Force1 RC Obiter Extreme RC Aerial Drone With 360 Spins Instruction Manual

Force1 RC Obiter Extreme RC Aerial Drone With 360 Spins

Frequently Asked Questions

Q: Is this drone suitable for beginners?

A: The drone is suitable for experienced RC drone users aged years or above. It is not recommended for users under years.

Q: What should I do if my drone LED light flashes?

A: If your drone LED light flashes, it might indicate low battery. Recharge the drone to resolve this issue.

Q: Can I use non-genuine parts and accessories with this drone?

A: Force does not assume any responsibility for accidents caused by using non- genuine parts. It is recommended to use genuine parts and accessories for optimal performance and safety.

PARTS LIST

Product specifications

DRONE INTRODUCTION

Drone Parts Introduction

REMOTE CONTROL

Remote Control Functions

Remote Control Batteries Installation

How to install the battery: Open the battery cover on the back of the remote control, and correctly install the 4 AAA alkaline batteries according to the electrode instructions on the battery box. (Batteries not included)

LITHIUM BATTERY CHARGING INSTRUCTION

Charging With The USB Charging Cable

1. Press and pull to take out the battery.
2. Plug USB into power source and then into the drone. Red indicator will light while charging. Red light will turn off after fully charged.

Charging time is about 60-80 minutes and flight time is approx imately 5-6 minutes.

OPERATING INSTRUCTIONS

Boot Program

1. Insert the battery into the battery compartment. Then press the power button on the drone. The LED light will flash, put the drone on a flat surface.

2. Power on the remote, it will beep. The the remote control indicator light will flash red and the drone LED lights will flash as well.

3. The 2.4ghz pairing between the remote and drone. Push the left joystick up (remote will beep, indicator light flashes red and drone led lights flash). Push the joystick down, the remote will beep and the red light will turn solid. The pairing is complete!

4. Gyroscope Calibration Push the left and right joysticks to the lower inner corners (as shown in the picture above) and release them at the same time. The blades will rotate at a low speed. The drone lights will stop flashing and turn solid. Calibration is successful and the motors will start!

5. Push the left joystick upward or press the one-key takeoff button; the drone will take off.button; the drone taking off.

Before taking off, please be sure to put the drone on a horizontal surface and calibrate it to ensure that the drone flies smoothly after takeoff.
When the drone is hit or involved in a crash, use gyroscope calibration to correct the flight.

OPERATION AND CONTROL

Speed Selection

Press the upper left button to select a different speed. Each time it’s pressed the drone will move to a different speed (low, med or high) and the remote will beep.

• beep = low speed
• beeps = medium speed
• beeps = high speed

Basic Action Operation Methods

For beginners, it is recommended to operate the joystick slowly to avoid damaging the drone due to excessive movements.

• When the left joystick (throttle) is pushed up or down, the drone will fly up or down accordingly.

• When the left joystick (throttle) is pushed left or right, the drone will turn left or right accordingly.

• When the right joystick (direction) is pushed up or down, the drone will move forward or backward accordingly.

• When the right joystick (direction) is pushed left or right, the drone will fly left or right accordingly.

Trimming

Press the button on the upper right corner of the remote control. The remote control will beep twice and enter trimming mode.

• When the drone deviates forward, move the right joystick backward (the remote control indicator light 1 flashes red)
• When the drone deviates backward, move the right joystick forward (the remote control indicator light 1 flashes red)
• When the drone deviates to the left, move the right joystick to the right (the remote control indicator light 1 flashes red)
• When the drone deviates to the right, move the right joystick to the left (the remote control indicator light 1 flashes red)
• After the drone offset adjustment is completed, you can press the button on the upper right corner of the remote control again. The remote control will “beep” to exit the trimming mode, or if you do not move the right joystick for ? second, the trimming mode will automatically exit.

HOW TO OPERATE STUNTS

Tip: The following stunt actions can only be performed when the Drone is at least 1 meter ( 3.2′ ft / 39.3.” in ) above the ground!

One Key Shifting To Vertical Led Ring

For beginners, it is recommended to operate the joystick slowly to avoid damaging the drone due to excessive movements.

Tornado Spinning With Orbital Running

During flight, when you press and hold the button on the top right corner of the remote, the remote will beep. The LED ring will spin and drone will go 360 around.

Tornado Spinning

During flight, when you press the tornado spinning button, the remote will beep and the drones LED ring will start spinning.

Vertical Orbital Running

During the flight, press and hold the button on the upper left corner of the controller. The controller makes a”beep” sound, the drone’s LED ring will rotate from the horizontal to the vertical and orbital running.
Push “UP/DOWN” button to adjust drone’s flying height.
When you press and hold the button in the upper left corner of the remote control again, the remote control makes a beep and the drone will be back to horizonal.

FLIGHT ENVIRONMENT

Avoid accidental injury or damage to the drone caused by flying the drone in these environments.

BLADE INSTALLATION

When a blade is damaged, it needs to be replaced if it’s impacting flight.
There are position requirements for the installation of the drone’s blades. The letters engraved on the blades must correspond to the letters engraved on the drone frame. That is, “A” corresponds to “A” and “B” corresponds to “B”, otherwise the drone cannot take off normally.

Installation of the blade: Hold the cap of the blade, align it with the motor shaft, and press it into place. Note that the blades cannot be deformed.

TROUBLESHOOTING

WARNING

Please read the instructions carefully before using this product and keep them properly for future reference. Our company and the seller are not responsible for any losses or personal injuries caused by improper operation or improper use of this product.

IMPORTANT STATEMENT

Thank you for buying a Force 1 drone. Please read this manual carefully before operating the drone. Your purchase implies you have read this and agree to follow all guidelines and instructions herein.

1. Please operate in a safe manner. We undertake no liability for human injury or property damage caused by improper operation, as we have no control over setup, use and operation of this drone.

2. This drone is suitable for experienced RC drone users aged 8 years or above. Not safe for
   users under the age of 8 to use.

3. The flying field must be legally approved by your local government.
   Force 1 does not assume any responsibility for any accidents caused by using non-genuine parts and accessories. Keep the packaging and user manual for future reference.
   Email us at support@force1rc.com for questions, comments or to request spare parts.

SAFETY PRECAUTIONS

This drone is suitable for experienced drone users aged 8 years and above. This product contains small parts; please keep out of reach of small children

1. Keep away from humid environment The drone is made of a precise electronic component. Humidity or water vapor
   may damage electrical components causing accidents.

2. Keep away from rotating parts Rotating parts can cause serious injury and damage. Keep face and body away from rotating motors. Tie hair back, wear a hat or hood to avoid entanglement and injury.

3. Keep away from heat
   The drone is made of metal fiber, plastic, electronic components, etc. Keep away from heat and direct sunlight to avoid distortion and damage.

4. Stay aware while operating this drone Avoid areas with sudden changes in elevation, uneven ground or dangerous obstacles. For indoor use only, flying outdoors can result in a lost drone.

www.force1rc.com
For fast, friendly service please contact us at support@force1rc.com

References

• Robinson+Cole

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>