FURUNO HUB-102 Network Hub Installation Guide

INSTALLATION GUIDE
HUB-102 Network Hub

HUB-102 Network Hub

WARNING
Do not open the shield cover unless totally familiar with electrical circuits.
Only qualified personnel should work inside the equipment.
Do not install the unit where it may be submerged in water.
Water in the unit can result in fire, electrical shock, or damage to the equipment.
Use only the supplied power cable.
Fire or damage to the equipment can result if a different power cable is used.
Do not disassemble or modify the equipment.
Fire, electrical shock, or serious injury can result.
CAUTION
Observe the following compass safe distances to prevent interference to a magnetic compass:

| standard compass| steering compass
---|---|---
HUB-102| 0.05 m| 0.05 m

FURUNO ELECTRIC Co., LTD.
 https://www.furuno.com/

Specifications

Equipment List

Installation

Mounting considerations
The HUB-102 can be mounted on a desktop or a bulkhead. When choosing a mounting location, keep in mind the following points:

• Locate the unit where it will not be submerged in water.
• Keep the unit out of direct sunlight to prevent build up heat inside the cabinet.
• Cables should point down to prevent any possible water wicking.

Mounting
Fix the unit to the mounting location with four self-tapping screws, referring to the outline drawing in this manual.

Wiring

Interconnection
To connect NavNet equipment, use the optional cables shown below depending on the unit connected. (All cables below are shielded.)

Waterproof equipment
(Waterproof RJ45 to Waterproof RJ45 Cable)| FRU-RZWPWP-002G| 001-653-250-00| 2 m
FRU-RZWPWP-005G| 001-653-260-00| 5 m
FRU-RZWPWP-010G| 001-653-270-00| 10 m
Non-waterproof equipment
(Waterproof RJ45 to Non- Waterproof RJ45 Cable)| FRU-RZWPNWP-002G| 001-646-960-00| 2 m
FRU-RZWPNWP-005G| 001-646-980-00| 5 m
FRU-RZWPNWP-010G| 001-647-000-00| 10 m
Waterproof adapter cable| | WRJ-ADP-05M| 0.5 m
Multiple HUB-102| | HUB-102-JMP| 0.5 m

Power connection
The HUB-102 power supply must be connected to a power source as follows:
The HUB-102 is protected by an internal auto resetting fuse. Red: V+
Black: V-
White: Frame Ground (FG)
Optional cables
Ethernet waterproof to waterproof cables
Ethernet waterproof to non-waterproof cables Example: Typical System

1. DFF3D Multibeam Sonar
2. Radar Antenna
3. HUB102 Network Switch
4. Network Fish Finder
5. Multi Function Display

Example: System connecting two HUB102’s together

1. DFF3D Multibeam Sonar
2. DRS Radar
3. HUB102 Network Switches connected together to provide 8 ports
4. Network Fish Finder
5. Multi Function Displays

Connect up to 4 HUB102’s in a daisy chain To connect 5 HUB102’s, connect per the diagram belo

Turning Power on, LED function

No operation is required by the user. Simply turn on the HUB-102’s DC power source to power it.
LED display
There are LEDs to monitor power and LAN communication on the unit. The LEDs light, blink or go off according to equipment status as shown in the table below. When the equipment is powered on, LEDs light as following.
Power on sequence

• Power LED: ON
• LAN LEDs: Blink once, then go off.

Equipment off
LAN LED (green)| On
Off
Blinking| Connected to terminal
Disconnected from terminal
Data TX or RX

Compatible model / unit

NavNet MFD| TZT10X / TZT13X / TZT16X / TZT22X / TZT24X / TZTBBX
TZT9F / TZT12F / TZT16F / TZT19F / TZT2BB
---|---
FLEX Function Display| SFD-1010 / SFD-1012
Marine Radar| FR-10 / FR-12
MODEL1815
Fish Finder| FCV-38 / FCV-2100 / FCV-1900G / FCV-1900B / FCV-1900

Dimension Drawing

MINIMUM SERVICE CLEARANCE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>