Cync CWLSWDMBWF1,CWLSWCCBWFI Wire Free Smart Switch Installation Guide

Cync CWLSWDMBWF1, CWLSWCCBWFI Wire-Free Smart Switch

Simple DIV Setup

1. STEP 1 Install your Wire-Free Smart Switch
2. STEP 2 Download the Cync App, powered by Savant, on your smartphone
3. STEP 3 Add your Wire-Free Smart Switch to the Cync App

• For set-up help, visit support.gelighting.com or call 1-8lili-302-29li3
• GE and C by GE are trademarks of General Electric Company. Used under trademark license. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
• Google and other related marks and logos are trademarks of Google LLC

Compatibility Requirements

• Works with Cync and C by GE Smart Lights, Plugs, Switches, and Sensors. Not compatible with non-C by GE and non-Cync smart devices.
• NOTE: Wire-Free Smart Switch and other Cync Smart Lights, Plugs, and Switches must be grouped in the same Room/Group in the Cync App to enable device control.

Let’s Do It

INCLUDED

YOU’LL NEED

OPTIONAL

You Got This!

• And we’re here to help.
• For in-depth instructional videos and a guided tour through the installation, go to support.gelighting.com or call l-8Lili-302-29Li3
• BEFORE YOU DO ANYTHING!

Location & Mounting Type

• Decide how you want to mount your switch.
• This switch can be mounted to the wall in two ways, by screws or adhesive tape.
• Once you determine which install method is best for you, select one of the following setup methods.

Installing Your Smart Switch

Mounting with adhesive tape

IMPORTANT: Start by removing the clear plastic tab from the back of the Smart Switch.

1. STEP 1 Identify where you want to mount your Wire-Free Smart Switch (switches are typically located £,8-52″ from the floor to the top of the switch).
2. STEP 2 Prior to installation, be sure that the surface is smooth and degreased.
3. STEP 3 Apply adhesive tape to the middle back of the Smart Switch. The adhesive tab should stick out from the side of the switch. This will be covered by the wall plate and allow removal if needed in the future.
4. STEP 4 Mount Wire-Free Smart Switch to the wall.
5. STEP 5 Screw on the faceplate bracket, then snap the faceplate cover onto the bracket.

Mounting with screws/single-gang wall plate

IMPORTANT: Start by removing the clear plastic tab from the back of the Smart Switch.

1. STEP 1 Identify where you want to mount your Wire-Free Smart Switch (switches are typically located L,8-52″ from the floor to the top of the switch).
2. STEP 2 Mark the location for the holes to be drilled. We suggest using the mounting holes on the switch housing as a guide. Use the level (optional) to ensure the switch is level before drilling holes.
3. STEP 3 Using a 7/32″ bit, drill holes in the wall for mounting screws. Insert drywall anchors.
4. STEP 4 Secure the Wire-Free Smart Switch to the wall until level and flush.
5. STEP 5 Screw on the faceplate bracket, then snap the faceplate cover onto the bracket.

Mounting with screws/2-gang wall plate

IMPORTANT: Start by removing the clear plastic tab from the back of the Smart Switch.

1. STEP 1 Remove the existing wall plate.
2. STEP 2 Get a multi-gang wall plate (purchased separately).
3. STEP 3 Use a new wall plate to mark the location for holes to be drilled.
4. STEP 4 Using 7/32″ bit, drill holes in wall for mounting screws. Insert drywall anchors.
5. STEP 5 Secure the Wire-Free Smart Switch to the wall until level and flush.
6. STEP 6 Screw on the faceplate cover onto the bracket.

Simple Set-Up Using the CYNC App

Unlock full features and connect to other CYNC devices

1. STEP 1 Download the Cync App, powered by Savant, on your smartphone.
2. STEP 2 Press any button on the Smart Switch to initiate set up. An LED indicator light will flash blue until the opp setup is complete.
3. STEP 3 Add your Wire-Free Smart Switch to the Cync App.
4. STEP 4 Add your Wire-Free Smart Switch and other C by GE or Cync devices that you want to control into the same Room or Group in the Cync App.

What You Can Do With Your Wire-Free Smart Switch

Wire-Free Smart Switch + Smart Bulb

• Control lights without leaving your bed or couch
• Dim and brighten lights from the switch
• Keep switch control entering a room after moving furniture and plugging lamps into different sockets

Wire-Free Smart Switch + Smart Plug

• Control devices like fans and space heaters with the switch
• Add switch control to table and floor lamps with integrated LEDs or non-standard bulbs
• Keep switch control entering a room after moving furniture and plugging lamps into different sockets

Wire-Free Smart Switch + Wired Smart Switch

• Create 3-way connections without rewiring
• Control lights outside a room, like a kitchen light from the hallway
• Set up a master on/off switch next to your bed

Removing/Replacing the Battery

Uses one CR2032 coin battery

1. STEP 1 Remove the Wire-Free Smart Switch from the wall.
2. STEP 2 Remove the rear housing of the switch using a Phillips screwdriver.
3. STEP 3 Slide the battery out, toward the top of the switch.
4. STEP 4 Slide a new battery underneath the contact strap, with the ( •) terminal toward the back of the fetch.
5. STEP 5 Replace rear housing.
6. STEP 6 Secure the Wire-Free Smart Switch back onto the wall.

Additional Information and Warnings

FCC Compliance Statement Compliance Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated under the provided instructions to provide a separation distance of at least 20 cm from all persons.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

CAUTION! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference;
2. This device must accept any interference, including interference that may cause undesired operation of the device.

• The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and complaints.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Additional Information and Warnings

• Electric Ratings 3V
• Operating temperature: O to Li0°C
• Type 1 Enclosure
• Indoor use only
• The Wire-Free Smart Switch uses one CR2032 battery (pre-installed). If installing the Wire-Free Smart Switch to an outlet box, follow the National Electrical Code (NEC) (ANSI/NFPA 70), Canadian Electric Code, Part 1 (CEC), and local codes by a qualified technician.
• WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery.
• If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• The cells shall be disposed of properly, including keeping them away from children, and even used cells may cause injury.
• Like your new Wire-Free Smart Switch?
• Share your experience!
• Leave a review where you purchased the product.
• GE and C by GE are trademarks of General Electric Company. Used under trademark license.
• РК-00101925-5

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>