BLACKBIRD MP24740 4K 4×1 HDMI Switch Quad Multiviewer User Manual

BLACKBIRD MP24740 4K 4×1 HDMI Switch Quad Multiviewer User Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.

• This device is intended for indoor use only.
• Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately remove it from its power source and allow it to fully dry before reapplying power.
• Do not touch the device, the power cord, or any other connected cables with wet hands.
• Do not expose this device to excessive vibration, extreme force, shock, or fluctuations in temperature or humidity.
• Do not expose this device to excessively high temperatures. Do not place it in, on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it in direct sunlight.
• Do not place or install this device in an area where it can be exposed to excessive amounts of dust, humidity, oil, smoke, or combustible vapors.
• Prior to operation, check the unit and power cord for physical damage. Do not use if physical damage has occurred.
• Before plugging the unit into a power outlet, ensure that the outlet provides the same type and level of power required by the device.
• Unplug this device from the power source when not in use.
• Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard.
• Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body.
• Ensure that power is turned off and disconnected before making any electrical connections.
• Remove the batteries from the controller if it will go unused for a lengthy period of time.
• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
• This device has no user serviceable parts. Do not attempt to open, service, or modify this device.

INTRODUCTION

This 4K 4×1 HDMI® Quad Multiviewer allows you to view four HDMI video sources on a single HDMI and a single VGA display at the same time. It features five display modes, three of which display all four inputs. It supports HDMI video resolutions up to 4K@30Hz and VGA resolutions up to 1920×1200. It can be controlled using the front panel buttons or the included IR remote control.

FEATURES

• 4x HDMI® video inputs, 1x HDMI and 1x VGA video outputs, and 1x 3.5mm stereo audio output
• Supports HDMI video resolutions up to 4K@30Hz
• Supports VGA video resolutions up to 1920×1200@60Hz
• Supports 2-channel LPCM audio
• Supports 1, 2, and 4 window multiview modes
• Includes an IR remote control

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.

• 1x 4K 4×1 HDMI® Quad Multiviewer
• 1x IR Remote Control
• 1x AC Power Adapter (12 VDC, 1A)
• 2x Mounting Ears
• 1x User’s Manual

PRODUCT OVERVIEW

Front Panel

1. POWER LED: The LED illuminates green when power is applied and red when in standby mode.
2. IR: IR receiver window for accepting signals from the included IR remote control.
3. CH1/CH2/CH3/CH4: Four buttons for selecting the input source for each of the four channels. The LEDs illuminate to indicate which channels are active or which input is selected. Refer to the DISPLAY MODES section for more details.
4. MODE: Momentarily press the button to cycle through the five different display modes. Press and hold the button for about 5 seconds for a full screen and equal proportion display. Refer to the DISPLAY MODES section for more details.
5. RESO: Momentarily press the button to cycle through the supported display resolutions. Press and hold the button for about 5 seconds to open or close the window display frame.
6. SERVICE: USB port for servicing at the factory only.

Rear Panel

1. INPUT: Four HDMI® ports for connecting HDMI video source devices.
2. HDMI: HDMI port for connecting an HDMI display.
3. VGA: VGA port for connecting a VGA display.
4. AUDIO: 3.5mm stereo analog audio output for connecting an external amplifier or powered speakers.
5. DC 12V: DC barrel connecting for connecting the included AC power adapter.

Remote Control

1. Press the button to turn the unit on or to put it into standby mode.
2. OSD: Press the button to open or close the display window frame.
3. RES: Press the button to cycle through the supported output video resolutions.
4. Mode: Press one of the five “window” buttons to select one of the five display modes. Press the button to start automatic cycling of the five display modes. Refer to the DISPLAY MODES section for more details.
5. Source: Press one of the four numbered buttons to select an input source. When using MODE 1, press the button to automatically cycle through the input sources. Refer to the DISPLAY MODES section for more details.
6. Audio: Press the button to turn audio muting on or off. Press the button to automatically cycle the audio through the four input sources.

DISPLAY MODES

This multiviewer features five display modes, as shown in the images below.

• MODE 1: This mode is a full screen display of a single input source. Press one of the CH buttons on the front panel or the numbered Source buttons on the remote control to select which of the four inputs is displayed. The LED on the front panel corresponding to the selected input illuminates to indicate which input is selected. Press the button on the remote control to automatically cycle through the available inputs.
• MODE 2: This mode divides the screen into four equally sized sections. The four LEDs on the front panel illuminate to indicate that all four channels are active. Press one of the CH buttons on the front panel or one of the numbered Source buttons on the remote control to cycle that channel through the available inputs.
• MODE 3: This mode divides the screen into four sections, one on each side and two in the middle. The four LEDs on the front panel illuminate to indicate that all four channels are active. Press one of the CH buttons on the front panel or one of the numbered Source buttons on the remote control to cycle that channel through the available inputs.
• MODE 4: This mode divides the screen vertically into two equal sized windows. The CH1 and CH2 LEDs on the front panel will illuminate to indicate that channels 1 and 2 are active. Press the CH1 or CH2 buttons on the front panel or the Source 1 or Source 2 buttons on the remote control to cycle that channel through the available inputs.
• MODE 5: This mode divides the screen into four sections with a single large window on the left and three small windows arranged vertically on the right. The four LEDs on the front panel illuminate to indicate that all four channels are active. Press one of the CH buttons on the front panel or one of the numbered Source buttons on the remote control to cycle that channel through the available inputs.

SAMPLE CONNECTION DIAGRAM

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links.
To download the latest drivers, firmware, manuals, etc., go to www.monoprice.com and type the P/N into the search bar. If available, support files are linked at the bottom of the product page.

SPECIFICATIONS

Supported HDMI® Resolutions

| 4K@30Hz, 1920×1200@60Hz,

1920×1080@50/60Hz,

1280×720@50/60Hz,

1024×768@60Hz

---|---

Supported VGA Resolutions

| 1920×1200@60Hz,

1920×1080@50/60Hz,

1280×720@50/60Hz,

1024×768@60Hz

HDMI Version| 1.4b
HDCP™ Version| 1.4
Color Depth| 8-bit/channel
Supported Color Spaces| RGB, YCbCr 4:4:4,

YCbCr 4:2:0

Supported Analog Audio Formats| LPCM 2.0
Supported LPCM Sampling Rates| 44.1kHz and 48kHz
Input Power| 12 VDC, 1A
AC Adapter Input Power| 100 ~ 240 VAC, 50/60 Hz
Maximum Power Consumption| 7.68 watts
Operating Temperature| +32 ~ +104°F (0 ~ +40°C)
---|---
Storage Temperature| -4 ~ +140°F (-20 ~ +60°C)
Operating Humidity| 20 ~ 90% RH, noncondensing
Dimensions| 7.3″ x 5.0″ x 0.8″

(185 x 128 x 20 mm)

Weight| 21.0 oz. (595g)

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Notice for Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Monoprice™, Blackbird™, the Blackbird logo, and all Monoprice
logos are trademarks of Monoprice Inc.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
HDCP™ is a trademark of Digital Content Protection LLC.
Blu-ray Disc™, Blu -ray™, and the logos are trademarks of the
Blu-ray Disc Association.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>