Luminoso Surface LED Cylinder Installation Guide

Surface LED Cylinder

“`html

Product Information

Specifications:

• Product: LED Cylinder Surface
• Installation: Surface Mounted
• Important Note: Risk of fire and electrical
  shock. Must be installed by a qualified electrician.

Product Usage Instructions

Installation Steps:

1. Ensure fixture is installed by a qualified electrician
   following national and local building/electrical codes.

2. Disconnect power at the electrical panel before servicing.

3. Follow wiring instructions for proper connection (Line,
   Neutral, Dim (+), Dim (-), Pink, Violet).

4. Choose the installation method based on whether it’s surface
   mounted in the recessed J-box or surface mounted in the surface
   J-box.

5. Secure the trim and engine together with a clockwise
   direction.

6. Refer to the parts list for components needed during
   installation.

Structure of Lamp:

• Trim: Part 1
• Engine Cover: Part 2
• Cove: Part 3 (available in 4/6/8 sizes)
• Screw: KM4*22 (Part 4)
• Wire Nut: Part 5
• Lamp: Part 6 (available in 4/6/8 sizes)
• Canopy Power Feed: Part 7 (6 sizes)

Parts List:

1. Octagon Junction Box (By Others) – Part 1
2. Power Cord (By Others) – Part 2
3. Cove – Part 3 (4/6/8 sizes)
4. Screw KM4*22 – Part 4
5. Wire Nut – Part 5
6. Lamp – Part 6 (4/6/8 sizes)
7. Canopy Power Feed – Part 7 (6 sizes)

Frequently Asked Questions (FAQ):

Q: Can I install this product myself?

A: It is recommended to have the LED Cylinder Surface fixture
installed by a qualified electrician due to the risk of fire and
electrical shock.

Q: What should I do before servicing the fixture?

A: Disconnect power at the electrical panel before servicing to
ensure safety.

Q: Are the specifications subject to change?

A: Yes, due to continuous product improvements, specifications
and dimensions are subject to change without notice.

“`

LED CYLINDER

SURFACE

LED CYLINDER INSTALLATION INSTRUCTIONS

RISK OF FIRE AND ELECTRICAL SHOCK. FIXTURE MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN ONLY IN ACCORDANCE WITH NATIONAL, LOCAL BUILDING AND ELECTRICAL CODES. DISCONNECT POWER AT ELECTRICAL PANEL BEFORE SERVICING.

IMPORTANT
1. Read all instructions. 2. Install in accordance with national and local electrical code regulations. 3. This product is intended to be installed and serviced by a qualified, licensed electrician. 4. Do not install in wet locations. For dry and damp use only. 5. Turn off electrical power before installing or servicing fixture in any way. 6. To reduce the risk of fire and overheating, make sure all connections are tight. 7. Under no circumstances can the lighting fixture be covered with heat insulation gasket or similar materials.

WIRING
LINE GREEN NEUTRAL DIM (+) VIOLET DIM (-) PINK

LUMINAIRE
LINE-BLACK GROUND-GREEN NEUTRAL-WHITE
VIOLET PINK

INSTALLATION
1 2 3 4 5 6
Surface Mounted In The Recessed J-box

1 2 7 4 3
5 6
Surface Mounted In The Surface J-box

STRUCTURE OF LAMP
Trim
1

3 4″ /6″ /8″ Cove

4 Screw KM4*22

54 Wire Nut

6 4″ /6″ /8″ Lamp

2
Engine
Cover
When trim and engine are separated, attached together, and secure them with clockwise direction.

7 6″ Canopy Power Feed
PARTS
1 4″ Octogon Junction Box (By Others) 2 Power Cord (By Others) 3 4″ /6″ /8″ Cove 4 Screw KM4*22 5 Wire Nut 6 4″ /6″ /8″lamp 7 6″ Canopy Power Feed

! ATTENTION: Install in accordance with national and local building and electrical codes.
All rights reserved. Due to continuous product improvements, specifications and dimensions are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>