ALPENA 78540 USB Thin Beam Phone Control User Manual
- September 28, 2024
- ALPENA
Table of Contents
ALPENA 78540 USB Thin Beam Phone Control
STEP 1
CHOOSE LIGHTING STRIP MOUNTING LOCATION
Determine the installation location for the LED strip; ideal spots include
dashboard gaps,
center console, or footwell areas. Long, sweeping locations and straight
sections work
best. Avoid sharply folding the strip to prevent damage.
NOTE: Do not bend the LED strips in a radius
of less than 5/8″ (15mm) or circuit traces will
be damaged and void warranty.
STEP 2
CUTTING TO SIZE (IF REQUIRED)
Cut the strip to your desired size if needed with
scissors or side cutters as shown. Caution
once the strip is cut the extra section cannot
be added, measure twice before cutting.
STEP 3
MOUNTING THE STRIP INTO PANEL GAPS
The LED strip can be installed into panel gaps without
using the peel-and-stick tape provided. Use the supplied
tool to help with installation. Note that the strip cannot be
folded on itself or sharply bent. For other locations, you will
need to use the peel-and-stick adhesive. See Step 4 for
more information.
STEP 4
MOUNTING THE STRIP USING
PEEL-AND-STICK ADHESIVE
Grab the roll of peel-and-stick
adhesive from the box and apply
the tape to the side of the strip the
you want to mount.
STEP 5
ROUTING WIRES & POWERING UP
Run the wires so that vehicle operation
is not interfered with directly to your USB
5V or USB-C outlet. If you need USB-C
use the supplied adapter to convert the
plug to use the LED strip.
STEP 6
CONTROLLING STRIP FUNCTION
Download the “Alpena Auto” phone control with the below QR
codes for both the Apple App Store and Google Play Store.
You can also cycle through many of the functions using the button on the USB 5V plug.
WARNING: THE FAILURE TO FOLLOW THESE INSTRUCTIONS WHEN INSTALLING THE USB THIN
BEAM
– PHONE CONTROL MAY CAUSE ELECTRIC PROBLEMS IN YOUR VEHICLE WHICH COULD CAUSE
VEHICLE
DAMAGE, ELECTRICAL SYSTEM DAMAGE, FIRE, ELECTRICAL SHOCK, PERSONAL INJURY OR
DEATH.
WARNING: DO NOT LOOK DIRECTLY INTO THE USB THIN BEAM – PHONE CONTROL. DO NOT
DRIVE
OR POSITION YOUR VEHICLE NEAR ON ROAD TRAFFIC WHEN THE USB THIN BEAM – PHONE
CONTROL IS
POWERED ON – DOING SO MAY RESULT IN VISION IMPAIRMENT AND OR VEHICULAR
COLLISION. THE
INTENDED USE OF THE USB THIN BEAM – PHONE CONTROL IS TO PROVIDE EXTERIOR
AUXILIARY
LIGHTING FOR OFF ROAD USE ONLY. THIS PRODUCT IS NOT DOT APPROVED.
INSTALLATION GUIDELINE
WARNING: SAFETY GLASSES MUST BE USED WHEN INSTALLING THIS PRODUCT.
USB Thin Beam – Phone Control is an interior auxiliary light designed to
provide auxiliary lighting
while driving off road. USB Thin Beam – Phone Control has a distinct amperage
draw noted in the
installation instructions. If you are not confident in your ability to install
the USB Thin Beam – Phone Control please consult a licensed mechanic.
USB Thin Beam – Phone Control has specific voltage and amperage ratings for
power input and
amperage draw. ENSURE THESE RATINGS ARE FOLLOWED. USB Thin Beam – Phone
Control must be
installed in a properly functioning electrical system. Do not install this
product in a malfunctioning
electrical system.
Select a mounting location that will not obstruct the operation of instruments
or any vehicle functions
Clean mounting surfaces with isopropyl alcohol (70%) and wait for the surface
to dry before proceeding.
Before permanently mounting to vehicle, test fit to ensure wiring is long
enough to be safely installed
and does not obstruct any operating functions of the vehicle. These lights
should not be installed
where their operation hinders the visibility of the driver or other drivers.
WARNING: DURING OPERATION LIGHTING UNITS CAN GET HOT – DO NOT TOUCH WHILE
OPERATIONAL OR WITHIN 30 MINUTES OF POWERING DOWN.
Before disconnecting battery terminals, please check your owner’s manual for
proper procedure
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
ALPENA® LIMITED WARRANTY
This Limited Warranty covers defects in materials or workmanship of this
product for one (1) year from the
date of purchase. Normal wear and tear over time are not product defects.
Product problems caused by
not following the product instructions, abuse, misuse, alteration, accident
and/or use beyond the product’s
intended purpose are not covered. This warranty is valid for the original
owner and is not transferable.
Proof of purchase is required.
Any implied warranties and conditions, such as merchantability and fitness for
a particular purpose are
hereby excluded, or if not excludable under law, are limited to one (1) year
period. Some jurisdictions do
not allow limitations on how long an implied warranty lasts, so this
limitation may not apply to you
NO INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARE RECOVERABLE. SOME
JURISDICTIONS DO
NOT ALLOW THE EXCLUSION OF INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, SO
THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS
AND YOU MAY HAVE OTHER RIGHTS WHICH VARY DEPENDING ON THE JURISDICTION.
We will replace any product we determine to be defective provided you follow
our product return directions.
Please note that replacement product may not be exact due to style changes to
our products. We will cover
the mailing expense to send you a replacement product. However, mailing costs
to return to us the original
product which is claimed to be defective must be paid by you. If a replacement
product is not available at
the time you submit your warranty request, we will issue a credit.
For warranty service, please see below.
Problems? We can solve them!
Federal Communications Commission (FCC) Interference Statement
FCC ID: 2AMN5-78540
This equipment has been tested and found to comply with the limits for a Class
B digital device, under
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and
used by the instructions, may cause harmful interference to radio
communications.
There is no guarantee that interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and the receiver
– Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected
– Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance
could void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The equipment must not be co-located or operating in conjunction with any
other antenna or transmitter.
Marklyn Group Inc. 753011 2nd line EHS Mono, ON, Canada L9W 5W4
Alpena® is a registered trademark of Marklyn Group Inc. © Copyright 2024
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>