VIVITAR DVR 4K Digital Camcorder User Guide

VIVITAR DVR 4K Digital Camcorder

Read me before use! Keep the manual and all relevant information for future reference.

Friendly Tips

1. The camcorder supports an SD memory card up to 256GB. We recommend a branded class-10 SD/SDHC card which is required to be formatted in the camcorder before first-time use.
2. This camcorder is equipped with one lithium battery. Please install the battery correctly before using the camera for the first time, otherwise the camera will not charge and will not boot. this video will help you: https://www.youtube.com/watch?v=cClakxJfRxY&feature=youtu.be

WARNING To reduce the risk of fire or electric shock,

1. Do not expose the unit to rain or moisture.

2. Do not place objects filled with liquids, such as vases, on the apparatus.

3. Do not expose the batteries to excessive heat such as sunshine, fire or the like.

4. Do not ingest battery, chemical burn hazard.

5. The remote control contains a coin/button cell battery.

6. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

7. Keep new and used batteries away from children.

8. If the battery compartment does not close securely, stop using the product and keep it away from children.

9. If you think batteries might have been swallowed or placed inside any part of body, seek immediate medical attention.
   CAUTION If the battery is mishandled, the battery pack can burst, cause a fire or even chemical burns. Observe the following cautions.

10. Do not disassemble.

11. Do not crush and do not expose the battery pack to any shock or force such as hammering, dropping or stepping on it.

12. Do not short circuit and do not allow metal objects to come onto contact with the battery terminals.

13. Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a car parked in the sun.

14. Do not incinerate or dispose of in fire.

15. Do not handle damaged or leaking lithium ion batteries. Keep the battery pack out of the reach of small children. Keep the batter pack dry.

16. Replace the battery with the specified type only. Otherwise, burst, fire or injury may result.

17. Dispose of used batteries according to the instruction. Use a nearby wall outlet(wall socket) when usin the AC Adapter/Battery charger. If any malfunction occurs, disconnect the plug from the wall outlet (wall socket) immediately to disconnect from the power source.

18. If you use the product with a charge lamp, note that the product is not disconnected from the power source even when the lamp turns off.

19. Do not use the AC adapter/Battery charger placed in a narrow space, such as between a wall and furniture.

20. If static electricity or electromagnetism cause data transfer to discontinue midway (fair), restart the application or disconnect and connect the communication cable (USB, etc.) again.

About the camera

System requirement

Parts and controls

IR night vision on / off
Confirm
MODE| Open/close mode menu
MENU| Set shooting menu and system menu
UP| Upward
Turn on/off WIFI
DOWN| Downward
W/T| Digital zoom out / in
PHOTO| Take photo
Pause of recording
Shoot video button| Shoot start / end
Indicator light BUSY| Working indicator light
Indicator light CHG| Charging indicator light
Hot shoe| Base for installing handle, microphone and fill light
MIC interface| External microphone interface( 3.5mm)
HD| TV HDMI cable interface
USB| USB cable charging
Connect the computer with USB cable

Packaging contents

1. 4K Digital camcorder
2. Rechargeable lithium battery
3. Camera bag
4. USB cable
5. HDMI cable
6. Remote controller
7. Lens cover
8. Installation manual

Remote Controller

Users can controll the camcorder by remote controller. Expect as instruction of power on, the remote control can accomplish all other instructions. Note: This remote control uses CR2025 or CR2032 3V button batteries, max. distance is around 20 meters. It can remotely control the camera from a 360-degree angle. Note: Pull out the insulating paper at the bottom of the remote control before use. Insert the insulating paper when not in use to avoid battery power loss.

1. Night vision button
2. Power button
3. Photo button
4. Video button
5. Playback
6. Zoom in button
7. Zoom out button
8. Left
9. Up
10. Right
11. Down
12. Ok button
13. Menu button
14. Mode button

Charging the battery

1. Power off your camcorder, open the battery cover and insert the battery in the direction as the shown of following picture, then close the battery cover.
2. You can use supplied USB cable to charge your camcorder via a adapter(5V/1A~5V/2A) or connect to PC directly.

• The charging indicator will be turnned on in red when the battery is in charging.
• The charging indicator will be turnned off automatically when the battery is fully charged.

Normally it takes around 4-6 hours to full charging of the battery. When the battery is fully charged, the battery life is around 70 minutes for recording (Reference test data based on turn off the Wi-Fi).

Power on /off the camcorder

Open the touch screen, the camcorder will be powered on automatically. Power button You can also power on the camcorder by pressing the Power/OK/IR Night button. Power/OK/IR Night button for 3 seconds. Notes: It takes 5 seconds to power on/o the camcorder by openning the touch screen. If you open/close the touch screen twice in this reaction time, it may cause the camcorder can not before operating the machine again.

Set the camcorder

You can make custom settings of the camcorder. After power on the camcorder, tap the Menu icon of the screen or press the Menu button to open the menu. Available system settings:

Chinese/English/Japanese/Korean/Russian/German/ French/Italian/Spanish/Portuguese/Thai
Time Format| YYYY/MM/DD    MM/DD/YYYY     DD/MM/YYYY
Time Set| Set up the time of the camcorder Hour/minute/second
Date Set| Set up the time of the camcorder year/month/day
Format| (SD Card) Format/Cancel
Device Info| Product firmware version
Factory Reset| Confirm/Cancel

Insert and format the memory card

A class 10 or higher speed memory card is recommended to normal use.

1. Open the battery cover, and insert the memory card until hear the “click” sound. Insert the card with the noted corner in the direction as illusrated.
2. To remove the memory card, open the cover and push the memory card it will be popup automatically.

Format the memory card

It is recommended to format the memory card before the first use. To format the memory card, tap the Menu icon of the screen or press Menu button to open the menu. Then tap the System settings icon to open the system settings. Press Up/Down button or slide down of the screen until to “Format”, then tap Format or press Power/OK/Night vision button to get the submenu. Select “Format” to format the memory card. Note: If the memory card is not native format, the screen will pop-up a prompt: ” Card error..”, please format the memory card as above operation. Formatting the memory card will earse all the data stored on it and the data will be irrecoverable. Save your important data on PC before formatting.

Using the camcorder

After power on the camcorder, video capture mode is the default mode. Press the Mode button or tap the Mode icon of the screen to choose the desired mode. Slide down for more options

The camcorder supports to do the related settings while the camcorder is in different models. After choose your desired mode, then tap “Menu” icon of the screen or press Menu button to open the menu and select the desired settings according. Press the Photo Shutter button to take a photo, the photo will be saved in to the memory card automatically. Press the Record/Stop button to start a video recording, press again to stop the recording; you also can press Photo Shutter to pause/continue the recording. Note: The camcorder can not take a photo in video mode. IR Night vision Short press the Power/IR light/OK button, the camcorder will turn on the IR night, press again to turn off the IR lights. Mic interface The camcorder supports an external microphone with a 3.5mm connector. Note: This connector does not support headphone access.

Playback

Open the touch screen, tap the Mode icon of the screen or press the Mode button to open the mode options. Scroll down the icons of the screen, or press Down button to the end. Then tap “Playback” or press Power/OK/Light button to enter the playback mode. Press Up / Down button to scroll the images which saved in the memory card.

Playback in HDTV

The HD interface of this camcorder is only for connecting to a high-definition TV, and cannot be connected to a computer. Please plug the public port of the HD cable into the HD interface of the camcorder, and connect the other end of the port to the HD input interface of the HDTV. Note that before connecting/unplugging the HD cable, please stop recording/playing the images first. (The TV source needs to be adjusted to HD mode). The HD cable is suitable for the Mini HDMI to HDMI Cable. Note: After connecting to the HDTV, the camera’s display content will automatically switch to the HDTV, and the camera’s screen will automatically be black. It is not a malfunction.

Connect to computer

Connect the camcorder to computer is able to transfer the images to computer, also can use the camcorder as a PC camera.

1. Connect the Type-C USB port of the camcorder and the USB port of the computer with supplied USB cable.
2. The camcorder will be powered on automatically, then screen be shown the available options.

Tap the desired option or press UP/DOWN button then press Power/OK/Light button to confirm the settings. Charging Mode Select the charging mode, the camcorder supports the function of recording normally. Mass Storage Mode Select “Mass storage Mode”, the computer will display the memory card disk of the camcorder, and the computer can transfer the files into the memory card. PC Camera Select the “PC Camera” mode, the camera can be used as a webcam, live streaming, etc. Note: While the camcorder is using as a PC Camera, only the digital zoom lever can be operated on the camera, and other functions cannot be used.

Connect to the iDV-PRO app

Use the built-in Wi-Fi of the camcorder to support you to monitor the camcorder (take photo/video) easily, also easy to download the photo/videos from the camcorder to your smartphone.

Download the app and connect the camcorder’s Wi-Fi network

Search for “iDV-PRO” from Google play (Android) or Apple app store (iOS) to download the app. After power on the camcorder, hold and press the UP/Wi-Fi button to open the Wi-Fi. Then the Wi-Fi ID and password will display on the screen of camcorder. Tun on your smartphone or tablet’s Wi-Fi, tap Settings —WLAN—4K_WIFIxxxx, then enter the password according the camcorder’s screen. Note: The Wi-Fi of the camcorder can not access to the social network, it is for smartphone access to camcorder only. System requirement (of smartphone):

• Android 6.0 or higher is required
• iOS 8.0 or higher is required System settings Camcorder settings

Troubleshooting:

If you encounter problems with the camcorder, please refer to this section.

1. The camcorder cannot be turned on after installing the battery battery. (1)The battery power is insufficient, please replace the battery with a new one or charge the battery. (2) The battery is installed in reverse, please confirm that the battery is installed in the correct way. (3) The battery insulating paper is not removed.
2. The battery is not charging (1) If the red light of the charging indicator flashes, the battery is not in place or the contact is poor. Please re-install the battery until the indicator light is on (the indicator light goes out when the battery is fully charged (2)The charging indicator light is off and the charger is not plugged in properly. Please check whether the charger is connected normally. (3) The ambient temperature is lower than 10¥, which may lead to slow charging or failure to charge.
3. The remote control does not work (1) When using the remote control, pull out the bottom insulating paper. When the insulating paper is pulled out, if it still does not work, pull out the battery of the remote control and reinsert it. (2) The remote control cannot remotely control the camcorder to turn on, but can only remotely turn it off.
4. Camera crashes (1) Quickly pressing any button of the camcorder may cause the camcorder freezes. After it crashes, unplug the battery and reboot. Tip: When the camcorder is recording or taking pictures, do not quickly press the camera button. Under normal circumstances, the camcorder will display a waiting icon.
5. The memory card cannot be recognized: (1) Please check whether the memory card complies with SD card (class10), the maximum is not more than 256G. (2) Please check whether the memory card is inserted backwards. (3) When the memory card is used on the camcorder for the first time, it is recommended to format it first.

FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

VIVITAR WARRANTY

This warranty covers the original consumer purchaser only and is not transferable. This warranty covers products that fail to function properly UNDER NORMAL USAGE, due to defects in material or workmanship. Yourproduct will be repaired or replaced at no charge for parts or labor for a period of one year. What Is Not Covered by Warranty: Damages or malfunctions not resulting from defects in material or workmanship and damages or malfunctions from other than normal use, including but limited to, repair by unauthorized parties, tampering, modification or accident. To Obtain Warranty Service and Troubleshooting Information: Call 1-800-592-9541 or Visit our website at www.vivitar.com. To receive Warranty service along with the name and address of an authorized product service center, the original consumer purchaser must contact us for problem determination and service procedures. Proof of purchase in the form of a bill of sale or receipted invoice, evidencing that the Product is within the applicable Warranty period(s), MUST be presented in order to obtain the requested service. It is your responsibility to properly package and send any defective products along with a dated copy of proof of purchase, a written explanation of the problem, and a valid return address to the authorized service center at your expense. Do not include any other items or accessories with the defective product. Any products received by the authorized service center that are not covered by warranty will be returned unrepaired.

NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THOSE EXPRESSLY DESCRIBED ABOVE SHALL APPLY. DISTRIBUTOR FURTHER DISCLAIMS ALL WARRANTIES AFTER THE EXPRESS WARRANTY PERIOD STATED ABOVE. NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR ENTITY WITH RESPECT TO THE PRODUCT SHALL BE BINDING ON DISTRIBUTOR. REPAIR, REPLACEMENT, OR REFUND OF THE ORIGINAL PURCHASE PRICE – AT DISTRIBUTOR’S SOLE DISCRETION -ARE THE EXCLUSIVE REMEDIES OF THE CONSUMER. IN NO EVENT WILL DISTRIBUTOR, ITS MANUFACTURERS, OR SAKAR INT. BE LIABLE FOR ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, BUSINESS, SAVINGS, DATA OR RECORDS) CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. EXCEPT AS STATED HEREIN, NO OTHER WARRANTIES SHALL APPLY. NOTWITHSTANDING THE FOREGOING, CONSUMER’S RECOVERY AGAINST DISTRIBUTOR SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOLD BY DISTRIBUTOR. THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL CONSUMER WHO PURCHASED THE PRODUCT AND IS NOT TRANSFERABLE.

Some countries, states or provinces do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on warranties, so limitation or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or province to province. Contact your authorized retailer to determine if another warranty applies. This product is manufactured, distributed and sold by SAKAR International, Inc. All other trademarks are the property of the respective owner, who has not sponsored, endorsed or approved this product.

Technical Support
For technical support issues please visit our website at www.vivitar.com.
You can find manuals, software and FAQ’s on the website.
Cant’t find what you are looking for?
E-mail us at support@vivitar.com and one of our technical support team members will answer your questions.
For phont support in the US please call 1-800-592-9541.

FAQS

Can outside cameras work without WiFi?

Yes, there is an outdoor security camera without wifi that functions without internet. Internet access is not always necessary for wireless security cameras. Instead, some security cameras allow for the local recording of their footage onto hard drives or micro-SD cards so that it can be watched later.

What is a Vivitar used for?

The Vivitar is a precision optical component designed to  expand your photographic capabilities. This premium quality 2x teleconverter, effectively doubles the focal length of the lens it’s used with and maintains the resolution and contrast of any fine optic.

Can you use an action camera as a normal camera?

Actions cameras are similar to how a normal digital camera functions.  You can use both for shooting pictures and recording videos. The distinctiveness between the two actually comes from the form rather than the functionality.

Do you need an SD card for action camera?

Action cameras are a great way to capture your adventures, whether you’re skiing, mountain biking, or just hanging out with your friends. But  if you want to record video, you need a memory card. The best action cam memory cards are fast, reliable, and large enough to hold many hours of video.

Can Vivitar camera be used outside?

This security camera not only monitors your personal spaces, but  can also be used outside for property surveillance.

Does the Vivitar camera have sound?

It does record sound, although you will not get studio quality with the internal mic. It also has a place for a USB to be plugged in for an external Mic.

What app does the Vivitar camera use?

The  Vivitar Smart Home Security app  lets you set up and manage your Vivitar cameras, smart lighting and electric outlets. This guide will show you how to install the app onto your phone or tablet.

Does Vivitar action cam take pictures?

Like the GoPro,  you can use the Vivitar to take photos or record video. It also has a mode for recording in the car (which seems to record upside down), and you can change settings such as resolution, and turn on or off image stabilization, slow motion, photo timer, photo burst, etc.

Does Vivitar capture cam record video?

Known for great audio and quality video, this camera is no exception.  Using a pre-formatted 32GB SD card, I managed to record 1080p video  that is probably up to Vivitar’s standards – but there is no interface software available.

Does the Vivitar camera record?

Vivitar’s DVR 786HD ActionCam  allows you to record amazing footage from your point of view! Designed with the traditional family in mind, the DVR 786HD ActionCam is one of the most versatile action cams ever made. The DVR786HD Action Cam is waterproof and includes a bike/ATV mount, so you can film all the action!

What security cameras work without a monthly fee?

Our four top-rated no-monthly-fee home security systems are  SimpliSafe, abode, Ring, and Arlo. Do no-monthly-fee security systems offer video recording? They all offer real-time viewing for free, but most require a monthly fee for video recording.

Does Vivitar camera have a flash?

The Vivitar 283 electronic flash features bounce flash for softer, more professional-quality lighting. The Auto Thyristor circuitry has a fast recycle time and a high number of flashes per set of batteries. Additional features include autocheck, a sufficient-light indicator, and an illuminated calculator dial.

Why is my Vivitar camera not working?

If your camcorder will not turn on, a good place to start is to  make sure the battery is charged. Plug your camcorder charger into an active outlet and plug the USB connector into the camera. If the display does not turn on and no charging lights activate, you will need to replace the battery.

How old is the Vivitar camera?

The Vivitar company was originally  founded in Hollywood in 1938  under the name Ponder & Best, Inc, but as a distributor, the company never manufactured cameras of its own. The name was officially changed to Vivitar in 1979, after the brand name had become prominent and successful.

References

• Vivitar Consumer Electronics Store — Vivitar.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>