ReGen8 Duo 2 Person Hemlock Infrared Sauna User Manual
- September 15, 2024
- ReGen8
Table of Contents
ReGen 8 Duo – 2 Person
Hemlock Infrared Sauna
USER MANUALhttps://www.lifespanfitness.com.au/pages/product-manuals
Product may vary slightly from the item pictured due to model upgrades.
Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
NOTE:
This manual should not be used to guide your purchasing decision. Your
product, and the contents inside its carton, may vary from what is listed in
this manual. This manual may also be subject to updates or changes. Updated
manuals are available through our website at
www.lifespanfitness.com.au
IMPORTANT SAFETY INSTRUCTIONS
For your safety, it is crucial to adhere strictly to the following precautions while using this product:
- Ensure that children use the equipment under the supervision of an adult. Avoid playing with the equipment for safety reasons.
- Do not insert objects such as fingers or sticks into the heating tube plate to prevent potential dangers.
- Never pour water onto the equipment or the heating pipe (board).
- Avoid using or storing flammable gases or liquids, such as hair spray, oil paint, gasoline, etc., in proximity to the equipment to prevent fire hazards.
- Refrain from placing items inside or on top of the sauna.
- Avoid touching the power control panel and any electrical components with wet hands to prevent the risk of electric shock.
- It is strictly prohibited to use the equipment during thunderstorms to prevent electric shock.
- Do not tilt the equipment and refrain from using sharp objects to strike it.
- Shut down the equipment for half an hour after continuous operation for 4 hours.
- Avoid operating the equipment in a prolonged high-temperature environment.
- Exercise caution when using the equipment after consuming alcohol.
- Individuals with hemophilia or a tendency to bleed should avoid using the equipment.
- Consult your doctor before using if you are currently experiencing illness or taking medication.
- Do not use the equipment immediately after intense exercise; wait until your body temperature returns to normal.
- If you experience any discomfort, cease using the equipment immediately.
- Mind your head when entering and exiting the equipment.
- Do not sleep inside the equipment while it is in operation.
- Refrain from using any bath products in the sauna.
- Avoid touching the heating element to prevent burns.
- Keep the seat timber dry to prevent damage.
- Ensure the floor heater remains dry to prevent excessive sweat dripping.
WARNING: Covering the heater or infrared emitter poses a fire risk!
If you have any questions, please contact the supplier.
STRUCTURE OF INFRARED SAUNA
1. Duster cover
2. Speaker
3. Control box
4. Left board
5. Control panel
6. Front board
7. Handle
8. Door glass
9. Hinge| 10. Ventilation
11. Temperature sensor
12. Top board
13. Back board
14. Heater frame
15. Right board
16. Bench
17. Bench front board
18. Bottom board
---|---
*The structure may vary from different models
INSTALLATION PROCESS
* The structure may vary from different models.Due to our continued product improvement, product illustrated on this instruction manual may vary slightly from the actual product.
INSTALLATION PRECAUTIONS
LARGE PLATE ASSEMBLY
Outer buckle installation methodOuter buckle
installation method ELECTRICAL CONNECTION
CONTROL PANEL OPERATION
Control panel operation (A)
-
Temperature display screen
For temperature. -
Working indicator lamp
Indicate that the heater is working. -
Power indicator lamp
Indicates that the power supply is on. -
Power button
Touch this key to turn on or turn off it. -
Temp control
Touch the ‘+’ and ‘-‘ button to increase or decrease the temperature from 30°C to 65°C. If the ‘heat’ light is on, the temperature setting will increase one degree every time the ‘+’ button is pushed. If pressed for three seconds, the setting will increase quickly. Decrease the temperature in the same manner by pressing the ‘-‘ button. After the sauna reaches the desired temperature, the ‘heat’ light turns off. The Fahrenheit and Centigrade display can be switched: press the temperature button “+” and “-” at the meantime, then press the button of “light” to switch. -
Timer display screen
For timer. -
Light button
Touch the key to turn on/off the light. -
Time control
Touch the ‘+’ and ‘-‘ buttons to set the timer from 5 to 60 minutes. If pressed for three seconds, the timer will increase quickly. To extend the sauna session, reset the timer again.
Control panel operation (B)
-
Temperature display screen
For temperature. -
Timer display screen
For timer. -
USB function
Touch this key to start USB function. -
Light button
Touch the key to turn on/off the light.
See the next page for details. -
Power button
Press and hold this button to switch on and off. -
Temp control
After heater is turned on, press TEMP- and TEMP+ to adjust the heater temperature. See the next page for details. -
Time control
Touch the ‘+’ and ‘-‘ buttons to set the timer from 5 to 60 minutes. Stepping is 5, when the countdown is to 5 minutes, it will beep 3 times. -
Audio function
See the next page for details. -
Button lock function
Long press LOCK button for 5S, indicator light is on, it means the button is locked. Long press this button again for 5S to unlock the button, indicator lamp is not light.
Light Button:
While the system is in standby mode, press the “LIGHT” button to either turn
the lamp on or off separately. If the indicator light is on, it means the lamp
is on; if the indicator light is off, it means the lamp is off.
When the high voltage lamp is on, press for 5 seconds (5S), and the time
display will show “2n,” while the temperature display shows “Lx” (where x is
between 1 and 9).
- When it displays “2n,” a short press of the “LIGHT” button changes the LED light color. Pressing it once changes one color.
- Within 8 seconds without pressing the “LIGHT” button, the time display exits “2n,” the temperature display exits “Lx,” and the LED lamp retains its current color status, exiting the light control logic lock key function.
- You can independently turn on or off the LED light and high voltage lamp. While in the “2n” status, press “TIME-” and “TIME+” separately to control the LED light or high voltage lamp.
Temperature Control:
After turning on the heater, use the “TEMP-” and “TEMP+” buttons to adjust the
heater temperature. The temperature range is from 30 to 65°C (75°C), with a
stepping temperature of 1°C. The Fahrenheit degree range is from 90 to 150°F
(167°F), with a stepping temperature of 5°F.
If the temperature is below 30°C or 90°F, it will display “LO.” To switch
between Celsius and Fahrenheit, press “TEMP-” and “LOCK” simultaneously for 5
seconds.
Audio Function:
-
Press the AUDIO button for the first time, and the indicator light will illuminate. Activate Bluetooth on your mobile device while searching and pairing with the sauna. Once matched (within 6 or 8 seconds), music can be played. The temperature display shows “BLU,” and the time display shows “–Db” or delays for 5 seconds before displaying. Use TIME+ or TIME- to adjust the volume (01-30DB). Short presses of TEMP+- adjust the previous and next music. If the sauna is active and there’s no button press after 8 seconds, the display will show the temperature and time.
Remarks: During Bluetooth pairing, it is not possible to switch between Bluetooth, USB, and radio simultaneously. The switch time takes 6 or 7 seconds. To switch immediately, wait for 6 or 7 seconds.
To stabilize and expedite Bluetooth initialization and pairing, within 8 seconds of opening Bluetooth, disable the load turning on or off function. -
Press the AUDIO button for the second time, and the indicator light will illuminate. Activate the USB function, and the temperature display shows “USB.” Press TEMP+ to adjust the previous music and TEMP- to adjust the next one. The time display shows “–Db.” Press TIME+- to adjust the volume, and short presses of TEMP+- adjust the previous and next music. If there’s no button press after 8 seconds, the display shows the temperature and time.
Attention: It takes 3 seconds to read the USB. If not connected to USB, the volume will show 00db. -
Press the button for the third time to activate the radio. A broadcast prompt sound will occur, and the frequency will be displayed in the temperature display. The time display shows “VOL.” Press TIME+- to adjust the volume, and press TEMP to adjust the frequency. If there’s no button press after 8 seconds, the display shows the temperature and time.
Attention: When the radio is on, long-press the AUDIO button to automatically search for the frequency. The frequency range is (87.5MHZ- 108MHZ). To search for the frequency automatically for the first time in a new location, open the radio and then long-press the AUDIO button. -
Press the button for the fourth time to turn off the sound function.
Control panel operation (C)
-
Display screen
For temperature, time, FM. -
Power button
Touch this key to turn on or turn off it. -
Light button
Touch the key to turn on/off the light inside of cabin. -
Music button
Touch this key to adjust bluetooth, MP3 and FM. FM from 85.7-108.0M. -
USB function
Touch this key to start USB function. -
USB function
Press two key for a second will be FM mode. Press key upon the TRACK for last song and key for next one. -
Temp control
Touch the ‘+’ and ‘-‘ button to increase or decrease the temperature. If the ‘heat’ light is on, the temperature setting will increase one degree every time the ‘+’ button is pushed. If pressed for three seconds, the setting will increase quickly. Decrease the temperature in the same manner by pressing the ‘-‘ button. After the sauna reaches the desired temperature, the ‘heat’ light turns off.
The Fahrenheit and Centigrade display can be switched: press the temperature button “+” and “-” at the meantime, then press the button of “light” to switch. -
Time control
Touch the ‘+’ and ‘-‘ buttons to set the timer from 5 to 90 minutes. If pressed for three seconds, the timer will increase quickly. To extend the sauna session, reset the timer again. -
Pause/Play
When music playing in this mode, this key is for pause or play. -
Volume control
Press ‘+’ and ‘-‘ to increase or decrease volume.
Control panel operation (D)
-
Temperature display screen
For temperature. -
Temperature adjust button
Press ” ∧” and “∨” to adjust the temperature setting. -
Temperature Type
Press to change the temperature display between °C/°F. -
Timer display screen
For timer display. -
Time adjust button
Press “∧” and “∨” to adjust the timer setting. -
Light button
Press the key to turn on/off the light. -
Power Indicator
Indicates the status of the sauna’s main power. -
Work Indicator
Indicates the working status of the sauna. -
Heat Indicator
Indicates the status of heating function. -
Power button
Press this key to turn on or turn off the sauna. -
Work Start/Stop
Press to control the working functions of the sauna.
Control panel operation (E)
-
Display screen
For temperature and timer display. -
Temperature button
Press the key to temperature adjustment state. -
Light button
Press the key to turn on/off the light. -
Time button
Press the key to time adjustment state. -
Power button
Press this key to turn on or turn off the sauna. -
Adjust button
Press “∧” and “∨” to adjust the temperature setting and the timer setting. -
Temperture type
Press to change the temperature display between °C/°F. -
Pause/Play
Press to control the working functions of the sauna. -
Bluetooth
Control panel can be connected to devices to play music.
Control box (A)
This control box is the control center of the sauna room; it is installed on the top board with input/output connections as below.
- Fuse reset
- Main power of sauna room
- Heaters power output cable (LOAD A–LOAD D)
- Lamp power output cable
- Heaters power output cable (LOAD E–LOAD F)
- 12V output
Temperature sensor connection port Control panel connecting Color lamp power
output
Control box (B) This control box is the
control center of the sauna room; it is installed on the top board with
input/output connections as below.
- Main power of sauna room
- Lamp power output cable
- Heaters power output cable (LOAD A–LOAD D)
- Fuse reset
- 12V output
Temperature sensor connection port
Control panel connecting
Antenna
USB output
Color lamp power output
Audio output
Control box (C)
This control box is the control center of the sauna room; it is installed on the top board with input/output connections as below.
- Main power of sauna room
- Heaters power output cable(HT1–HT8)
- Reading lamp power output cable
- Color lamp power output cable(optional)
- 12V output
- 24V output
- If necessary can connect another power box
- Temperature sensor connection port
- Control panel connecting
- Fuse reset
Control box (D)
This control box is the control center of the sauna room; it is installed on the top board with input/output connections as below.
1. Main Power | Main Power of the sauna room |
---|---|
2. Heater | Heaters Power output cable( HT1, HT2, HT3, Ht4) |
3. Reading Lamp | Reading Lamp power output cable |
4. Roof Lamp | Roof Lamp power output cable (in some models) |
5. Color Lamp | Color lamp power output cable(optional) |
6. Ctrl | Control panel connecting |
7. CD/Sig | Signal cable group |
8. Adjust | Color adjust |
9. Fuse | Fuse Reset |
The functions of COLOR LAMP and ADJUST are useful only when color lights are set up in the sauna.
MAINTANCE
Before Using:
- Please be sure to follow the instruction manual before operations.
- Prepare a towel on the seat bench to prevent sweat from dripping onto it, to avoid affecting the quality and beauty of the wood.
After Using:
- Please unplug the power plug promptly.
- Open the door to let the heat and humid water vapor dissipate, keeping the sauna cabin dry.
Stain on Wood:
- Wipe the outer cabin with a wrung wet towel.
- Use a small vacuum cleaner to wipe the inner cabin.
- Do not use organic solvents such as gasoline, alcohol, etc., to wipe the sauna surface.
- Avoid using sharp objects in the sauna cabin to prevent scratching the wood.
Stain on Glass:
- Wipe the glass with soft paper.
- Stubborn stains can be wiped with a damp cloth, then dried with a dry cloth.
- Do not scratch the surface with a sharp object to prevent scratching the glass.
Transportation and Storage:
- Avoid water, snow, and intense impact during transportation.
- Do not store it in a humid environment.
- In the northern climate, which is relatively dry, frequently wipe the product with a wrung wet towel.
- In the southern climate, which is relatively humid, ventilate and dry the product frequently.
TROUBLESHOOTING
Number | Problems | Possible reasons | Countermeasure |
---|---|---|---|
1 | Indicator light for powersupply not working | The connector is not connected | |
properly | Check the connector or replace a new one | ||
No power supply input | Check the circuit (especially whether there is power |
supply input)
Indicator light is broken| Replace the circuitry panel
2| Indicator light for function is not working| The heating indicator light is
broken| Replace the relevant control panel
The circuit board or components are broken| Replace the circuit board
The temperature sensor is broken| Check if the connection is loose and replace
it
3| Infrared Heater not heating up| The heater is broken| Replace with a new
one of the same specifications
The wire junction or the heater’s wire is loosen| Check and plug them in
securely
The temperature sensor is broken| Check if junction of the temperature sensor
is loosen and replace it
The circuit board of the relay is not work| Replace the circuit board
4| Odor from the sauna| The circuit‘s problems| There is eyewinker
around, remove it
Heater’s temperature over high, cut off the power supply and replace it.
Parts on the circuit is broken
Troubleshooting (A)
Applicable to Section A Controller
Number
| Problems| Possible reasons|
Countermeasure
---|---|---|---
1| Indicator light for power supply not working| The connector is not
connected properly| Check the connector or replace a new one
No power supply input| Check the circuit (especially whether there is power
supply input)
Indicator light is broken| Replace the circuitry panel
2| Indicator light for function is not working| The heating indicator light is
broken| Replace the relevant control panel
The circuit board or components are broken| Replace the circuit board
The temperature sensor is broken| Check if the connection is loose and replace
it
3| Light is not working| The cable is not well connected| Reconnect
The light source is broken| Replace a new light source
Poor electronic transformer| Replace the electronic transformer
4| The temperature display show “EP”| Temperature sensor problem| Check
temperature sensor interface and replace with new temperature probe
5| The temperature display show “H”| The temperature in the sauna room is too
high| Turn off the power and wait un- til the temperature in the sauna room
drops below 60°C
6| Speaker does not work| The power cable on the top is not connected| Connect
the top power cable
Signal cable is not connected or loose| Check and reconnect
Audio device damage| Replace with a new audio device
Troubleshooting (B)
Applicable to Section B Controller
Number | Problems | Possible reasons | Countermeasure |
---|---|---|---|
1 | Poor display | Digital tube quality problem | Replace the display panel |
Digital tube driver IC is damaged
2| Controller can’t boot| CPU burned out| Replace a new CPU
No power input| Check for power
The controller’s connection is loose| Reconnect the control computer cable
3| Temperature display is not normal| Temperature sensor damaged| Replace
temperature sensor
4| Bluetooth is not paired properly| Check if other devices were paired|
Disconnect the original paired device
Check if the Bluetooth version is compatible. The system supports version 2.0
or 4.0.| Replace the matching version
Bluetooth driver module is bro- ken| Replace the four-in-one module
5| Radio without sound| Radio module is broken| Replace the four-in-one audio
module
Speaker cable is broken or the speaker is broken| Replace the wire or replace
the speaker
Motherboard amplifier is broken| Replace the motherboard
6| System Alarm| The screen displays EO and alarms| Sensor disconnection
The screen displays HH and alarms| Sensor disconnection
The screen displays E1 and alarms| Sensor short circuit
7| Stop heating after heating for awhile| The system has overload, over-
current protector action| First check if there is an open circuit, if no open
circuit, restart current limit protector
Temperature sensor partial overheating| Check why the partial area is
overheated
Troubleshooting (C)
Applicable to Section C Controller
Number | Problems | Possible reasons | Countermeasure |
---|---|---|---|
1 | Light bulb is not working | Light bulb is burned out | Replace the light bulb |
Light bulb wiring is loosen | Replace the lamp holder | ||
Problems with electrical control panel | Repair or replace it | ||
2 | Repair or replace it | Power cord is unplug | Plug back power cord to outlet |
Outlet has no power | Check outlet or circuit breaker | ||
Power supply or circuit panel is broken | Replace the power supply or related |
circuitry board
3| Music Player doesn’t work| Power connector is loose or dam- age| Check
connector or replace it
DC power supply is no power to the music player| Check DC power supply wiring
or replace the power supply
Music player is defective| Replace the music player
4| Replace the music player| The speaker is broken| Replace with a new one of
the same specifications
The speaker wire is loosen| Reconnect the speaker wire
The power indicator light for music player is off| Turn on the switch to start
work
5| The temperature display show “Er1”| NTC open circuit, wire is not well
connected| Check and well connect
6| The temperature display show “Er2”| NTC open circuit| Change Thermostat
7| The temperature display show “Er3”| Under -15°| Can’t be functional under
too low ambient temperature
8| The temperature display show “Er4”| The temperature display show “Er4”|
Change Thermostat
Troubleshooting (D)
1. No Heat Coming From Some Of The Heat Emitters:
Solution 1: Check to make sure all the heat emitter cords are properly
connected, including the cord to the heat emitter underneath the bench (if
applicable). Go to the roof, and also check that the heat emitter cords are
properly connected to the cords on the roof and that those cords are properly
plugged into the power supply.
Solution 2: If some of the heat emitters are working, and others are not,
the non-functioning ones may be damaged. Do not continue to operate. Contact
the manufacturer for replacement parts.
Solution 3 : If the heat emitters are not working, but the control panel
displays the time and temperature, then the temperature sensor may not be
plugged in properly or may be damaged. Turn the control panel off, go to the
roof of the sauna, and locate the red and black wires near the air vent
towards the rear of the sauna. After locating the wires labeled “TEMP SENSOR”
disconnect them. Connect the spare temperature sensor. For testing purposes,
insert the “TEMP SENSOR” (just connected) down the vent on the roof so that it
is inside the sauna. Then go to the control panel and press the power button.
If the heat emitters now generate heat, the “TEMP SENSOR” was the cause of the
problem. You may have to wait about five minutes to confirm if the heat
emitters are generating heat. Remove the original temperature sensor from its
hole and replace it with the spare one.
2. Control Panel Malfunctioning
Solution 1: If the control panel turns on but not off, and the displayed
numbers flash, the issue may be a connection problem. Go up to the roof and
locate the “CTRL” wire harness you connected when the roof was installed onto
the sauna room. Disconnect the “CTRL” wire harness, check the pins to make
sure they are straight and not bent, and firmly reconnect the “CTRL” wire
harness. Attempt to turn the sauna on at the control panel and check to see if
the buttons are now responding. Contact the manufacturer for any additional
troubleshooting.
Solution 2: If the control panel will not turn off, the power/work/heat
lights do not come on, or the temperature and timer buttons do not work, it
means the control panel may have been damaged and will need to be replaced.
Contact the manufacturer for additional troubleshooting.
3. Sauna Shows Signs of No Power:
Solution 1: There could be one of a few problems causing this. First,
check to see if the cord from the power supply is plugged into the wall
outlet. Also, check your main circuit breaker to confirm that it has not
tripped. Check the power supply on the roof of the sauna to make sure there
are no signs of malfunctioning, such as a high temperature, burning odor, or
strange sounds.
Also, check to make sure none of the power cords are damaged. If the power
supply is malfunctioning or power cords are damaged, unplug the sauna
immediately and contact the manufacturer.
Solution 2 : If your sauna is plugged in and you have no power at the
control panel, then the power supply may need to be reset. Go to the roof of
the sauna and locate the power supply. Press the RESET button to reset the
power supply. The RESET button is on the same side of the power supply as all
the heater cord connections. Attempt to turn the sauna on at the control
panel. Contact the manufacturer for any additional troubleshooting.
Solution 3: There could be damage to the temperature sensor. If your
sauna arrived with a spare temperature sensor, turn the control panel off and
go to the roof of the sauna and locate the red and black wire near the air
vent towards the rear of the sauna. After you have located the red and black
wires labeled “TEMP SENSOR,” disconnect them. Connect the spare temperature
sensor. For testing purposes, insert the “TEMP SENSOR” (you just connected)
down the vent on the roof so that it is now inside the sauna. Then go to the
control panel and press the power button.
If the heat emitters now heat, then the temperature sensor was the cause of
the problem. You may have to wait about five minutes to confirm if the heat
emitters are generating heat. Remove the original temperature sensor from its
hole and replace it with the spare one.
Solution 4: Check the wiring harnesses coming from the power supply
located on the roof of the sauna. Make sure the wiring harness labeled “CTRL”
is connected to the power supply at one end and connected to another wiring
harness labeled “CTRL” at the other end. If this wiring harness is not
properly connected, then the sauna will show signs of having no power.
WARRANTY
AUSTRALIAN CONSUMER LAW
Many of our products come with a guarantee or warranty from the manufacturer.
In addition, they come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage.
You are entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Full details of your consumer rights may be found at
www.consumerlaw.gov.au.
Please visit our website to view our full warranty terms and conditions:
http://www.lifespanfitness.com.au/warranty-repairs
WARRANTY AND SUPPORT
Any claim against this warranty must be made through your original place of
purchase.
Proof of purchase is required before a warranty claim may be processed.
If you have purchased this product from the Official Lifespan Fitness website,
please visit https://lifespanfitness.com.au/warranty-form
For support outside of warranty, if you wish to purchase replacement parts or
request a repair or service, please visit https://lifespanfitness.com.au
/warranty-form and fill in our Repair/Service Request Form or Parts Purchase
Form.
Scan this QR code with your device to go to lifespanfitness.com.au/warranty-
form
References
- Product Support Forms – Lifespan Fitness
- Home | Consumer Law
- Lifespan Fitness | Treadmills, Cardio and Strength Equipment
- Warranty & Repairs - Gym Equipment – Lifespan Fitness
- Product Support Forms – Lifespan Fitness
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>