SILHOUETTE SPRWC052D3SS-P Under Counter Wine Refrigeration Installation Guide
- September 9, 2024
- Silhouette
Table of Contents
SPRWC052D3SS-P Under Counter Wine Refrigeration
“`html
Specifications
- Product Name: PRO GEN 3
- Model: Panel-Ready
- Manufacturer: Silhouette Appliances
- Website: silhouetteappliances.com
- Year: 2024
Product Usage Instructions
Preparation
-
Cut the panel to dimensions shown, including slots for hinge
clearance. -
If applying stain or finish, follow product instructions and
finish both sides to prevent warping. -
Install desired handle ensuring screws sit flush with the back
face of the panel.
Installation Instructions
-
Fully open the door.
-
Pull the gasket away from the door starting at the corner.
-
Continue to pull the gasket free from the gasket channel.
-
Lay the gasket on a flat surface upon removal.
-
Secure integrated panel to the door using clamps or robust
tape. -
Drill pilot holes into the wood panel using a 7/64 (3mm) drill
bit. -
Insert ST4x 25mm screws into the pilot holes and screw down
without over-tightening. -
Ensure screws sit flush against the bottom of the channel.
-
If adjustments are needed, slightly loosen screws, adjust
panel, and tighten screws upon completion. -
Re-install the gasket into the gasket channel in the frame,
starting at the corners and ensuring it is fully seated.
FAQ
Q: What should I do if the panel requires additional adjustment
after installation?
A: If adjustments are needed, slightly loosen
each screw, adjust the panel as necessary, and tighten screws upon
completion.
“`
PRO GEN 3
Panel Installation Guide
The Gen 3 Panel-Ready models make it easy to install custom cabinetry framing
to seamlessly match surrounding cabinetry.
Base Models: · SRBC052D3SS-P · SRWC052D3SS-P · SRWBC052D3SS-P
Please Note · Max. panel thickness 3/4″ (19mm) · Max. weight of panel 20 Lbs
(10 Kg) · Cabinetry frame `panel’ and handle
to be supplied by customer
Suggested Equipment · Drill and 7/64″ (3mm) Drill Bit · Bar Clamps/Tape ·
Phillips Head Screwdriver
Preparation 1. Cut the panel to dimensions
shown, including the slots for hinge clearance. 2. If applying stain or
finish, follow instructions on the product and consider finishing both sides
to prevent warping. In some frame installations, the panel may be visible
through the glass while the door is open. 3. Install desired handle, ensuring
screws sit flush with the back face of the panel.
silhouetteappliances.com | 2024
PRO GEN 3
Panel Installation Guide
Installation Instructions
1. Fully open door. 2. Starting at the corner, pull the gasket away from the
door. See Fig A. 3. Continue to pull the gasket free from the gasket channel.
4. Upon removal, lay the gasket down on a flat surface. 5. Secure integrated
panel to door using clamps. It is
recommended to use bar clamps to secure the panel to the door. A robust tape
may also be used. If using tape, ensure the tape will not damage the panel
finish upon removal. See Fig B. 6. Using a 7/64″ (3mm) drill bit, drill 6
pilot holes into the wood panel 1/2″ (12mm) deep using the holes in the door
frame as a guide.
Notice: It is important to ensure that all drill holes are drilled to the
correct depth in order to avoid splits in the wood when hardwood is installed.
7. Locate 6 of the ST4x 25mm screws provided with your unit.
8. Using a Phillips screwdriver, place one screw into each of the 6 pilot
holes and screw down. Do not over tighten the screws. See Fig C.
9. Ensure the screws sit flush against the bottom of the channel. Remove
clamps from the door.
Notice: If panel requires additional adjustment after removing clamps,
slightly loosen each screw and adjust panel as necessary. Tighten screws upon
completion.
10. Starting at the corners, re-install the gasket into the gasket channel in
the frame. Make sure the gasket is fully seated.
silhouetteappliances.com | 2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>