ventev 050323 26400 mAh 2 Site Survey Battery Pack User Manual

Table of Contents

ventev 050323 26400 mAh 2 Site Survey Battery Pack

ventev 050323 26400 mAh 2 Site Survey Battery Pack

Ports:

PoE Output:

USB-A Output:

LED:

USB-C Input:

USB-C Output:

Battery Type:

Battery Capacity:

Recharging Time:

Products Specifications

The VenVolt 2 Power Bank is the perfect accessory for any WISP technician or wireless engineer. Power your devices with USB-A, USB-C, 24V PoE, and PoE++ (802.3bt).
Carry 26400 mAh of power with you up a tower to remotely power your devices.
The VenVolt 2 Power Bank is temperature resistant and also features protection from various factors such as input overvoltage, output overvoltage, short circuit, and incorrect insertion.

Use provided USB-C wall charger and USB-C to USB-C cable to connect VenVolt 2 to
USB-C charger. Be sure to fully charge your VenVolt 2 before your first use. The battery is shipped under 30% due to regulation requirements.USB-A (Out)
Charging typically takes 3-4 hours to fully charge.
Charging device PoE Device:
- To power a PoE device, use your own ethernet cable to connect from VenVolt 2 to your device.
- Move select switch from Off to 4 for PoE++ port.
- Move select switch from Off to 3 for 24V Gigabit PoE port.
- USB-C port is disabled if switch is set to 3 or 4.
Charging laptop or phone with USB-C port:
- To power a USB device use included cable or your own cable.
- Move select switch to Off.
- Battery will automatically detect a device has been connected and charging will begin.
Charging a device via the USB-A port:
- The USB-A port is on when select switch is set to 3 or 4. When the select switch is set to OFF only the USB-C port is active.

Do not expose the product to fire or other high-temperature environments. The recommended usage temperature is between 14-113°F.
Do not expose the product to water.
Stop using if any of the following conditions occur: electrolytic liquid leakage, overheating, color change, or other unusual conditions.
Do not short circuit the positive (+) and negative (-).

Do not expose the VenVolt 2 to direct sunlight for long periods of time or leave it any place with high temperature or high humidity.
Discharge and recharge the VenVolt 2 periodically if you don’t plan to use it for an extended period of time.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B device complies with Canadian ICES-3(B)/NMB-3(B).
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Problem	Possible Causes	Corrective Actions
The VenVolt 2 cannot be fully charged.

|

The remaining power in the VenVolt 2 cannot be read.| The capacity is fully depleted.|

The VenVolt 2 fails to supply power to devices.|

The capacity is very low.
Poor connection between components.
The VenVolt 2 may not charge certain devices.
Check that the VenVolt 2 is turned on.
Make sure selector switch is set to “USB-C” for USB-C port or switch is set to “3” or “4” for USB-A port.

|