home FK 415 Electric Convector Instruction Manual

home FK 415 Electric Convector

STRUCTURE

| switch off timer/window opening detection button

17

|

on / standby button

IMPORTANT SAFETY INSTRUCTIONS

WARNINGS

1. Please read and keep the following instructions before using the product. The original instructions are in Hungarian language.
2. Children under the age of 3 should be kept away from the device unless they are under constant supervision. Children over 3 years of age and under 8 years of age should only be allowed to switch the appliance on/off if it is placed and installed in its normal operating position, and they are supervised or instructed in the safe use of the appliance and understand the hazards of use.
3. This appliance should not be used by persons with reduced physical, sensory or mental capabilities, or lacking experience and knowledge, or by children aged 8 years and over, unless they are supervised or instructed in the safe use of the appliance and understand the hazards involved. Children should not play with the appliance. Children should not be allowed to clean or carry out user maintenance on the appliance unless supervised. WARNING: Some parts of this appliance may become very hot and cause burns. Special care should be taken when children and vulnerable people are present.
4. Attention! Do not use this heater in small rooms occupied by persons who are unable to leave the room independently, unless constant supervision is provided.
5. Attention! To reduce the risk of fire, keep fabrics, curtains or any other combustible material at least 1 m away from the air outlet.
6. Make sure that the device has not been damaged during transport!
7. Do not use the device if it has been dropped!
8. Do not use the device if there is visible damage!
9. Do not place in a direct corner, observe the minimum installation distances shown in Figures 2 and 3. Observe the safety regulations in force in your country!
10. The appliance is intended to be used for air heating only, not for general heating purposes.
11. Do not use where flammable vapours or explosive dust may be released! Do not use in flammable or explosive atmospheres!
12. DO NOT use near a bathtub, sink, shower, swimming pool or sauna!
13. It is STRICTLY FORBIDDEN to install and use the appliance in rooms with baths and showers (see Figure 4) in zones 0, 1.
14. All circuits in a room containing a bath or shower must be protected by one or more RCDs with a maximum rated trip current of 30 mA!
15. In rooms with baths or showers, take into account local, specific national conditions when installing the appliance.
16. The heater must be installed so that a person in the bath or shower cannot touch the switches or other controls.
17. The device must not be placed directly under a mains socket!
18. Mount the appliance on a vertical surface only!
19. When installing, take into account the material and load-bearing capacity of the wall.
20. Make sure that the heater is stable on the wall before applying power!
21. Can only be operated under constant supervision!
22. Do not operate near children without supervision!
23. Do not use the device in vehicles or in confined spaces (< 5 m2) (e.g. lifts)!
24. If you are not going to use the device for a longer period of time, switch it off and then unplug the power cord. Store the appliance in a dry, cool place.
25. Before moving the heater, always switch off the power and allow it to cool down!
26. If you notice any abnormalities (e.g. you hear an unusual noise coming from the appliance or smell a burning smell), switch it off and disconnect the power immediately.
27. Make sure that no objects or liquids enter the appliance through the openings.
28. Protect from dust, humidity, sun and direct heat!
29. Disconnect the appliance by pulling out the plug before cleaning!
30. Never touch the device or the connection cable with wet hands!
31. It should only be connected to a 230 V~ / 50 Hz grounded wall socket!
32. Unwind the connection cable completely!
33. Do not run the connecting cable through the appliance or near air inlets and outlets!
34. Do not use an extension cord or power strip to connect the appliance!
35. Position the appliance so that the plug is easily accessible and can be pulled out.
36. Route the connection cable so that it cannot be accidentally disconnected or tripped over!
37. Private use only, no industrial use allowed!
38. Due to continuous improvements, technical specifications and design are subject to change without notice.
39. The current instructions for use can be downloaded from www.somogyi.hu
40. We accept no responsibility for any printing errors and apologise for any inconvenience.

Meaning of symbol on appliance: Do not cover!
Covering the unit can cause overheating, fire or electric shock!

Caution: Risk of electric shock!
Do not attempt to disassemble of modify the unit or its accessories. In case any part is damaged, immediately power off the unit and seek the assistance of a specialist.

In the event that the power cable should become damaged, it should only be replaced by the manufacturer, its service facility or similarly qualified personnel.

STARTUP

1. Carefully remove the packaging material before use to avoid damaging the appliance or the connecting cable. Do not put the appliance into service if it is damaged in any way!
2. Remove the device from the box.
3. Screw the supplied feet to the bottom of the heater (Figure 2) using 4 small screws per foot.
4. Set them on their feet on a solid, level surface!
5. For wall use, fix the heater to the wall without the feet using the supplied long screws and plastic dowels (Figure 3).
   • For operation, the free flow of warm air must be ensured, so choose the wall mounting location according to the diagram. The appliance must not be installed directly below the mains socket!
   • For the two upper fixing points, drill two holes of the appropriate size in the wall using the supplied paper template, in a horizontal line 370 mm apart.
   • Insert the dowels into the holes, then screw the supplied long screws into the dowels so that the screw heads protrude about 2 mm from the plane of the wall.
   • Hook the two upper fixing points of the device onto the screw heads, lower them, move them slightly to the left and then lower them completely.
   • Now mark the position of the holes on the wall at the two lower fixing points.
   • Hang the device from the wall. Drill the bottom holes in the wall, insert the dowels into the holes.
   • Hang the unit back on the wall, then fix it to the wall using the two long screws at the lower fixing points.
6. The main switch of the device must be switched off!
7. Plug the device into a standard grounded wall outlet! The device is now ready for use.

CLEANING, MAINTENANCE

Cleaning the appliance may be necessary at intervals depending on the level of contamination, but at least once a month to ensure optimal performance.

1. Before cleaning, switch off the appliance and disconnect the power by pulling out the plug.
2. Allow the appliance to cool down (min. 30 minutes).
3. Clean the metal front panel and the air inlet (bottom) with a vacuum cleaner and brush.
4. Use a slightly damp cloth to clean the outside of the appliance. Do not use aggressive cleaning agents! Do not get water inside the appliance or on the electrical components!

TROUBLESHOOTING

Overheating protection may have been activated.
The overheating protection is activated frequently.| Clean the device.

DISPOSAL
Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks imposed upon the manufacturer pursuant to the relevant regulations and shall bear all associated costs arising from such.

CHARACTERISTICS

free-standing or wall-mountable radiators for heating indoor air output: 1500 W

• can be controlled remotely with free smartphone app
• IPX4 splash water protection
• freestanding or wall-mounted
• can also be used as antifreeze (7°C)
• thermostat-controlled mode 5-35°C
• electronic push buttons, digital LED display
• weekly programme, window opening detection
• 24-hour switch-off timer
• painted steel surface
• with main switch
• overheat protection
• screws, dowels for wall mounting

USE

The device can be operated with the buttons on the device or with a free smartphone app. Once connected to the network, switch on the device using the main switch (5). The display will then show “OF” (standby) or the target temperature to be reached in °C.

Manual control
If the display shows “OF”, press the button to switch on. The display shows the factory default setting, the target temperature of 22°C.
Use the arrows to set the thermostat’s target temperature between 5 and 35 °C in 1°C increments. The unit will start heating when the target temperature is at least 1°C above the current room temperature and will turn off heating when the room temperature is 1°C higher than the target temperature. A red LED (14) indicates that the heating is currently on.

To schedule or change the switch-off time, press once. The display shows 00, which you can adjust in 1-hour increments from 0 to 24 hours using the arrow keys . To reset, press or press nothing for 15 seconds. When the timer is on, the LED (13) will indicate that the timer is on and the red display will return to the target temperature. After the time has elapsed, the device switches to standby mode.

The window opening detection function is switched off by default, you can switch it on by pressing and holding the button for 5 seconds. The display will then show “FO”. Press the key to turn the function ON and the key to turn it OFF. Press the button to silence or do nothing for 15 seconds. Feedback on the on or off status of the function is available in the app. When the window is opened, if the appliance detects that the temperature has dropped by 2°C within 2 minutes, it will switch off the heating and “FO” will appear on the display. The unit will return to its pre-opening state after 10 minutes, but can be activated sooner by pressing the button.

Control with an app
The WIFI status LED (10) on the device may show the following statuses:

We recommend:

–  turn the heater off and then on

–  restart the WIFI router

–  check that a 2.4 GHz WIFI network is available

Your phone must be connected to the internet.

1. Scan the QR code with your phone (Figure 5), then download and install the “Tuya Smart” app.
2. Select the country code, then enter your mobile phone number and press “Get”.
3. Type the verification code you receive in the SMS and enter the password you want to use in the application, which should consist of numbers and letters.
4. Log in to the application: “Login”
5. Ensure that the device and smartphone are as close as possible to the wifi router and both are connected to it.
6. Add the new device to the program by pressing the “+” button.
   • The WIFI indicator on the device should flash quickly. If it is blinking slowly, press and hold the Wifi button (12) for 3 seconds and release it – the Wifi signal will then blink rapidly (EZ pairing mode).
   • The Tuya application will find the device (HOME SMART CONVECTOR), click on the “Add” button.
   • Enter the password of the 2.4 GHz WIFI network you want to use on your phone, then press “Next”.
   • When the device pairing is running, press the “Done” button.

With the smartphone app you can turn the device on/off, set the desired thermostat value, see the current room temperature, set the off timer, activate/deactivate the window opening detection, change the unit of measurement (°C/°F), set weekly programming.
In the event of a power failure, power cut or the main switch being switched off, if this is possible, the device will automatically connect to the previously set WIFI network and continue to operate according to the program set in the application.

Overheat protection switches off the appliance in the event of overheating, e.g. when covering air inlets and outlets. Switch off the power by pulling out the plug. Allow the appliance to cool down (min. 30 minutes). Check that the air inlets and outlets are clear; clean if necessary. Put the appliance back into operation. If the overheating protection is still activated, disconnect the appliance from the power supply by pulling out the plug and contact a specialist service centre.

Resetting the device to factory default
Switch off the appliance using the main switch on the side. Press and hold the button while turning on the main switch. Release the button, the device will count to 9 and reset to factory default. The display will show a target temperature of 22 °C, any WIFI pairing that may have existed previously will be cancelled. The device is not deleted from the app, it must be deleted separately.

TECHNICAL DATA

• power supply:…………………………… 230 V~ 50 Hz
• performance:…………………………… 1500 W
• IP protection: IPX4: Protected against splashing water from all directions!
• signal transmission frequency, power:. 2,4 GHz (2,401 – 2,483 GHz) <1 mW
• heater enclosure size you:…………………… 700 x 435 x 220 mm, with feet

References

• Zed d.o.o.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>