intwine connect ICG-150 Cellular Router User Guide
- June 4, 2024
- intwine connect
Table of Contents
intwine connect ICG-150 Cellular Router
What’s In The Box
- 1 ICG-150
- 2 4G LTE antennas
- 1 WiFi antenna
- 1 12V 1A power supply
- 1 5ft Ethernet cable*
- Mounting bracket kit*
Your ICG-150, out of the box
- LED indicators
- Reset button
- Dual SIM card slots
Your ICG-150, out of the box
- Primary cellular antenna connector
- Diversity cellular antenna connector
- WAN/LAN ports 1 and 2
- Power supply
- Wi-Fi antenna connector
ICG-150 LED indicator to guide
Connecting your ICG-150
- Carefully screw all three antennas into the rear of the system. Make sure to connect the 4G antennas to the ports labeled Cellular1 and Cellular2. Connect the WiFi antenna to the terminal labeled Wi-Fi. Finger tighten only!
- Plug the power cable into a standard outlet and plug the other side into the port on the rear of the ICG-150.
- Watch the LEDs to verify that you successfully connect to the Internet! This process can take 30- 60 seconds and should result in a solid light for 3G/4G.
- Connect your Internet-connected devices using the WiFi name and password on the bottom label or connect directly via Ethernet. You should now have Internet for any of your connected devices.
- Create a Remote Management Portal account at rmp.intwineconnect.com. Register your system and create your notifications!
For more information, including advanced configurations and mounting instructions, see the complete ICG-150 User’s Guide at www.intwineconnect.com
CERTIFICATIONS, LICENSES, AND WARNINGS
This Quick Start Guide contains safety, handling, disposal, regulatory,
trademark, copyright, and software licensing information. Read all safety
information below and operating instructions before using the ICG-150 device
to avoid injury.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
FCC CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits
are designed to provide reasonable protection against such interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions provided by Intwine Connect, may cause harmful interference to
radio communications. This device must accept any interference received,
including interference that may cause undesired operations. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by using one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or television technician for help.
Changes or modifications not expressly approved by Intwine Connect, LLC could
void the user’s authority to operate the product.
RADIATION EXPOSURE STATEMENT: This equipment complies with FCC radiation
exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instructions as documented in this manual.
SAFETY AND HAZARDS – Under no circumstances should the ICG-150 device be
used in any areas: (a) where explosives are being used; (b) where explosive
atmospheres may be present; or (c) that are proximate to any equipment which
may be susceptible to any form.
LIMITATION OF INTWINE LIABILITY – The information contained in this Quick
Start Guide is subject to change without notice and does not represent any
commitment on the part of Intwine or its affiliates. INTWINE AND ITS
AFFILIATES HEREBY SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL: (A) DIRECT,
INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY
DAMAGES, INCLUDING WITHOUT LIMITATION FOR LOSS OF PROFITS OR REVENUE OR OF
ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE THE
DEVICE, EVEN IF ENTWINE AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, AND EVEN IF SUCH DAMAGES ARE FORESEEABLE; OR (B)
CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall
the aggregate liability of Intwine and/or its affiliates arising under or in
connection with the device, regardless of the number of events, occurrences,
or claims giving rise to liability, exceed the price paid by the original
purchaser of the device.
PRIVACY – Intwine collects general data pertaining to the use of Intwine
products via the Internet including, by way of example, IP address, device ID,
operating system, browser type and version number, etc. For more information,
contact Intwine at info@intwineconnect.com.
OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT – By activating or using
your ICG-150 device, you agree to be bound by Intwine’s Terms of Use, User
License and other Legal Policies. For more information, contact Intwine at
info@intwineconnect.com
© 2022 Intwine Connect, LLC. All rights reserved. Intwine is not responsible
for omissions or errors in typography or photography. Intwine, ICG-150 and the
Intwine logo are trademarks of Intwine Connect, LLC in the US and other
countries. Other trademarks are property of their respective owners. For a
complete list of warnings, warranties, and other useful information about your
ICG-150, please visit www.intwineconnect.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>