V-TAC 80133970 LED Prismatic Fitting Installation Guide
- June 3, 2024
- V TAC
Table of Contents
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED PRISMATIC FITTING
TECHNICAL DATA:
| MODEL | VT-8-10 | VT-8-20 | VT-8-40 | VT-8-50 | VT-8-60 |
|---|---|---|---|---|---|
| WATTS | lOW | 20W | 40W | SOW | 60W |
| BODY TYPE | PLASTIC | ||||
| DF | >0.5 | >0.7 | >0.9 | >0.9 | >0.9 |
| CRI | >80 | ||||
| BEAM ANGLE | 120° | ||||
| INPUT POWER | AC: 220-240V, 50Hz | ||||
| OPERATING TEMPERATURE | -20°C to +40°C | ||||
| OPERATING HUMIDITY | 10°4-95% | ||||
| LUMINOUS EFFICACY | 1000/1200 | 2050/2400 | 4300/4800 | 5400/6000 | 6500/7200 |
| NET WEIGHT | 155+5g | 225+5g | 365+5g | 450+5g | 525+5g |
| DIMENSIONS | D1 (mm) | D2 (mm) | Ll (mm) | ||
| --- | --- | --- | --- | ||
| 10W | 24 ±1 | 75±1 | 300±2 | ||
| 20W | 24 ±1 | 75±1 | 600±2 | ||
| 40W | 24 ±1 | 75±1 | 1200±2 | ||
| SOW | 24±1 | 75±1 | 1500±2 | ||
| 60W | 24±1 | 75±1 | 1800±2 |
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.
WARNING!
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified electrician.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- For Indoor use only
- Before installation, you must carefully check the integrity of the product and accessories
- When installed, products and flammable materials to ensure that at least 0.2m distance, lighting cannot be installed in the zenith or heat wall, pay attention to low voltage and high voltage electrical wiring separately.
- To ensure that the power cord has enough length, do not kink cables. Output cables should be laid separately and at a distance from other cables.
This marking indicates that this product should not be disposed of with other
household wastes.
Caution, risk of electric shock.
INSTALLATION DIAGRAM:
INSTALLATION INSTRUCTIONS
- Choose the right position, drill two hole and insert the screw (make sure the distance between the holes is no less than50mm, Less than bracket length)
- Shrapnel point it at the hole and then install the screws
- Press the lamp body firmly into the mounting buckle to fix the lamp body, Slide the lamp body along the mounting buckle to the desired position as needed.
- Connect the wiring, use insulating tape, and waterproof tape for insulation and waterproofing, turn the power ON and test.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT:
SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST
DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>