ROLLASHADE 4 Inch Contract Plus 4 Top Fascia Installation Guide
- September 27, 2024
- Rollashade
Table of Contents
- 4 Inch Contract Plus 4 Top Fascia
- Specifications
- Product Usage Instructions
- 1. Inside or Outside Application
- 2. Install Fascia into Brackets
- 3. Mounting Location
- 4. Screw Installation
- 5. Alignment
- 6. Shade Pin End Installation
- 7. Motor End Installation
- 8. Lock Ring
- 9. Plug In Motor
- 10. Shade Adjusting (If Necessary)
- 11. Adjusting Limits (If Necessary)
- Q: Can I install the shades outside?
- Q: What tools do I need for installation?
- Q: How do I know if my brackets are properly aligned?
4 Inch Contract Plus 4 Top Fascia
“`html
Specifications
-
Product Name: CONTRACT PLUS+ 4 TOP FASCIA
-
Hardware Included: Bracket Covers, Motor Bracket, Motor Bracket
Idler End, #14 Screw Screws, Shades + Motors, Fascia, Zip Ties,
Wire Tie Pads, Wall Switch, Switch Box -
Tools Required: 3/8 Hex Head, Phillips Head, 1/8 Drill Bit,
Drill -
Installation: Inside or Outside Application
Product Usage Instructions
1. Inside or Outside Application
All shades may be pre-programmed to sensors, remotes, and/or
wall switches upon arrival. Determine whether you are installing
the shades inside or outside.
2. Install Fascia into Brackets
Put fascia in place for both motor and idle end brackets
according to the provided instructions.
3. Mounting Location
Position your brackets and fascia in the chosen mounting
location for inside or outside mount as per the provided
guidelines.
4. Screw Installation
Mark screw holes, pre-drill using a 1/8 drill bit, and then
install the brackets & fascia with the provided screws using a
1/4 hex head driver.
5. Alignment
Ensure that your brackets are level and properly aligned.
6. Shade Pin End Installation
Align the swivel ball bearing with the idler shaft for easy
installation. Press the idler shaft all the way to the bracket.
7. Motor End Installation
Remove the locking ring, line up the motor bracket, and push the
motor into the motor bracket.
8. Lock Ring
Add the locking ring to the motor bracket to secure the motor
correctly.
9. Plug In Motor
Plug in the motor ensuring compliance with city/state code
requirements.
10. Shade Adjusting (If Necessary)
If needed, adjust the shade by guiding it in the desired
tracking direction until it rolls up straight.
11. Adjusting Limits (If Necessary)
Refer to the programming instructions based on the motor used
for your application to adjust limits if necessary.
Frequently Asked Questions (FAQ)
Q: Can I install the shades outside?
A: Yes, there are instructions provided for both inside and
outside mounting applications.
Q: What tools do I need for installation?
A: You will need a 3/8 Hex Head, Phillips Head screwdriver, 1/8
Drill Bit, and a Drill.
Q: How do I know if my brackets are properly aligned?
A: Check that the brackets are level and aligned according to
the provided guidelines.
“`
CONTRACT PLUS+ 4″ TOP FASCIA
INSTALL ATION INSTRUCTIONS
Rollashade.com info@rollashade.com 951.245.5077
© Copyright Roll-A-Shade® Inc. All Rights Reserved.
HARDWARE INCLUDED
Bracket Covers
Motor Bracket
Motor Bracket Idler End
14 Screw Screws
Shades + Motors
Fascia
Shade 1 Shade 2 Shade 3
STOP
Zip Ties
Wire Tie Pads Wall Switch Switch Box
TOOLS REQUIRED 3/8″ Hex Head Phillips Head 1/8″ Drill Bit
Drill
1 INSIDE OR OUTSIDE APPLICATION NOTE: ALL SHADES MAY BE PRE-PROGRAMMED TO
SENSORS, REMOTES, AND/OR WALL SWITCHES UPON ARRIVAL
OUTSIDE
INSIDE
INSIDE
OUTSIDE
RASCP4TMVER.2 2 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
2 INSTALL FASCIA INTO BRACKETS Put fascia in place for both motor and idle end brackets.
A
B
C
D
E
3 MOUNTING LOCATION Place your brackets and fascia, (bracket covers optional), in its mounting location for inside or outside mount.
A OUTSIDE MOUNT
B INSIDE MOUNT
RASCP4TMVER.2 3 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
4 SCREW INSTALLATION
Mark your screw holes. Next, pre-drill your screw holes using a 1/8″ drill
bit. Install the brackets & fascia with the provided screws using the 1/4″ hex
head driver.
5 ALIGNMENT Check to make sure your brackets are level and aligned.
6 SHADE PIN END INSTALLATION
Swivel ball bearing to align with idler shaft for easy installation. Press idler shaft all the way to the bracket.
A
B
RASCP4TMVER.2 4 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
7 MOTOR END INSTALLATION
Remove locking ring. Lineup to motor bracket. Push motor into motor bracket.
A
B
8 LOCK RING
Add locking ring to motor bracket. Check motor is secured correctly.
A
B
9 PLUG IN MOTOR
· Run motor power cord to nearest power outlet. · Install wire tie pads and
secure with zip ties to hold wire down. · The path of the wire should be
parallel with mullions and/or drop ceiling tiles
ensuring the cable is neatly organized. · Any modifications to the power cable
should be done by a certified electrician to
meet your city/state code requirements.
10 SHADE ADJUSTING (IF NECESSARY)
· Roll shade up and down to confirm hembar is level and material rolls up
straight on center tube.
· If the hembar is not level, lower shade until you see the metal tube. · Add
layers of masking tape to the metal tube to the end that is too low until
hembar
is straight. · If the material tracks to one side, lower shade until you see
the metal tube. · Add layers of masking tape to the metal tube to the end that
is opposite the
direction of tracking, until shade rolls up straight.
RASCP4TMVER.2 5 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
11 ADJUSTING LIMITS (IF NECESSARY) See programming instructions based on the
motor used for your application.
RASCP4TMVER.2 6 OF 6 | © Copyright Roll-A-Shade® Inc. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>