VisionTek VS627 Smart Projector User Manual
- September 10, 2024
- VisionTek
Table of Contents
VisionTek VS627 Smart Projector
This User Manual is important to you. Please read it before using your projector.
PACKING LIST
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: DO NOT LOOK DIRECTLY THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.
NOTICE:
FUNCTION OVERVIEW
REMOTE CONTROL
- Power : Power on/off the projector Source: Select input signal
- OK : Confirm the setting or enter sub-menu 4 7 4 / Select desired menu times and make adjustments
- Homepage : Jump to the homepage directly
- Exit : Exit and save menu setting
- Menu : Enter menu or go back to previous item
- VOL : Adjust the volume
- Focus +/-: Adjust the focus when the image is
- blurrySettings : Go to the system settings.
Quick Start
PROJECTOR CONNECTION
INPUT SOURCE
Press on the projector or S on the remote to enter the interface of Input Source. Select signal input by using Direction key. Press OK to confirm. Insert USB disk or corresponding signal input cable.
A. Multimedia Connection
Specifications
| Feature | Details |
|---|---|
| Display Technology | LCD |
| Light Source | LED |
| Installation Type | Front table, Front ceiling, Rear table, Rear ceiling |
| Vertical Correction | -50 to 50 |
| Horizontal Correction | -50 to 50 |
| Focus | Manual |
| Keystone Correction | Electronic |
| Speaker | 5W / 4 ohm |
| Power Supply | AC 110-240V, 50/60Hz |
| Dimensions (L x W x H) | 290 x 255 x 110 mm (11.4 x 10 x 4.3 in) |
| Net Weight | 2.8 kg (6.17 lb) |
| Supported Photo Formats | BMP, JPG, PNG, JPEG |
| Supported Audio Formats | AAC, MAV, OGG, MP2, M4A, FLAC, AMR, MPGA |
| Supported Video Formats | AVI, MP4, MKV, MOV, MPG, VOB, MPEG2, H.264, |
MPEG1, TS, TP, DIVX5
Ports| HDMI in x2, USB 2.0 x2, AV in x1, Audio out x1
SETTINGS
Press key on remote or move cursor to settings and press OK to enter.
Projection settings: Change the projection mode according projector installation way. Zoom in/out the images in the range of 50% to 100%.
Correct the images in horizontal/vertical direction or from four corners.
Network settings: Projector searches connectable network automatically when Wifi is turned on. Select desired Wifi. Input correct password to connect. The same Wifi will be connected spontaneously when power on the projector next time if keep Wifi switch on as projector shutdown.
Bluetooth settings: Projector searches connectable Bluetooth automatically when BT switch turned on. Select desired device to connect by pressing OK button. pressing OK. The same BT device will be connected spontaneously when power on the projector next time if keep BT switch on as projector shutdown.
PROJECTION DISTANCE & SIZE
The recommended projection screen is around 80 inches with a projection distance of around 9.58ft. Ambient darkness will improve the clarity of the projected images.
TROUBLESHOOTING GUIDE
-
Blurry Image
Adjust focus ring/keystone.
Project and screen/wall must be in effective distance. -
Remote Unresponsive
Make sure remote points at IR receiver directly.
Do not cover IR receiver.
Try a new pair of AAA batteries. -
Mobile Connection
iOS : Genuine lightning to HDMI cable.
Android : Micro USBto HDMI adapter/Type C to HDMI cable. -
Up Side Down Images
Enter “Image flip” on remote to flip the projector image.
FCC STATEMENT
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>