AVAPOW A07 Multi-Function Car Jump Starter User Manual

AVAPOW A07 Multi-Function Car Jump Starter User Manual

Friendly Tips:

Please read carefully the instruction manual so that you can be familiar with the product more conveniently and quickly!Please use product correctly based on the instruction manual.
Perhaps there is small difference between the picture and the actual product,so please turn to the actual product for detail information.

What’s in the box

• AVAPOW jump starter x1
• Intelligent battery clamps with starter cable x1
• High quality type-C charging cable x1
• User-friendly manual x1

Specifications

Product diagrams

Accessories

Charge the Jump Starter batter LED Display

Charging with an AC adapter (Note:AC adapter is not included).

1. Connect the battery input with Type-C cable.
2. Connect the Type-C cable to AC adapter.
3. Plug the AC adapter into a power source.

LED Display
Charging with an AC adapter (Note:AC adapter

How to Jump Start Your Vehicle

This unit is designed for jump starting 12V car batteries only and rated for gasoline engines up to 7 liters and diesel engines up to 4 liters.Do not attempt to jump start vehicles with a higher battery rating, or different voltage.If the vehicle isn’t started immediately, please wait for 1 minute to allow device to cool down. Do not try to restart the vehicle after three consecutive attempts as this may damage the unit. Check your vehicle for other possible reasons why it can’t be restarted.

Operating instructions

First step:

Press the power button to turn on it,check the battery shown on the LED display,then plug jumper cable into battery pack outlet.

Second step:| Third step: Turn on the car engine to start car.| Fourth step:
---|---|---
Connect the jumper clamp to car battery,red clamp to positive,black clamp to negative pole of car battery.| Pull the plug of battery terminal from jump starter and remove clamps from auto battery.

Jumper Clamp Indicator Instruction

Jumper Clamp Indicator Instruction

Item| Technical parameters| Instruction
Input low voltage protection| ****

13.0V±0.3V

| The red light is always on, the green light is off, and the buzzer does not sound.
Input high voltage protection| ****

18.0V±0.5V

| The red light is always on, the green light is off, and the buzzer does not sound.

Work instruction

| ****

Support

| When working normally,the green light is always on, the red light is off, and the buzzer beeps once.

Reverse connection protection

| ****

Support

| The red/black clip of the wire clip is reversely connected to the car battery (battery voltage ≥0.8V), the red light is always on, the green light is off, and the buzzer sounds at short intervals.

Short circuit protection

| ****

Support

| ****

When the red and black clips are

short-circuited, no sparks, no damage, the red light is always on, the green light is off, the buzzer 1 long and 2 short beeps.

Start timeout protection

| ****

90S±10%

| ****

The red light is always on, the green light is always on, and the buzzer does not sound.

Connect to the high voltage alarm

| ****

Support

| The clip is mistakenly connected to battery that is >16V, the red light is always on, the green light is off, and the buzzer sounds slowly and shortly.

Automatic anti-virtual electricity function

| ****

Support

| When the car battery voltage is higher than the Starter battery voltage, the output is automatically turned off and the green light is on,at this time, it can be ignited normally. If the car battery voltage drops and is lower than the starter battery voltage during the ignition process, the smart clip will automatically turn on the output to complete the startup process.

LED flashlight

Short press the Light Button to turn on the flashlight.The battery capacity indicator lights up.Short press the light button again to scroll through the lighting,Strobe,SOS.Short press again to turn off the flashlight.The flashlight offers more than 35 hours of continuous use when fully charged.

Safety Warning

1. Never short circuit the jump starter by connecting the Red and Black clamps.
2.  Do not disassemble the jump starter.If you find swelling,leakage or odor,please stop using the jump starter immediately.\
3. Please use this starter at normal temperature and keep away from humid,hot and fire places.
4. Do not start the vehicle continuously.There should be at least 30 seconds to 1 minute between two starts.
5. When the battery power is less than 10%,do not use the jump starter otherwise the device will be damaged.
6. Before first use please charge it for 3 hours or more.4
7. If the positive clamp of the starting power was incorrectly connected to the negative poles of the car battery,the product comes with relevant protective measures to avoid personal injury and property damage.

Note:

– For the first use, please make sure to fully charge before use.
– In normal use, please confirm that the unit has at least 50% power before use.

Warranty Exemption

1. The product has been incorrectly operated or damaged due to the following irresistible reasons (such as flood,fire,earthquake, lightning,etc).
2. The product has been repaired,disassembled or modified by non-manufacturer or non-manufacturer authorized technicians.
3. The problem caused by wrong charger does not match the product.
4. Beyond the product warranty period(24-month).

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>