UTEN AW558 Shower Caddy Soap Dish Instruction Manual

: September 23, 2024
: Uten

Table of Contents

Product Manual
Read User Manual Online (PDF format)
Download This Manual (PDF format)

UTEN AW558 Shower Caddy Soap Dish Instruction Manual

Models

| UTEN Shower Caddy| AW558
---|---|---
Mode : AW558
Product Size: 30.5×20.7x14cm
Weight ：416g
Material : ABS+TPR
| UTEN 4-in-1 Shower
Caddy Set-Grey| ZH8891
Mode : ZH8891
Product Size : 30.5×20.7x14cm
Weight ：600g
Material : ABS+TPR
| UTEN Shower Caddy-White| AW639
Mode: AW639
Product Size : 30.5×20.9x12cm
Weight : 373g
Material : ABS+TPR
| UTEN Shower Caddy-Grey| AW639
Mode : AW639
Product Size : 30.5×20.9x12cm
Weight : 373g
Material : ABS+TPR
| UTEN 3-in-1 Shower
Caddy Set-White| ZH912
Mode : ZH912
Product Size : 30.5×20.7x14cm
Weight : 582g
Material: ABS+TPR
| UTEN Soap Dish| AW561
Mode : AW561
Product Size : 14.2×11.1×10.3cm
Weight ：128g
Material : ABS+TPR
| UTEN Soap Dish -Grey| AW561
Mode : AW561
Product Size : 14.2×11.1×10.3cm
Weight ：128g
Material : ABS+TPR

Product Manual

Product: OK Suction Mounting Series

Product Features:

Portable and easy installation.
Vacuum suction design, no need for nails or glue.
Leaves no marks or residue on the wall.
Can hold up to 10kg of weight.
Instant installation and ready to use.
Strong suction power and temperature-resistant.
Reusable and detachable soap dish for easy cleaning.
Provides drainage and ventilation.

Suitable for:

Bathroom, kitchen, refrigerator door.
Suitable for various non-porous wall surfaces, including rough ceramic tiles, glass, etc.

Important Reminder:

The surface must not have a height difference greater than 0.5mm.
Not suitable for porous or defective surfaces, including but not limited to unpainted walls, textured walls, latex-painted walls, breathable wallpapers, low-quality or old ceramic tiles, natural marble, and unpainted wooden boards.

Usage and Installation:

Before installation, carefully read and keep this manual.
Use a damp cloth to clean the installation surface, removing any dust or grease (refer to Figure 1 ).Ensure that the suction surface is completely dry before installation.
Gently remove the transparent protective cover from the suction cup. Place the product on the installation surface horizontally, pressing firmly in the direction of the suction surface with one hand while holding the product with the other hand (refer to Figure 2 ). This will expel the air inside the suction cup and create a strong seal.
To remove the product, insert a thin, rigid tool between the suction surface and the suction cup. Rotate the tool slightly to release the suction cup (refer to **Figure 3).

**

Disassembly:

To remove the product, insert a thin, rigid tool between the suction surface and the suction cup. Rotate the tool slightly to release the suction cup.

Maintenance Tips:

If the suction cup gets dirty, clean the surface with water and let it dry before reuse.
Avoid prolonged exposure to direct sunlight. If the suction power decreases after extended use or relocation, soak the suction cup in water at around 80°C for a few minutes, then let it dry. This will restore the suction cup to its original performance.
Avoid installing on tile gaps. If the suction cup does not hold firmly even when installed correctly, it may be due to air leakage caused by the porous or defective installation surface.
We hope this manual helps you with the installation and use of our product. If you have any further questions or need assistance, please contact our customer support.