ABBA LIGHTING STA07 3.5W Horizontal Waterproof Stair Light User Manual

3W Horizontal Waterproof Stair Light
Model NO.:STA07
AC/DC 12V
User Manual

GENERAL

All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or IEC approved wire only for input/output connections.
Remove fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.

DIMMING

This product is compatible with most common residential type dimmers. Dimming performance will depend upon dimmer, dimmer settings (dimmers with adjustments to brightness range ), wiring method, and number of LED modules. For best results, set dimmer position at maximum before adjusting to a lower light level.
Turn power off before installation, inspection, or removal.
Use all necessary precautions while performing this procedure.
Consult a qualified electrician to ensure correct branch circuit conductor. Min 90°C supply conductors. Properly ground electrical enclosure. IT IS IMPERATIVE THAT THE OUTLET BOX BE PROPERLY GROUNDED.
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE SAFETY WILL BE COMPROMISED.
This Integrated LED Fixture has no lamp/bulb to replace.
MAKE SURE THAT YOU SELECT RIGHT CCT BEFORE YOU PUT ON THE COVER, IT IS DIFFICULT TO OPEN THE FACE COVER ONCE YOU FIX IT DON’T SUBMERGE THE LIGHT BODY INTO WATER INSTALL IT IN AREA WITH HIGH SALTY MOISTURE OR CORROSIVE ENVIROMENT WILL LEAD TO FAST CORROSION SINCE IT IS NOT DESIGN FOR THIS PURPOSE

TROUBLESHOOTING

• Check that line voltage at fixture is correct.
• Ensure that there is voltage at lamp fixture wires. If there is no voltage, then check all connections.
• Check that fixture is grounded properly.

Iffixture does not light:

• Check switch to ensure that there are no defects.
• Check fuse/circuit breaker for trips, then check wiring connections.

CLEANING AND MAINTENANCE

CAUTION: Ensure fixture temperature is cool 111 enough to touch.
DO NOT clean or perform maintenance while fixture is energized.

• Clean lens and fixture with non-abrasive cleaning solution.
• Do not open fixture to clean LED. Do not touch the LED.
• Do not spray liquid directly on to LED, LED driver or wiring.

1.OUTLET BOX (EXCLUDED)
2. FIXTURE SCREWS*
3. MOUNTING BRACKET
4. BLACK FIXTURE WIRE
5. WHITE FIXTURE WIRE 6. WIRE NUTS| 7. LIGHT BODY INTERGRATED WITH FACE COVER
8. LIVE WIRE
9.NEUTRAL WIRE
10 SPRING CLIP
11. 3CCT SWITCH
---|---

Please follow these steps for installation.

1. Fix the Mounting Bracket(3) to the OUTLET BOX(1) with attached FIXTURE SCREW(2)
2. Pull the supply wires out from the OUTLET BOOS), Identify the live wire,neutral wire and ground wire(if you have problem to figure it out, please consult a qualified electrician before you do wiring),then Connect the LIVE WIRE ( 8 ) with BLACK WIRE(4), NEUTRAL WIRE ( 9 ) with WHITE WIRE(5), with the WIRE NUTS (6) attached, Please make sure that all the wires are firm connection,then seal wire nuts with silicone to ensure a stable performance in long term.
3. Select the CCT from 3000K/4000K/5000K by pushing the toggle switch left or right. WARNING: Check the CCT in this stage by turning on switch,once you confirm the light color, turn off switch. After installation, it maybe a problem to remove the LIGHT BODY( 7) to change CCT since the connection between LIGHT BODY(7) and MOUNTING BRACKET is firrn,it may destroy the SPRING CLIP(10),eventually, you can’t attach it to the MOUNTING BRACKET(3) again.
4. Check the MOUNTING BRACKET(3) is fixed flat on OUTLET BOX(1)’s surface, press the SPRING CLIP(10) evenly into the MOUNTING BRACKET(3) until all dips have a good connection with MOUNTING BRACKET(3)’s edge. 5.Installation Complete For Outdoor application: caulk the connection area between face cover and wall with outdoor rated sealant for stable performance.
   Application: can be installed indoor and outdoor, LED chip is coated with waterproof paint, CCT switch and LED driver are potted with heat dissipated compound , it can be fixed in different kind of outlet boxes, such as plastic,steel,aluminum or concrete ,also is suitable for high moisture environment or high temperature a” 7 lication( t Ica exceed 50 degree) Submerging into water is prohibited since the design is not for this application, Product et ma’ fall In short terrn,also cause your warranty void.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>