Ventev T Bar Mounting Bracket Clip Installation Guide
- September 18, 2024
- ventev
Table of Contents
Ventev T Bar Mounting Bracket Clip
Specifications
- Product Name: Aruba T-Bar Clip
- Compatible with: Aruba access points for 9/16 in. and 15/16 in. flat T-bar grids
- Material: Plastic
- Includes: Two (2) M4 screws
FAQs
Q: What should I do if the mounting holes on the access point are underneath the t-bar channel? A: In such cases, use the provided plastic cylinder as a bite block to properly secure the clip to the access point. Follow steps 5 to 14 for this scenario.
Q: Can the Aruba T-Bar Clip be used with other access point brands? A: The Aruba T-Bar Clip is specifically designed for Aruba access points and may not be compatible with other brands.
MFG Part Numbers & SKUs
Aruba T-Bar Clip
- MFG Part #: ARUBA-TBAR-BKT-1
- SKU: 278472
Aruba T-Bar Clip, 5 Pack
- MFG Part #: ARUBA-TBAR-BKT-5
- SKU: 246331
Aruba T-Bar Clip, 10 Pack
- MFG Part #: ARUBA-TBAR-BKT-10
- SKU: 219030
PRODUCT USING INSTRUCTION
Ventev Aruba T-Bar Clip Instructions The Ventev Aruba T-Bar Bracket is used to attach Aruba access points to 9/16 in. and 15/16 in. flat T-bar grids. As shown in the figure below, the two (2) M4 screws included with the access point are used to attach the Ventev Aruba T-Bar Clip to the access point.
USING STEP
Step 1
- First, remove any factory brackets from the access point prior to Ventev Aruba T-Bar Clip installation. Retain the two (2) M4 screws used to hold the factory bracket in place.
Step 2
- Orient the access point so that the logo is legible and orient the pull tab of the T-bar bracket so it is facing upwards.
Step 3
- Secure the Aruba T-Bar Clip to the Aruba access point using the two (2) M4 screws included with the access point.
Step 4
- Pull the pull tab of the T-bar bracket and install the access point onto the T-bar, ensuring that both sides of the T-bar are properly seated in each channel of the Aruba T-Bar Clip, as pictured below.
- There are certain Aruba access points where the mounting holes on the access point are underneath the t-bar channel (see images below).
Step 5
- For this scenario, we are including a 0.59 in. diameter x 1.5 in. (15 mm diameter x 38 mm) plastic cylinder to act as a bite block to hold the clip open so it can be properly secured to the access point. To install the bite block into the Aruba T-Bar Clip, place the bite block on a flat surface, as pictured below.
Step 6
- Invert the Aruba T-Bar Clip as pictured below
Step 7
- Secure your fingers to the outside of both sides of the clip base and pull the pull tab to open the Aruba T-Bar Clip.
Step 8
- When the clip opens, place the opening of the T-bar clip over the bite block cylinder, ensuring that the bite block is centered.
Step 9
- Once centered, lower the Aruba T-Bar Clip over the bite block until the top of the bite block sits flat against the inside of the clip base
Step 10
- Slowly close the T-bar clip onto the bite block.
Step 11
- Follow steps 1-3 above.
Step 12
- Once the T-bar is installed, secure the access point pull the pull tab, and remove the bite block from the T-bar clip.
Step 13
- Once the clip is installed onto the access point, pull the pull tab of the T-bar bracket and remove the bite block.
CONTACT INFORMATION
- 11126 McCormick Road,
- Hunt Valley, MD 21031
- 800-851-4965
- sales@ventev.com
- ventevinfra.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>