BOSCH PBH 2000 RE Rotary Hammer Drill Instruction Manual

: September 28, 2024
: Bosch

Table of Contents

BOSCH PBH 2000 RE Rotary Hammer Drill
Specifications
Product Information
FAQ
Safety instructions
Product Description and Specifications
Assembly
Operation
Practical Advice
Maintenance and Service
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOSCH PBH 2000 RE Rotary Hammer Drill

Specifications

Brand: Bosch Power Tools GmbH
Model: PBH 2000 RE, PBH 2100 RE, PBH 2100 SRE, PBH 2500 RE, PBH 2500 SRE
Country of Origin : Germany
Website: www.bosch-pt.com

Product Information

The Bosch Power Tools are designed to provide efficient drilling and hammering capabilities for various applications. The models PBH 2000 RE, PBH 2100 RE, PBH 2100 SRE, PBH 2500 RE, and PBH 2500 SRE offer a range of features suitable for DIY enthusiasts and professionals alike.

FAQ

Q : Can I use the power tool without the additional handle?
A: It is recommended to always use the power tool with the additional handle for increased safety and control.
Q: How often should I replace the chuck?
A : The chuck replacement frequency depends on usage. Consider replacing it if you notice any signs of wear or reduced performance.

Safety instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from the frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Hammer Safety Warnings
Safety instructions for all operations

Wear ear protectors. Noise exposure can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring or its own cord. Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits with rotary hammers

Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend, causing breakage or loss of control, resulting in personal injury.

Additional safety information

Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to an explosion. Penetrating a water line causes property damage or may cause an electric shock.
Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool.
Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more securely than by hand.

Products sold in GB only:
Your product is fitted with a BS 1363/A approved electric plug with an internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a main socket elsewhere.

Do not touch any application tools or adjacent housing components shortly after the operation. These can become very hot during operation and cause burns.
The application tool may jam during drilling. Make sure you have a stable footing and hold the power tool firmly with both hands. Otherwise, you could lose control of the power tool.
Take care when carrying out demolition work using the chisel. Falling fragments of the demolition material could injure you or any bystanders.

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.
Please observe the illustrations at the beginning of this operating manual.

Intended Use
The power tool is intended for hammer drilling in concrete, brick and stone, as well as for light chiselling work. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. Power tools with electronic control and right/left rotation are also suitable for screwdriving.

Product Features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

Keyless chuck (PBH 2500 SRE)a)
SDS plus drill chuck
SDS plus tool holder
Dust protection cap
Locking sleeve
Handle (insulated gripping surface)
Rotational direction switch
Lock-on button for on/off switch
On/off switch
Impact/mode selector switch
Button for depth stop adjustment
The wing bolt of the auxiliary handle
Auxiliary handle (insulated gripping surface)
Depth stop
Securing screw for keyed chuck)
Keyed chuck (PBH 2100 SRE, PBH 2500 SRE)a)
SDS plus shank for drill chucks)
Saugfix suction openings)
Saugfix clamping screw)
Saugfix depth stopa)
Saugfix telescopic tubea)
Saugfix wing bolt)
Saugfix guide tubes)
Universal holder with SDS plus Shanka)

This accessory is not part of the standard scope of delivery.

Technical Data

A) This accessory is not available in every country.
B) Weight without mains connection cable and without mains plug

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Values can vary depending on the product, scope of application, and environmental conditions. To find out more, visit www.bosch- professional.com/wac.

Noise/Vibration Information

The vibration level and noise emission value given in these instructions have been measured under a standardized measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.
The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different accessories or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not being used should also be taken into account.
This may significantly reduce vibration and noise emissions over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and accessories, keeping their hands warm, and organising workflows correctly.

Assembly

Pull the plug out of the socket before carrying out any work on the power tool.

Auxiliary handle

Do not operate your power tool without the auxiliary handle (13).
Make sure that the auxiliary handle is always tightened. Otherwise, you could lose control of the power tool when working.

Swivelling the auxiliary handle (see Figure A)
You can swivel the auxiliary handle (13) to any angle for a safe work posture that minimizes fatigue.

Loosen the wing bolt (12) of the auxiliary handle (13) and adjust the auxiliary handle (13) to the required position.
Then retighten the wing bolt (12) of the auxiliary handle (13).
Make sure that the clamping ring of the auxiliary handle slots into the corresponding groove on the housing.

Selecting drill chucks and tools
For hammer drilling and chiselling, you will need SDS plus tools, which insert into the SDS plus drill chuck.
For drilling without impact in wood, metal, ceramic, and plastic as well as for screwdriving, tools without SDS plus are used (e.g. cylindrical shank drill bits). For these tools, a keyless chuck or a keyed chuck are required.

Changing the drill chuck
Inserting/removing the keyed chuck

PBH 2100 SRE/PBH 2500 SRE
You must use a suitable drill chuck (keyed or keyless chuck, accessories) to work with tools that do not have SDS plus (e.g. cylindrical shank drill bits).

Fitting the keyed chuck (see Figure B)

Screw the SDS plus shank (17) into a keyed chuck (16).
Secure the keyed chuck (16) using the securing screw (15). Note that the securing screw has a left-hand thread.

Inserting the keyed chuck (see Figure B)

Clean and lightly grease the insertion end of the shank.
Insert the keyed chuck with the adapter shank into the tool holder with a turning motion until it automatically locks.
Check that it is locked by pulling the keyed chuck.

Removing the keyed chuck

Push the locking sleeve (5) back and remove the keyed chuck (16).

Inserting/Removing the Keyless Chuck PBH 2500 SRE
Inserting the keyless chuck (see Figure C)

Clean and lightly grease the insertion end of the shank.
Insert the keyless chuck (1) with the shank into the tool holder while turning it until it locks automatically.
Check that it is locked by pulling the keyless chuck.

Removing the Keyless Chuck

Push the locking sleeve (5) back and remove the keyless chuck (1).

Changing the Tool

The dust protection cap (4) largely prevents the penetration of drilling dust into the tool holder during operation. When inserting the tool, make sure that the dust protection cap (4) does not become damaged.

Replace a damaged dust protection cap immediately. It is recommended that you use an after-sales service for this.

Changing the Tool SDS plus

Inserting the SDS plus Application Tool (see Figure D)
The SDS plus drill chuck (2) enables you to change the application tool easily and conveniently without needing to use additional tools.
Clean and lightly grease the shank of the application tool.
Insert the application tool into the tool holder (3) while turning it until it locks automatically.
Check that it is locked by pulling on the tool.
As a requirement of the system, the SDS plus application tool can move freely. This causes a certain radial run-out at no-load, which has no effect on the accuracy of the drill hole, as the drill bit centres itself upon drilling.

Removing the SDS plus Application Tool (see Figure E)

Push the locking sleeve (5) back and remove the application tool.

Changing the keyed chuck

PBH 2100 SRE/PBH 2500 SRE Inserting the application tool
Note: Application tools that do not have SDS plus must not be used for hammer drilling or chiselling. Tools without SDS plus and their drill chucks are damaged by hammer drilling or chiselling.

Insert a keyed chuck (16).
Open the keyed chuck (16) by turning it until the tool can be inserted. Insert the tool.
Insert the chuck key into the corresponding holes of the keyed chuck (16) and clamp the tool evenly.
Turn the impact/mode selector switch (10) to the “drilling” position.

Removing the application tool

Use the chuck key to turn the sleeve of the keyed chuck (16) anticlockwise until the application tool can be removed.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reactions and/or cause respiratory illnesses in the user or in people in the near vicinity.
Certain dust, such as oak or beech dust, are classified as carcinogenic, especially in conjunction with wood treatment additives (chromate, wood preservative). Materials containing asbestos may only be machined by specialists.
Use a dust extraction system that is suitable for the material wherever possible.
Provide good ventilation at the workplace.
It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can easily ignite.

Dust extraction with the dust extraction attachment (accessory)

Fitting the dust extraction attachment (see Figure F)
For dust extraction, the dust extraction attachment (accessory) is required. When drilling, the dust extraction attachment retracts so that the attachment head is always close to the surface at the drill hole.
Press the button for depth stop adjustment (11) and remove the depth stop (14). Press the button (11) again and insert the dust extraction attachment into the auxiliary handle (13) from the front.
Connect an extraction hose (diameter 19 mm, accessory) to the suction opening (18) of the dust extraction attachment.
The dust extractor must be suitable for the material being worked.
When extracting dust that is dry, especially detrimental to health or carcinogenic, use a special dust extractor.

Setting the drilling depth on the dust extraction attachment (see Figure G) You can also set the required drilling depth X when the Saugfix is fitted.

Push the SDS plus application tool into the SDS plus tool holder (3) as far as it will go. Otherwise, the movability of the SDS plus drilling tool can lead to incorrect adjustment of the drilling depth.
Loosen the wing bolt (22) on the Saugfix.
Without switching it on, press the power tool firmly against the surface you wish to drill. The SDS plus application tool must be touching the surface.
Slide the guide tube (23) of the Saugfix into its holder so that the head of the Saugfix rests on the surface that is to be drilled. Do not slide the guide tube (23) further than necessary over the telescopic tube (21), so that as much as possible of the scale remains visible on the telescopic tube (21).
Retighten the wing bolt (22). Loosen the clamping screw (19) on the Saugfix depth stop.
Slide the depth stop (20) onto the telescopic tube (21) so that the distance X shown in the illustration matches your required drilling depth.
Tighten the clamping screw (19) in this position

Operation

Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Start-up

Pay attention to the mains voltage. The voltage of the power source must match the voltage specified on the rating plate of the power tool.

Setting the Operating Mode The operating mode of the power tool is selected using the impact/mode selector switch (10).

To change the operating mode, turn the impact/mode selector switch (10) to the required position.

Note: Only change the operating mode when the power tool is switched off. Otherwise, the power tool may become damaged.

Position for hammer drilling into concrete or stone
Position for drilling without impact in wood, metal, ceramic and plastic and for screwdriving
Vario-Lock position for adjusting the chisel position The impact/mode selector switch (10) will not engage in this position.
Position for chiselling

Setting the rotational direction (see Figure H)

The rotational direction switch (7) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (9) is being pressed

Only operate the rotational direction switch (7) when the power tool is not in use.

Always set the rotational direction to clockwise rotation for hammer drilling, drilling and chiselling.

Clockwise: To drill and drive in screws, press the rotational direction switch (7) all the way to the left.
Anticlockwise : To loosen and unscrew screws and nuts, press the rotational direction switch (7) all the way to the right.

Switching On/Off

To switch on the power tool, press the on/off switch (9).
To lock the on/off switch (9), press and hold it while also pushing the lock-on button (8).
To switch off the power tool, release the on/off switch (9). If the on/off switch (9) is locked, press the switch first and then release it

Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when it is on by pressing in the on/off switch (9) to varying extents. Applying light pressure to the on/off switch (9) results in a low rotational speed/impact rate. Applying increasing pressure to the switch increases the speed/impact rate

Changing the chiselling position (Vario-Lock)
You can lock the chisel in 36 different positions, so you can select the optimum working position for each task.

Insert the chisel into the tool holder.
Turn the impact/mode selector switch (10) to the “Vario- Lock” position.
Turn the application tool to the required chisel position.
Turn the impact/mode selector switch (10) to the “chiselling” position. With this, the tool holder is locked.
Set the rotational direction for chiselling to clockwise

Practical Advice

Setting the drilling depth (see figure I)

You can use the depth stop (14) to set the required drilling depth X.

Press the button for depth stop adjustment (11) and insert the depth stop into the auxiliary handle (13). The fluting on the depth stop (14) must face downwards.
Push the SDS plus application tool into the SDS plus tool holder (3) as far as it will go. Otherwise, the movability of the SDS plus drilling tool can lead to incorrect adjustment of the drilling depth.
Pull the depth stop far enough out that the distance between the drill bit tip and the edge of the depth stop corresponds to the required drilling depth X.

Overload clutch

If the application tool jams or snags, the power transmission to the drill spindle will be interrupted. Always hold the power tool firmly with both hands to withstand the forces this may create and adopt a position with stable footing.
Switch the power tool off immediately and remove the application tool if the power tool becomes blocked. Switching on when the drilling tool is blocked may cause high torque reactions.

Inserting screwdriver bits (see figure J)

A universal holder (24) with SDS plus shank (accessory) is required to work with screwdriver bits.

Clean and lightly grease the insertion end of the shank.
Insert the universal holder into the tool holder while turning it until it locks automatically.
Check that it is locked by pulling the universal holder.
Insert a screwdriver bit in the universal holder. Only use screwdriver bits that fit the screw head.
To remove the universal holder, slide the locking sleeve (5) backwards and remove the universal holder (24) from the tool holder
Only apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any work on the power tool.
To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean. In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service centre that is authorised to repair Bosch power tools.
Replace a damaged dust protection cap immediately. It is recommended that you use an after-sales service for this.
Clean the tool holder (3) after each use

You can find further service addresses at:
www.bosch-pt.com/serviceaddresses

Disposal

The power tool, accessories and packaging should be recycled in an environmentally friendly manner. Do not dispose of power tools along with household waste.

Only for EU countries:
Power tools that are no longer suitable for use must be disposed of separately. Use the designated collection systems. If disposed of incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for the United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner

parts

EU Declaration of Conformity

Rotary Hammer Article numberWe declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards. Technical file at:

Declaration of Conformity

CONTACT

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning the maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com