Cync 93128990 Outdoor Full Color Premium Light Strip Installation Guide

93128990 Outdoor Full Color Premium Light Strip

93128990 Outdoor Full Color Premium Light Strip
Installation Guide

What’s included (Devices each sold separately)

Light Strip Contents

16 ft. Full Color Light Strip

1. 16 ft. Full Color Light Strip
2. Power supply with plug
3. (15) Mounting clips
4. (15) Mounting screws
5.  (1) PCS end cap and glue

32 ft. Full Color Light Strip

1. 32 ft. Full Color Light Strip
2. Power supply with plug
3. (30) Mounting clips
4. (30) Mounting screws
5. (1) PCS end cap and glue

Light Strip Extension Contents

Light Strip Extension

1. 8ft Full Color Light Strip
2. (8) Mounting clips
3. 8. Mounting screws

What You’ll Need

1. Drill with a 1/8” drill bit
2. Screwdriver
3. Tape measure
4. Scissors

Easy setup

Set up your Lights with three easy steps:

STEP 1
Connect to the Sync App, powered by Savant

STEP 2
Trim to the desired length

STEP 3
Prep surface and install

Setup in the CYNC app

STEP 1
Plug in and power on your light strip by pressing the on/off button on the power supply.

STEP 2
Download the Cync App, powered by Savant on your smartphone

STEP 3
Add your smart lights to the Cync App

For set-up help, visit cyncsupport.gelighting.com or call 1-844-302-2943
GE and C by GE are trademarks of General Electric Company. Used under trademark license.
Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
Google and other related marks and logos are trademarks of Google LLC.

Measure & Trim to Size (If desired)

STEP 1
Measure where you’re planning to install your lights. If your space requires Light Strip Extensions, make sure to attach them before trimming your strips.

STEP 2
With your Light Strip unplugged, safely cut where the trim points are indicated.
Make sure the strip is not plugged in at the wall when cutting.
NOTE: Cutting anywhere else will permanently damage the strip.

STEP 3
Using the end cap and adhesive, put a bead of glue around the inside edge of the end cap and insert at the end of the light strip. Hold in place for 30 seconds.

Strip Bending Options

Prep the Surface & Install Your Strip

STEP 1
Locate the starting point to install your light strip. Install the first clip by drilling a 1/8-inch hole and screwing in the provided screw.
The open ends of the clip should follow the desired direction of your strip.

STEP 2
Install mounting clips every 13 inches until you reach the end of your light strip.

STEP 3
Mount the light strip into the clips by snapping the light strip into each clip. To reposition the strip, unsnap the light strip and reinstall the mounting clip in the desired location.
NOTE: The mounting clips/screws will damage the walls.

Extend Strip & Manually Enable Light Shows (If applicable)

STEP 1
Unplug the power supply. Screw on the waterproof connector to attach the extension to the light strip.
NOTE: 16 ft. The outdoor Strip can be extended up to 32 ft. total. 32 ft. The outdoor Strip can be extended up to 64 ft. total.

STEP 2
Unplug/Plug your strip back in to detect its new length. This is important for Light Effects.

ENABLE LIGHT EFFECTS
Cycle through the light show by pressing the Light Effect button .

FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,  which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC RF  Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

IC statement
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d’Industrie.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils  radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit  accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Like your new Outdoor Full Color
Premium Light Strip?
Share your experience!
Leave a review of where you
purchased the product.

PK-00104672-1

References

• . Spend less. Smile more.
• Cync Product Support Help Center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>