RED COMPACT EVF Pack Owner’s Manual

: September 12, 2024
: RED

Table of Contents

RED COMPACT EVF Pack
Specifications
FAQs
CLEANING THE EVF SCREEN
PROHIBITED EVF SCREEN CLEANERS
RED EVF MOUNT WING NUT INSTALLATION GUIDE
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RED COMPACT EVF Pack

Specifications

Product Name: DENZ Premium Optics for RED Compact EVF
Compatibility: DSMC2 RED EVF, RED COMPACT EVE
Material: Optical-grade components
Package Includes: Denz Optics assembly, Wing nuts

FAQs

Was this article helpful?

0 out of 0 found this helpful

Have more questions?

Submit a request

Comments

0 comments

Article Status

Closed for comments

ATTACHING THE DENZ PREMIUM OPTICS TO THE REDCOMPACT EVF

Product Management
March 11, 2024 19:33
FOLLOW

To attach the DENZ Premium Optics to the DSMC2 RED EVF or RED COMPACT EVE, follow thesteps below:

Remove the optics.
- To remove the optics, hold the optics block with one hand so it does not fall when released; with the other hand, move the locking wheel counter-clockwise until you feel a hard stop.
- Slowly move the optics away from the EVF until it is clear of the internal cavity. Store the optics in a dust and moisture free environment. If you need to clean the OLED screen before attaching the new optics, a guide can be found below.
Attaching the new optics.
- To attach the new optics, observe the alignment pin on the EVF optical block and alignment notch on the Denz Optics; both will need to be aligned to securely mount.
- Carefully install the Denz Optics assembly onto the EVF, ensuring both the alignment pin and alignment notch mate correctly.
- Once secured, rotate the locking wheel clockwise until it stops.
Ensure the new optics are secure.
- Before letting go of the new optics, ensure it does not come loose or wobble.

CLEANING THE EVF SCREEN

NOTE : This section describes only how to clean the screen on the DSMC2® RED EVF and RED COMPACT EVF, and not how to clean the entire device.

The screen is accessed by removing the DSMC2 RED EVF/ RED COMPACT EVF Modular Optical Block. Use an ionized rubber air bulb to clean the screen on the EVF. If there are still particles on the screen after using an air bulb, gently wipe the screen with a rolled-up, particulate-free, non-abrasive optical-grade wipe.

NOTE : Cleaning the screen without first removing solid particles increases the risk of scratching the screen. As with many screens, any type of physical contact with the screen may scratch the surface.

PROHIBITED EVF SCREEN CLEANERS

DO NOT use any of the items listed below to clean the screen on the DSMC2 RED EVF. These products have not been tested on RED products and may cause damage or streaking.

Compressed air
Gas dusters
Solvents
Rubbing alcohol
Isopropyl alcohol
Windex®
Third-party cleaning kits
Pre-packaged lens cleaner containing any additives, such as detergent, anti-static compounds, or fragrance
RED Microfiber Bag

RED EVF MOUNT WING NUT INSTALLATION GUIDE

To attach the RED Compact EVF with Denz Premium Optics to the RED EVF Mount or RED EVF Extension Arm, you must replace the thumb screws with wing nuts; these are included with the Denz Premium Optics for RED Compact EVF. To install, follow the steps below:

Remove the thumb screw
- Remove the thumb screw located by the EVF attachment wheel, as indicated below.
Attaching the wingnut
- Attach the included shim over the screw threads and screw in the wing nut into the exposed hole. (NOTE: The wing nut may collide with the locking wheel. Use the ratcheting system of the wing nut to continue to screw in the wing nut or use the included Allen Key tool to tighten

Was this article helpful?

Have more questions? Submit a request

Articles in this section