Estia Homeart 06-21146 Aither Floor Stand Fan Aither Instruction Manual

: September 23, 2024
: Estia Homeart

Table of Contents

ATTENTION
IMPORTANT SAFEGUARDS
FAN PARTS
ASSEMBLY
OPERATION
CARE AND CLEANING
FAN STORAGE
TECHNICAL INFORMATION
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Estia Homeart 06-21146 Aither Floor Stand Fan Aither

ATTENTION

Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this appliance to other people, please also pass on the operating instructions.

IMPORTANT SAFEGUARDS

When using electrical appliance, basic precautions should be followed to reduce the risk of fire and personal injury.

Always operate the product from a power source of the same voltage, frequency and rating as indicated on the product identification plate.
Do not use this fan with any solid-state speed control device to reduce the risk of electric shock.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Cleaning and user maintenance shall not be made by children without supervision.
The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. Do not leave the fan running unattended.
Do not operate the product if it is dropped, damaged or showing signs of product malfunction. Do not operate the product with a damaged plug or cord. If it is not working properly, contact a qualified electrician or service center for examination and repair, never try to dismantle it by yourself.
Do not immerse or expose the product or flexible cord to rain, moisture or any other liquid.
This product should not be used near water, such as bathtubs, washbowls, swimming pools etc. where the likelihood of immersion or splashing could occur.
Never install the unit where it could be subject to:
a. Heat sources such as radiators, stoves or other products that produce heat;
b. Direct sunlight;
c. Excessive dust;
d. Lack of ventilation, such as a cabinet or bookcase;
e. Uneven surface;
Switch off and unplug from the outlet when the product is not in use, before assembling or disassembling parts and before cleaning. Fully assemble the fan before switching it on.
Avoid contact with moving parts. Do not insert any body parts (e.g. finger) or objects through the grill when the fan is operating.
Do not cover the grille, or operate near curtains, etc.
This product is intended for normal domestic/household use only.
Always disconnect the fan when moving it from one location to another.
The use of attachments or accessories not recommended or sold by the product distributor may cause personal or property hazards or injuries.
Be sure the fan is on a stable surface when operating to avoid overturning.
Do not immerse in water.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person, to avoid a hazard.

FAN PARTS

ASSEMBLY

Loosen the blade cap by turning clockwise and rear guard mounting nut by turning anti- clockwise. (Fig1).
Put rear grille on motor shaft and secure with rear mounting nut. (Fig2).
Slide blade on motor shaft and secure with blade cap by turning anti-clockwise. (Fig3 and Fig 4).
Put front grille on rear grille and close clips, and then fix together with screw and nut provided.(Fig5).
Loosen the base screw by turning anti-clockwise from the base pipe, and insert the base pipe to the base, put the base screw through the base pipe by turning clockwise then tighten the base pipe and the base.
Put the base cap on the base, pull the inner pipe out then tighten the lock nut again.
Loosen the control box screw (screw B) by turning counter clockwise, insert the control box firmly down the inner pipe, and screw the control box screw by turning clockwise.

OPERATION

Set the fan on a dry, level surface.
Plug the cord into any standard 220-240V AC outlet.
To turn the fan on rotate the speed switch to marked (1) low, (2) medium, or (3) high, To turn the fan off rotate the speed switch to marked with (0) off.
The SPEED is adjusted by pressing the speed switch for your desired level.
To start and stop oscillation of the fan head, push down the oscillation knob to oscillate, pull oscillation knob to stop.

CARE AND CLEANING

WARNING: ALWAYS UNPLUG THE UNIT BEFORE MOVING OR SERVICING. DO NOT IMMERSE THE POWER CORD, PLUG OR THE WHOLE UNIT INTO WATER, OR RINSE IT UNDER THE TAP!

CAUTION : Do not use detergent, gasoline, benzene, thinner, or other solvents to clean the unit, to avoid damaging the appliance.

Unplug the unit and wait until the fan stops running before cleaning.
Use a damp cloth to clean the surface of the fan.
We recommend cleaning the fan once a month.
It is not recommended to take the fan apart, except by the authorized agent or any agent qualified to undertake electrical repairs.
If the fan will not be used for a long time, store in a cool, dry and safe place, away from heat and direct sunlight.

FAN STORAGE

Your fan can be stored other partially disassembled or assembled. It is important to keep it in a safe, dry location. If stored disassembled, we recommend using the original (or appropriately sized) box.