiP window is displayed, press the Enter Button to confirm the selection.

5. OUT A Section: Press one of the numbered buttons to directly select one of the six inputs to distribute to Output A.

6.  OUT B Section: Press one of the numbered buttons to directly select one of the six inputs to distribute to Output B.

7. Audio Section: Press the OUT A Button to extract the audio from Output A to the audio outputs. Press the OUT B Button to extract the audio from Output B to the audio outputs. Press the A↔B Button to swap the Output from which audio is extracted.
   Matrix

8. INPUT 5/INPUT 6: Two HDMI® ports for connecting HDMI video source devices.

9. INPUT INDICATORS: Two rows of six LEDs each, labeled A and B. One of the LEDs on each row illuminates to indicate the selected input for each output.

10. AUDIO INDICATORS: Four LEDs indicate whether ARC is on or off, and the selected audio mode (2.0, 5.1, 7.1). When the ARC LED is on, the audio from the television connected to output A is being sent to the STEREO, COAXIAL, and TOSLINK® outputs. The 2.0, 5.1, or 7.1 LED illuminates to indicate the selected audio mode.

11. IR: IR “eye” for receiving signals from the included IR remote control.

12. OUTPUT A: Press the button to cycle through the available inputs for Output A.

13. OUTPUT B: Press the button to cycle through the available inputs for Output B.

14. ARC: Press the button to turn ARC on or off. When ARC is on, the ARC LED in the AUDIO INDICATORS section illuminates.

15. AUDIO: Press the button to cycle through the three audio modes (2.0, 5.1, 7.1). The corresponding LED in the AUDIO INDICATORS section illuminates to indicate the selected audio mode.

16. RESET: Press the button to reset the matrix to its factory default settings.

17. POWER: The LED illuminates when the matrix is powered on.

18. DC/5V: DC barrel connector for connecting the included AC power adapter.

19. HDMI 1/HDMI 2/HDMI 3/HDMI 4: Four HDMI® ports for connecting HDMI video source devices.

20. OUTPUT B: HDMI port for connection an HDMI display.

21. OUTPUT A: HDMI port for connecting an HDMI display. OUTPUT A supports the ARC feature.

22. STEREO: 3.5mm 2-channel analog audio output jack for connecting an external amplifier or powered speakers. When the audio mode is set to 5.1 or 7.1, there will be no sound on this output.

23. COAXIAL: Digital coaxial audio output for connecting an external amplifier. If the amplifier does not support the selected audio format (e.g., Dolby TrueHD™, DTS-HD Master Audio™, etc.), there will be no sound on this output.

24. TOSLINK: Digital optical audio output for connecting an external amplifier. If the amplifier does not support the selected audio format (e.g., Dolby TrueHD™, DTS-HD Master Audio™, etc.), there will be no sound on this output.

SAMPLE CONNECTION DIAGRAM

CONNECTION

Perform the following steps to connect the matrix to your system.

1. Ensure that all devices to be connected are powered off and disconnected from their power sources.
2.  Using a High Speed HDMI® Cable (available separately), plug one end into an HDMI input on one of your displays, then plug the other end into the OUTPUT A port on the matrix. If you want to use the ARC feature, you must connect to an input that supports ARC.
3. Using a High Speed HDMI® Cable (available separately), plug one end into an HDMI input on your second display, then plug the other end into the OUTPUT B port on the matrix.
4. (Optional) Using a digital optical (Toslink®) cable (available separately), plug one end into the digital optical input on your amplifier, then plug the other end into the TOSLINK port on the matrix.
5. (Optional) Using a digital coaxial cable (available separately), plug one end into the digital coaxial input on your amplifier, then plug the other end into the COAXIAL port on the matrix.
6. (Optional) Using a 3.5mm audio cable (available separately), plug one end into your amplifier or powered speakers, then plug the other end into the STEREO jack on the matrix.
7. Using a High Speed HDMI Cable (available separately), plug one end into one of the HDMI inputs on the matrix, then plug the other end into the HDMI output on one of your video source devices. Repeat for up to five additional video source devices.
8. Plug one end of the included AC power adapter into the DC/5V connector on the matrix, then plug the other end into a nearby AC power outlet.
9. Pull the film out of the remote control to allow its battery to connect to the battery terminal.
10.  Aim the remote control at the IR “eye” on the matrix, then press the Power Button on the remote to turn the matrix on.
11. Plug in and power on all connected equipment. Use the controls on the remote control to switch to each input for each output to verify that the system is connected properly.

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links.
To download the latest drivers, firmware, manuals, etc., go to www.monoprice.com and type the P/N into the search bar. If available, support files are linked at the bottom of the product page.

SPECIFICATIONS

• P/N 43395

• Video Inputs 6x HDMI®

• Video Outputs 1x HDMI with ARC, 1x HDMI

• Audio Outputs
  1x .3.5mm stereo analog, 1x digital coaxial, 1x digital optical (Toslink®)

• Maximum Video Resolution
  4K@30Hz, including 1080p and 3D video

• Video Bandwidth
  9.0Gbps/900MHz total 3.0GHz/300MHz per channel

• Input Power 5 VDC

• AC Power Adapter Input Power 100 ~ 240 VAC, 50/60 Hz

• Maximum Power Consumption 5 watts

• Operating Temperature +32 ~ +158°F (0 ~ +70°C)

• Operating Humidity 10 ~ 85% RH, noncondensing

• Storage Temperature +14 ~ +176°F (-10 ~ +80°C)

• Storage Humidity 5 ~ 90% RH, noncondensing

• Dimensions 9.3″ x 2.6″ x 1.1″ (210 x 66 x 27 mm)

• Weight 12.9 oz. (366g)

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>