ADAM MODEL A 5 In 1 Wireless Charging Station User Manual

MODEL A
5-in-1 Wireless Charging Station
User Manual

Specification

to 7.5W)
• AirPods Charging Base: 5V/5W
• Apple Watch Charger: 5V/2.5W
Operating Temperature| 0°C – 40°C
Size| 156 x 134 x 75 mm
Weight| 280 g
3-Year Limited Warranty

Protective Function

| Multiple Circuit Protection
---|---
| Over-Heat Protection
| Short-Circuit Protection
| Over-Voltage Protection
| Over-Current Protection
| Flame Retardant Protection

Attention

| Do not disassemble, puncture, drop, bend or modify
---|---
| Do not shake while charging
| Unplug the device when fully charged
| Do not expose to liquids
| Keep away from children
| Avoid extreme temperatures
| 3-year limited warranty
| For the fastest and safest charge, use an ADAM cable, your device’s original cable or a certified cable (such as MFi)
| Please scan the QR code on the packaging for the user manual

Product Introduction

Instructions for use

1. Turn on the machine, the ice blue light comes on, and the coil motor resets;
2. Wireless charging
   (1). Wireless charging of mobile phones – Place the phone with wireless charging support on the wireless charging platiorm for coil
   inspection, recognition, and movement scanning. The scan will move according to the center position of the phone’s coil to find the
   best charging alignment.
   After alignment, it will stop, and the phone will enter rapid charging wirelessly. At the same time, the tail light will switch to a green ligh(2). Watch charging – Place the wireless charging watch on a designated watch charging platform for wireless charging.
   (3). Headphone charging – Place the wireless charging platiorm that supports wireless charging headphones in the product seat,
   recognize the charging of the headphones, and convert the tail light into a blue light.
   (4). When the phone and earphones are placed for wireless charging at the same time, the tail light will switch to a purple light (note:
   there is no light conversion during watch charging)

Rear ambient light

By default, the ice blue light will remain on when powered on. Press the light control switch once to switch to green light, press twice to switch to blue, press once again to switch to purple, press the fourth time to turn off the light, and press the fifth time to turn on the ice blue light again, and cycle in this order.

• Photosensitive sensing
  The brightness of the Nixie tube display screen changes with the ambient light brightness. When the ambient light becomes bright, the display screen also becomes bright, and when the ambient light edge is dark, the display screen also becomes dark.

Time settng: (only adjust hours/minutes)

(1). Double click and press the “left” button twice to enter the time seting mode, and the ten digits of the hour will start flashing.
(2). Short press the “right” button, add 1 to the number, and if the number is greater than 2, return to 0, and cycle like this.
(3). If any number flashes for more than 10 seconds without any key operation, the seting will be cancelled and the current setingdata will be invalid. If any key has been pressed, the timing will be reset.
(4). If in settng mode, press the “left” button again to enter the next digit seting; When both the hour and minute numbers have been set, a long sound of “drip” will sound. This indicates that the time seting was successful.

Alarm setings: (divided into single alarm and circular alarm setings)

A. Single alarm setting

1. Double click and press the “right” button twice to enter the single alarm setting mode. The alarm icon will start flashing at the tenth digit of the hour.
2. Short press the “left” button, add 1 to the number, and if the number is greater than 2, return to O, and cycle like this.
3. If any number flashes for more than 10 seconds without any key operation, the setting will be cancelled and the current setting data will be invalid. If any key has been pressed, the timing will be reset.
4. If in setting mode, press the “right” button again to enter the next digit setting; When both the hour and minute numbers have been set, a long sound of “drip” will sound. This indicates that the alarm clock has been successfully set.

B. Loop alarm settings

1. Long press and hold the “right” button to enter the circular alarm setting mode. The tenth digit of the hour will start flashing and the alarm icon will light up.
2. Short press the “Left” key, “Number plus 1. If the number is greater than 2, return to O, and cycle like this.
3. If any number flashes for more than 10 seconds without any key operation, the setting will be cancelled and the current setting data will be invalid. If any key has been pressed, the timing will be reset.
4. If in setting mode, press the “right” button again to enter the next digit setting; When both the hour and minute numbers have been set, a long sound of “drip” will sound. This indicates that the circular alarm clock has been successfully set.

FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Alarm clear:

Long press and hold the “left” button to clear all alarm data from the memory (including single alarm and circular alarm). If there is an alarm icon displayed, clear the icon display.
Note : If the alarm clock is activated, the snooze seting will also be cleared.

Charging prompt sound:

1. Press and hold the ambient taillight adjustment button until a long “beep” sounds. This means the charging beep is turned off.
2. Press and hold the ambient taillight adjustment button until a short beep of “beep-” sounds. This means the charging beep is on.

Other functions

A. Alarm clock

1. When the time of a single alarm clock reaches, the alarm clock icon remains on, and the buzzer emits “beep, beep, beep, beep””beep, beep, beep, beep…” intermittently. After 1 minute, the beep will automatically stop and the alarm clock icon will go out.
   If any button is pressed during the alarm clock period, it will immediately end.

2. After the alarm clock ends, the data of a single alarm clock will be cleared from the memory, and no alarm action will be generated again.

3. When the time for the circular alarm clock reaches, the alarm clock icon remains on, and the buzzer intermittently emits “beep, beep, beep, beep, beep, beep”… After 1 minute, the beep will automatically stop. If any button is pressed during the alarm clock
   period, it will immediately end.

4. After the alarm clock ends, the data of the circular alarm clock will be retained in the memory, that is, when the next time comes, the alarm clock action will still be generated.

5. Whether it is a single alarm or a circular alarm, as long as there is an alarm setting in the memory, the alarm icon will always be displayed on the screen, unless the alarm setting is cleared or only a single alarm is set, and the single alarm has ended.

Attention : Please use the input chargers 5V/3A and 9V/2A that support protocol fast charging chargers correctly. Using a charging adapter that is lower than 5V/3A or does not support fast charging protocol may cause slow charging, disconnection, and other situations.

ADAM elements International Co., Ltd.
www.adamelements.com
support@adamelements.com
+886-2-2738-9900 https://store.adamelements.com/

FCC ID: 2ABY9MODEL-A CCAB24LP0350T6

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>