Wsdcam WT28 Bicycle Taillights User Manual
- September 6, 2024
- Wsdcam
Table of Contents
Wsdcam WT28 Bicycle Taillights
Product Specifications
- Compliance: Part 15 of FCC Rules
- Interference Conditions: Must not cause harmful interference, must accept any received interference
- Radiation Exposure: Complies with FCC limits for an uncontrolled environment
- Minimum Distance: 20cm between radiator and body
Product Usage Instructions
- Ensure that the device is operated in compliance with Part 15 of the FCC Rules to avoid interference issues.
- Do not make changes or modifications to the device that are not approved by the responsible party to prevent interference. Accept all received interference without causing undesired operation.
- For your safety, maintain a minimum distance of 20cm between the radiator of the equipment and your body during installation and operation.
FAQ
- Q: What should I do if I encounter interference issues?
- A: If you experience interference problems, ensure that the device is not causing harmful interference. Check for any unauthorized modifications and revert them if found.
- Q: How can I ensure radiation safety when using the equipment?
- A: To maintain radiation safety, always keep a minimum distance of 20cm between the radiator of the device and your body as recommended in the user manual.
Packing List
Parameters
Charging Tips
- Open the USB waterproof plug of the lamp and insert the charging cable into the Type-C port;
- Connect the cable USB side to the charging adapter.
- During charging, tail light display charging pattern, the tail light displays the charging pattern, and after fully charged, the tail light turns off;
- Power-off: click the power button, and the tail light will display the remaining power in a battery icon.
- Unplug the charging cable and cover the USB waterproof plug when charging is finished.
Notice
- Make sure the charging cable is ok before charging.
- Unplug the charging port and ensure that the USB waterproof plug is covered 100%.
- Do not use sharp objects to press the button.
- Do not turn on the light to the eyes.
- Children can not use it without adults.
- Keep away from fire and high-temperature objects.
How to install
Install under-seat cushion
- Fix two sides of the seat cushion bracket under the seat cushion with a tie.
- Put the tail light into the seat cushion bracket and rotate 90°.
- Installation Finished
Install to the seat tube
- Fix the seat tube bracket to the tube with tie.
- Put the tail light into the seat tube bracket and rotate 90°.
- Installation Finished
Instruction
Turn on/off
- Long press the power button for 0.5 seconds.
Switch pattern
- After powering on, click the power button to switch patterns.
Team Mode
- After powering on, double-click the power button to enter the team mode selection, after entering the team mode selection, click the power button to switch to the required mode TX (captain mode), RX (teammates mode), OFF (independent mode).
- TX (captain mode): In this mode, the tail light pattern of the teammates can be controlled to be consistent with the captain light, and the control distance is about 30 meters.
- RX (teammates mode): In this mode, the tail light pattern is consistent with the tail light pattern in captain mode.
- Note: To prevent two captain mode main lights from appearing in the same place at the same time, confusing the display pattern of the teammates; in teammates mode, only follow the first captain who has completed the pairing with it.
- After exiting the teammate’s mode and re-entering, you can reselect the captain.
- OFF (Independent Mode): In this mode, the tail light operates independently and is not affected by outside influence.
APP Download
- To use this product more comprehensively, please scan the QR code with your mobile phone and download the SageLink APP, or search for the SageLink APP in the application market and download it.
- You can upgrade the device’s firmware, design graphics, set modes, etc. in the APP.
Bluetooth connection
- Turn on the tail light, turn on the Bluetooth of your phone, enter the main interface of the APP, click Bluetooth connection and select the SageLink device, then click OK.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used per the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
Suppose this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. In
that case, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.