DOD FS588 Dash Cam User Manual

FS588 Dash Cam

“`html

Specifications:

• Model: FS588
• Memory Card: Consumable item, replace as needed
• Recording Time: 00:02:13
• Date Format: 1111//0066//22002223
• WiFi Mode: Available for models with WiFi capability

Product Usage Instructions:

Safety Instructions:

When the machine needs to be idle for a long time, place the
host in a dry environment at room temperature to avoid excessive
battery discharge.

If the host cannot boot up, connect it to a power charger for a
few minutes before turning it on.

Buttons and Screen Display:

Button functions and screen displays vary by model. Refer to the
user manual for specific details.

Installation:

Ensure proper installation location and alignment. Connect the
host and rear lens USB cable before connecting the car charging
power to reduce damage chances.

Connected Power:

The machine will automatically turn on and start recording when
the vehicle is started, and will turn off when the vehicle is
turned off. For models with constant power source, unplug USB power
source after turning off the engine to power off.

Watching Videos:

Videos are stored on a memory card and can be watched in
playback mode on the camera or by inserting the card into a
computer.

Files on the card are categorized as loop recording clip and
locked file folder for emergency recordings.

WiFi Function:

For models with WiFi capability, scan the QR code to download
the DOD Dashcam APP to your smart device.

Frequently Asked Questions (FAQ):

Q: How do I know when to replace the memory card?

A: The memory card is a consumable item and must be replaced
based on usage. It is recommended to replace it when needed.

Q: What should I do if the host cannot boot up?

A: If the host cannot boot up, connect it to a power charger for
a few minutes before attempting to turn it on.

“`

FS588
User Manual

Safety instructions
About the product · For your safety, please do not watch the video or operate the product while
driving. To install and set up this product, please park your car in a safe place first. · Please read this User’s Manual before operating the product. · Do not install the product in a place where it may cause interference with the use of the product. · Do not use the product in high temperature and highly humid environments. · Please do not leave this product in direct sunlight for a long time to avoid reducing the life of the product. When not using the product, please store the product in a dry environment at room temperature. · If the machine breaks down during use, do not disassemble or repair it yourself, but contact your local product dealer.
About car chargers · Please use the charger provided by the original manufacturer. Using a
non-original charger may cause malfunction or danger. · Please do not keep inserting and removing the car charger to avoid damage. · Do not touch the car charger when your hands are wet. · If the car charger is damaged, do not try to repair it yourself, but replace it
immediately.
About Batteries · Some models have built-in batteries, please avoid using them in high
temperature environment. · Because the battery will be automatically discharged even when not in use,
so when the machine needs to be idle for a long time, please put the host in a dry environment at room temperature to avoid excessive battery discharge in a low state resulting in the inability to boot up, such as the occurrence of the host can not boot up, please connect the host to the power charge for a few minutes and then turn on.
1

Other Description
Product Upgrade Please go to the DOD website to download the latest software. When downloading the latest software, please check the system version first (if the host’s current software version is higher than the version released on the official website, it is recommended not to change the software). · Connect the memory card in the host to the computer with a card reader. · Go to the DOD website and search for [corresponding product model] Support Update and Download. After downloading, please extract the update file and copy it to the root directory of your memory card. · After copying, insert the memory card into the host computer, connect the power, the machine will automatically run the upgrade program, and the machine will automatically boot up after the upgrade is completed. · After the product upgrade is completed, please have the host system formatted to avoid repeating the update the next time you boot up.
About Memory Cards · It is recommended to format the memory card about every two weeks to
ensure that the card works properly. · It is recommended to use Class C10 U3 V30 or above, MLC process memory
card (3000~10000 write count). Memory card capacity depends on the model: Memory cards up to 256GB are supported. · Do not remove the memory card directly when the device is turned on. It is recommended that you turn off the device before removing the memory card to avoid damaging the recorded files on the memory card.
NOTE: The memory card is a consumable item and must be replaced by a new one depending on the usage.
2

Buttons and screen display

• Button functions and screen displays vary by model

G F
I H

A. Subnet switching / WiFi B. Microphone / Downward C. Confirmation / Playback D. Upward / Recording E. Power Switch / Menu

A BCDE
F. Rear lens connection port G. Power port H. Memory Card I. Reset key

Recording Time
00:02:13
Date
1111//0066//22002223

LOCK GPS

Time

Resolution Menu Bar

3

WiFi mode

Settings / Playback

Standby / Recording Mode

Mode

Button

Description
Switch on/off
Short press: Lock file Long press: capture in video Short press: Go to playback Press and hold: Switch to record on/off Short press: Go to setting menu Press and hold: Switch on/off recording Short press: switch the front and back lens display screen Long press: Switch WiFi on/off
Switch on/off

Top Menu

Confirmation

Next Menu

Back

Switch on/off

Locking File

SSID SSID display

Snapshot in the video

Short press: switch the front and back lens display screen Long press: Switch WiFi on/off

Lamp Number

Description

Red Light

In the video

Green Light

WiFi mode

LED Lamp No.

4

Installation
Installation location and alignment
Drawings are for reference only, subject to the real thing
Cleaning windshields Installation Find a suitable location on the car, not blocking the driver’s view and safety, install the bracket and hang the machine. Adjust the lens angle Adjust the angle of the lens by adjusting the angle of elevation of the main unit to make sure it is level with the ground. Do not forcefully twist the cable set inside the ball head of the bracket to avoid damage to the bracket. Memory Card Please insert the card into the host according to the card slot icon [ ]. To ensure that the card can be used normally, please format the card with the host first. *Formatting will delete all the data in the card, so please keep the important data first.
5

Connected Power Before connecting the power, please be sure to first connect the host and rear lens USB cable installation is complete, finally connect the car charging power to the car to reduce the host and rear lens damage chance.
NOTE: Please use the original car charger to avoid damage caused by non- compliance with the specifications. If there is oil, fingerprints or other dirt on the inside or outside of the windshield, wipe it clean before installing it. When using the bracket, please choose the position carefully. Do not place the main unit in a position that will obstruct the view of driving or affect the normal operation of the airbag. Road conditions vary from country to country, so it is recommended to set the gravity sensor to “low” to avoid frequent gear locking.
Turn on and off The machine will automatically turn on and start recording when the vehicle is started, and will automatically turn off when the vehicle is turned off and the power is cut.
NOTE: For certain models, the power will not be cut off immediately when the vehicle is turned off. This situation may cause the machine to continue to consume power, which may lead to the depletion of the vehicle battery. Constant Power If your vehicle recorder is connected to a constant power source, simply unplug the USB power source after the engine is turned off to turn it off.
Watch the video The video will be stored on a memory card, which can be watched in playback mode by the camera or by inserting the card into a computer.
The files on the card will be categorized as follows: Loop recording clip: The length of the video varies depending on user settings. Video folder is VIDEO Lock the file folder to EMERGENCY
Example. Previous video file name: 20230601192757_000001A Post-camera video file name: 20230601192757_000001B *The string represents the date and time the video was shot (in the order of year, month, day and 24 hours)
6

WiFi This function is available for models with WiFi capability. Please scan the QR code link to APP store to download the latest version of “DOD Dashcam” APP to your smart device.

Android

iOS

Note: DOD Dashcam APP supports version iOS7 or above Android4.5 or above. As each model varies, it is recommended to update your smart device to the latest version.

7

Link Description 1. Press the Wi-Fi switch on the machine Open AP mode Use your phone
or tablet to connect to the machine Wi-Fi and enter the password After the connection is completed, you can start the operation. Preset password: 12345678
00:02:13 SSID SSID:FS588 PWA2:12345678
2. After opening the APP, click the camera icon to enter the camera list, click the link icon of the model you want to connect, then finish the APP connection.
3. Or follow the image step-by-step instructions in the App Help Guide to link. Note: ·The Wi-Fi password only needs to be entered the first time you connect, and if
it is not changed, you can skip the password entry for the next connection. ·The password can be changed within the app, and is limited to English
semi-formats, with symbols and spaces disabled. ·Wi-Fi connectivity varies depending on the distance and environment, and the recommended range is within one meter.
8

123

4

567 8

1 Switching front and rear camera 6 File Browse

display
2 Capture the moment 3 Turn on/off recording 4 Return to Link Control page

7 Turn on/off recording 8 Settings 9 Google Map
*Need to turn on the phone GPS

function

9

Function Setting Menu

The menu varies depending on the model, so please refer to the update instructions released with the firmware for adding, deleting or changing features.

Press [

] once to enter the function setting.

Function

Options

Resolution
Video format
Screen Display
Loop Recording Date/time WiFi Recording GPS Status Parking Monitoring Crash Sensitivity WDR
Film Marker
Image editing format Rear lens mirroring Exposure settings (before) Exposure settings (after) Key Tone Screen Protection Language
Formatting Memory Cards
Formatting Tips Restore the original factory settings

4KP30 / 1600P30 / 1440P30 / 1296P30
4KP30+1080P30 / 1600P30+1080P30 / 1440P30+1080P30 / 1296P30+1080P30
TS / MP4
Front lens / Back lens / Sub screen
1 minute / 3 minutes / 5 minutes 2022 / 01 /01 / 00:00:00 Open / Close Open / Close Watch GPS Receiving Status Close / 1 second 1 shot Close / Low / Medium / High Open / Close Time / Time + Latitude / Time + Latitude & Longitude hourly speed H.264 / H.265 Open / Close -1.0-2/3-1/3+00+1/3+2/3+1.0 -1.0-2/3-1/3+00+1/3+2/3+1.0 Open / Close Close / 1 minute / 3 minutes Traditional / Simplified Chinese / English All data will be deleted after formatting the card Cancel/Confirm Close / 15 days / 30 days / 60 days Restore appearance settings and menu cancel/confirm

Preset value 1440P30
Single front mirror 4K30+ 1080P30
Double Mirror MP4
Mother and Child Screen
1 minute
Close Open
Close Close Close
Time
H.265 Close
00 00 Open 1 minute
60 days

10

DOD Warranty Terms

DOD LIMITED WARRANTY

Product Category Camera
Battery
Parts & Accessories

Warranty Period

Note

1 years 6 months 6 months

Warranty period is effective on the date of purchase of the product from DOD’s authorized dealers.
Malfunctions and damage caused by misuse, neglect, natural disasters or
abnormal electricity currents will not be covered by the warranty.

1. Please keep the invoice and warranty card. 2. If the invoice or warranty card for the camera is missing, please
provide the device’s serial number to DOD customer service so that the warranty can be fulfilled.

The product is not included inside the warranty 3. Malfunctions and damage caused by misuse, neglect, natural
disasters or abnormal electricity currents will not be covered by the warranty.

All rights reserved by DOD Tech Co.,Ltd
11

Guarantee Certificate

Product

Model No.

Serial No.

Date of Purchase

DOD authorized distributor

Copyright ©2024 DOD Tech Co., Ltd. All Rights Reserved
Under the copyright laws, this manual may not be copied, in any way, shape, or form, without the written consent of DOD Tech Co., Ltd.
12

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>