GLADIATOR GALG362DPG Premier Welded Tall Cabinet Instruction Manual

: September 14, 2024
: GLADIATOR

Table of Contents

GLADIATOR GALG362DPG Premier Welded Tall Cabinet
Product Information
Product Usage Instructions
Models
CABINET SAFETY
DIMENSIONS
PARTS SUPPLIED
ASSEMBLY INSTRUCTIONS
- Tools and Parts
WEIGHT CAPACITY
ACCESSORIES
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GLADIATOR GALG362DPG Premier Welded Tall Cabinet

Product Information

Product Specifications:

Model Options:
- GALG362DPG – Hammered Granite / Silver Tread
- GALG362DPR – Hammered Granite / Red Tread
- GALG362DPW – Hammered White / Gray Slate
Modelo Options:
- GALG362DPG – Granito Martillado/Plateado Huella
- GALG362DPR – Granito Martillado/Rojo Huella
- GALG362DPW – Blanco Martillado / Pizarra Gris
Premier Welded 84″ Tall Cabinet

Product Usage Instructions

Cabinet Safety:
Your safety and the safety of others are crucial. Always read and follow all safety messages provided in the manual.

Dimensions:

Dimensions:
24″ (61 cm) wide, 36″ (91.4 cm) deep, 84″ (213.4 cm) tall.

Parts Supplied:

M6 x 16 mm hex bolts: 20
Leveling Legs: 4

Assembly Instructions:

Tools Needed: 10 mm Wrench (Included)
Parts for Cabinet: Corner bracket (4), Front kickplate (1), Side kickplate (2), Hanging Rod (1), Full-width shelves (4), Leveling leg (4), Key (2), M6 x 16 mm hex bolt (20)

Install the Leveling Legs and Corner Brackets:

WARNING:
Use two or more people to move, assemble, or install the cabinet to avoid injuries.

Cabinet Use Requirements:

Intended for use in a garage.
Maximum weight limit: 400 lbs (181 kg) for each shelf, not to exceed 2000 lbs (907 kg) for the cabinet.
Hanging rod not to exceed 50 lbs (23 kg).

FAQ:

Q: What is the maximum weight limit for each shelf?
A: The maximum weight limit for each shelf is 400 lbs (181 kg).
Q: Can the cabinet be used in locations other than a garage?
A: The cabinet is intended for use in a garage.

Models

GALG362DPG – Hammered Granite/Silver Tread
GALG362DPR – Hammered Granite/Red Tread
GALG362DPW – Hammered White/Gray Slate

CABINET SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
- DANGER: You can be killed or seriously injured if you don’t immediately follow instructions.
- WARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed.

DIMENSIONS

Callouts	Dimensions
A	24″ (61 cm)
B	36″ (91.4 cm)
C	84″ (213.4 cm)

PARTS SUPPLIED

Callouts	Description	Quantity
F1	M6 x 16 mm hex bolts	20
F2	Leveling Legs	4

ASSEMBLY INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools Needed:

10 mm Wrench (Included)

Parts for Cabinet:

Corner bracket (4)
Front kickplate (1)
Side kickplate (2)
Hanging Rod (1)
Full-width shelves (4)
Leveling leg (4)
Key (2)
M6 x 16 mm hex bolt (20)

Cabinet Use Requirements

Intended for use in a garage.
The maximum weight limit is 400 lbs (181 kg) for each shelf, not to exceed 2000 lbs (907 kg) for the cabinet.
Hanging rod not to exceed 50 lbs (23 kg).

Unpack the Cabinet

Remove the keys from the cabinet.
Open the cabinet door.
Remove and verify the contents. See “Parts for Cabinet” for your model.
Dispose of or recycle all packaging materials.

NOTE:
Keep the outer carton layer. It is needed to cushion the cabinet during leveling leg and corner bracket assembly.

Install the Leveling Legs and Corner Brackets

WARNING

Excessive Weight Hazard

Use two or more people to move, assemble, or install a cabinet.
Failure to do so can result in back or other injury.

Install the leveling legs and corner brackets

A. Front of cabinet
C. Corner bracket
F1. Hex bolt
F2. Leveling leg

Close and lock the cabinet doors.
Using two or more people, place the cabinet on its back using the outer carton layer to cushion the cabinet.
Insert 4 hex bolts (F1) through each corner bracket and into the cabinet. Do not tighten the hex bolts completely if adding the optional kickplates.
NOTE: If adding the optional kickplates, do not completely tighten the hex bolts until all 3 kickplates are in place.
Install the leveling legs (F2) to the corner brackets.

NOTE:
If you need to open the cabinet doors during the installation of leveling legs and corner bracket assembly, open them slowly and do not put any weight on the open doors. This avoids damage to the hinges.

Install the Kickplates (Optional)

NOTE: Kickplate installation is optional on the 84″ Tall Cabinet.

Install the kickplates

A. Front of cabinet
B. Front kickplate
C. Side kickplate
F1. Hex bolt

Position the front & side kickplates to the corner brackets and align kickplate end holes with the holes in corner brackets.
Insert the four hex bolts (F1) through kickplate end holes into corner brackets.
NOTE: The side kickplates will be on top of the front kickplate flanges.
Completely tighten all corner bracket hex bolts.
Return the cabinet to its upright position. Unlock door.

Install the Hanging Rod

The cabinet has pre-installed closet rails on the side panels which are suitable for a hanging rod.

Unlock and open the cabinet doors.
Place the hanging rod into the closet rail openings and slide down and into position.

Adjust Shelves

Remove/Replace/Adjust the shelves

Remove the shelf clips from their shipping position on the sides of the cabinet. Working from the inside of the cabinet and using a blunt tool, push out the white plastic shelf clips.
Discard the clips.
Lift up on the underside of the shelf until the shelf tabs are free of the cabinet slots.
Tilt the shelf up to reposition it within the cabinet or to remove it from the cabinet.
NOTE: Plan your shelf heights and install shelves starting from the bottom. The shelves are supported by the metal tabs on the side walls of the cabinet.
Determine the placement of the shelves.
Tilt the shelf so that one end is higher than the other.
Insert the shelf into the cabinet so that the higher end is directly above the desired slots and push the shelf down in place behind the side slots.
Raise the lower end so it is directly above the desired slots and push the shelf down.
NOTE: A shelf must be located in the center position for the cabinet lock to function correctly. Make sure the shelf tabs are in place behind all the slots, as shown.
Repeat this process for the remaining shelves.

Level the Cabinet

Place the cabinet in the desired location.
Level the cabinet by adjusting the leveling legs.

Adjust Doors
The cabinets are designed with adjustable doors.

Check to see whether the doors need adjusting. It is more often the left door that will need to be aligned.
Using a Phillips screwdriver, loosen all screws attaching the hinge to the cabinet.
Adjust door to the desired height.
Tighten the screws.

WEIGHT CAPACITY

ACCESSORIES

To order accessories, call 1-866-342-4089 and ask for the accessory part number listed below or contact your authorized Gladiator® brand dealer. In Canada, call 1-800-807-6777.
Mounting Bracket Kit – Allows the cabinet to be mounted on Gladiator® GearWall® panels or GearTrack® channels.
Order Part # GABK301PRS