Joiimu JM3 Retro FM Radio Bluetooth Speaker User Manual

Joiimu JM3 Retro FM Radio Bluetooth Speaker

User manual

• Thank you for purchasing the Retro FM Radio Bluetooth Speaker .
• This speaker has been intelligently designed for very simple operation!
• However, please read this manual carefully before starting to operate the speaker.

Packing Accessories

• JM 3 speaker*1
• Type-C charging cable*1
• AUX cable*1
• User Manual*1

Button schematic

Buttons definition

Appearance outline

1. Speaker driver
2. Status indicator
3. FM knob
4. FM frequency dial
5. AUX input
6. SD card slot
7. Type C charging port
8. Charging indicator

Operation

FM radio mode

1. Short press the “FM” button to switch to “FM” mode, the FM background light is always on.
2. Rotate the FM knob to search for the radio station.
   Note: Some radio stations maybe interfered by the charger while charging the speaker.

Bluetooth connection & play

1. Short press ” M” button, switch the speaker to BT mode. At this time, the status indicator flashes.
2. Open the Bluetooth list of your device and select “IM 3” to connect and pair.
3. Long press the ” M” button to cancel pairing compulsively.

Memory card (SD card)

1. Insert the SD card into the “SD CARD” port on the back of the speaker.
2. Short press ” M” button to switch to SD card mode, the music in the SD card will be played.
3. Long press the Play/Pause button to play the single song in a loop.
   • Long press the Play/Pause button again to cancel the loop.
     Note: The speaker only supports file format FAT32, music format MP3, WAV, WMA, FLAC, APE.

Audio connect and play

1. Use the audio cable to connect mobile phones, tablets, computers, MP3 and other audio source devices to the AUX port of the speaker.
2. Short press ” M” button to switch the speaker to AUX mode, then can play the music.

Charging

1. when the speaker power is insufficient, it will emit a “dong dong” low- battery prompt sound .at this time need to charge the speaker.
2. The red indicator light is always on when charging, the indicator light is off when fully charged.
3. To extend the battery life, if the speaker is not used for a long time, it is recommended to charge every three months.

Specification

• Product:  Retro FM Radio Bluetooth Speaker
• Model: JM 3
• Material: ABS, Walnut log, iron
• Weight: 680g(Excluding cable)
• Size: 1709090MM (WHD)
• Bluetooth version: 5.1
• Bluetooth protocol: A2DP, AVRCP
• Power: 10W
• Distortion: <1%
• Frequency Response: 60Hz-16KHz
• FM frequency: 87.5-108MHz
• Battery capacity: 2200Mah
• Rated input: 5V 1A
• Charging time: 3-4H
• Working time: 10H
• Operating Temp: -10C° -50C°
• Manufacturer: shenzhen ihold technology co.ltd

www.ihold.cc Made in China

Contact

Designated Agent Information:

• Company Name: FCC US Agent, LLC
• FRN: 0033402884
• Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
• Contact Person: Tim Payne
• Phone: 708-571-3148
• Email: Support@FCCUSAgent.com

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject tothe following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency Exposure Statement for IC

This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>