Juniper Series II Monitor Arm Installation Guide

: September 5, 2024
: JUNIPer

Table of Contents

Series II Monitor Arm
Specifications
Product Usage Instructions
1. Assembly Options
2. Lock-Out Function Option
3. Attaching Upper Arms and Monitor Plates
4. Removing and Attaching Monitor Plate
5. Locking Monitor Plate for Theft Prevention
6. Cable Management
7. Arm Tension Adjustment
- FAQ
Q: What should I do if my monitor size exceeds 26 inches or
Q: How do I install additional laptop trays?

Series II Monitor Arm

“`html

Specifications

Monitor Arm Model: NXMA Series II
Load Capacity: Varies based on monitor size and depth
Parts Included: Monitor Plate, Upper Arm, Lower Arm, Clamp,
Adhesive Pad, Set Screw, Machine Screw, Flat Head Machine Screw,
Allen Keys (2mm, 4mm, 5mm), Carriage Bolt, Grommet Bar, Hex Nut,
Flat Washer, Wrench

Product Usage Instructions

1. Assembly Options

To assemble the monitor arm, choose between the clamp assembly
option or the grommet assembly option. Follow the specific steps
provided for each option.

2. Lock-Out Function Option

Decide whether to enable the lock-out function. Follow the
necessary steps to set up this feature.

3. Attaching Upper Arms and Monitor Plates

Secure the upper arms and monitor plates using the provided
screws and Allen key (2mm). Ensure the components are properly
fastened but not overly tightened.

4. Removing and Attaching Monitor Plate

To remove the monitor plate from the arm, release the lock
mechanism and detach it. When attaching the monitor plate to the
monitor, align the holes and secure it with screws before sliding
it onto the arm.

5. Locking Monitor Plate for Theft Prevention

Prevent theft by locking the monitor plate with the provided
mechanism. Use a screwdriver to tighten the screw securely in
place.

6. Cable Management

For cable management, detach the arm covers to feed wires
through. Snap wires onto arm clips and reattach the covers once all
wires are neatly fed through.

7. Arm Tension Adjustment

Adjust the tension in both the arm neck and elbow according to
the weight of your monitor. Use the appropriate Allen keys provided
to adjust the tension clockwise for heavier monitors and
counterclockwise for lighter monitors.

FAQ

Q: What should I do if my monitor size exceeds 26 inches or

depth is greater than 5.5cm?

A: If your monitor size exceeds these limits, the loading
capacity might be reduced. Ensure your monitor’s center of gravity
remains within 3cm from the end of the monitor plate interface for
optimal performance.

Q: How do I install additional laptop trays?

A: For each additional laptop tray, you will require another set
of parts listed in the Laptop Tray section. Follow the installation
instructions provided for proper setup.

“`

NXMA
Series II
Monitor Arm
Includes Add-Ons: A1 General Installation Guide

TABLE OF CONTENTS

Edition Code
NXMA :: Monitor Arm…………………………………………………………………… 1
Add-ons
A1 :: Laptop Tray……………………………………………………………………………………. 11

Monitor Arm Overview
Series II Product loading capacities are based on monitor’s
center of gravity less than 3cm from the end of the monitor plate interface. Loading capacity could be reduced if monitor size is greater than 26″ or depth is greater than 5.5cm.
1

MONITOR ARM

Parts List

Code

Qty.

Description

2

Monitor Plate

2

Upper Arm

2

Lower Arm

1

Clamp

NXMA

1

Adhesive Pad

8

Set Screw

2

Machine Screw

2

Flat Head Machine Screw

1

Allen Key (2mm)

1

Allen Key (4mm)

1

Allen Key (5mm)

1

Carriage Bolt

1

Grommet Bar

2

Hex Nut

1

Flat Washer

1

Wrench

2

MONITOR ARM

1A | Clamp Assembly Option
(a) Smaller Desk Thickness: Use Upper Attachment Positioning Adhere pad to clamp base, then clamp to desk edge. NOTE: (#)=clamp opening for desk thicknesses between 1/2″ 1 3/16″

”

(b) Larger Desk Thickness: Use Lower Attachment Positioning Adhere pad to base and remove clamp. Reposition clamp to lower tiered holes at bottom of clamp. Fasten clamp back to base using Allen key (4mm) and clamp to desk edge. NOTE: (#)=clamp opening for desk thicknesses between 1 1/8″ 2 9/16″

”

3

MONITOR ARM

1B | Grommet Assembly Option
Skip to step 2 if using clamp assembly option. Use Allen key (4mm) to loosen three base cover screws, then detach clamp mount and base cover.
Insert carriage bolt between base covers and clamp shut. Remove backing from adhesive and adhere to bottom of base. Insert bolt from base into grommet and secure with hardware.
4

MONITOR ARM

2 | Choose Lock-Out Function Option:
(a) 180°–Select option if installing with dividers or against a wall Insert both lower arms into main base. Fully tighten screws to arms with Allen key (2mm), then back out one full turn.
(b) 360°–Select option for full rotation capability Insert both lower arms into main base. Turn arms to opposite side of base, and fully tighten the screws to base with Allen key (2mm), then back out one full turn.
5

MONITOR ARM

3 | Attach Upper Arms and Monitor Plates
Fasten screws with Allen key (2mm), then back out one full turn.
4 | Remove Monitor Plate From Arm
Remove monitor plate by turning plastic tab to release lock, then pull plate upward to separate from arm.
6

MONITOR ARM

5 | Attach Monitor Plate to Monitor
Place monitor face down on a flat surface. Align monitor plate holes with holes on back of monitor and attach using screws provided. Then slide monitor with attached monitor plate onto arm securely.
6 | Locking Monitor Plate for Theft Prevention
Lock monitor plate by turning plastic tab counter clockwise. Then, use a screwdriver to tighten screw in place.
7

MONITOR ARM

7 | Cable Management
Detach arm covers from bottom of arms to feed through wires. Snap wires on arm clips and then clip back covers when wires have been fed through.
8 | Arm Neck Tension Adjustment
Use Allen key (5mm) provided to adjust tension to correspond with weight of monitor. Twist Allen key in a clockwise direction for heavier monitors; counterclockwise for lighter monitors. NOTE: Support arm while adjusting tension.
8

MONITOR ARM

9 | Arm Elbow Tension Adjustment
Use Allen key (4mm) provided to adjust tension to correspond with weight of monitor. Twist Allen key in a clockwise direction for lighter monitors; counterclockwise for lighter heavier monitors. NOTE: Support arm while adjusting tension.
9

10

END OF MONITOR ARM SECTION

A1: Laptop tray Overview
Series II Monitor Arm All parts listed are for a single laptop tray;
additional parts will be needed for additional laptop trays.
11

LAPTOP TRAY

Parts List

Code

Qty.

Description

1

Laptop Tray

NXLT

2

Swath Adhesive Pad

1

Round Adhesive Pad

4

Machine Screw

4

Hex Nut

1

Allen Key (2.5mm)

1

Wrench

12

LAPTOP TRAY

1 | Install Adhesive Pads
Paste round shape pads on both adjustable clamps. Then, paste swath pads on lip of laptop tray.
2 | Attach Laptop Tray to Monitor Arm
Use Allen key (2.5mm) and wrench to adjust screws and nuts on the monitor plate adapter.
13

END OF LAPTOP TRAY SECTION

3 | Adjust Clamps to Fit Laptop Size
Use the knobs to adjust clamps for suitable wide range laptop size.
4 | Optional: Use Keyhole to Include 3rd-Party Lock
NOTE: Lock not included.
14