Juniper THREE60 Conference Table Installation Guide

: September 5, 2024
: JUNIPer

Table of Contents

THREE60 Conference Table
Specifications:
Product Usage Instructions:
Sitting Height (S1):
Standing Height (S2):
- Frequently Asked Questions (FAQ):
Q: Are additional parts needed for multiple standing height
Q: Is the covered sleigh leg necessary for wire

THREE60 Conference Table

“`html

Specifications:

Product Name: THREE60 Conference Table
Includes Add-Ons: S1 | S2 | S3
Table Size: 48 x 216

Product Usage Instructions:

Sitting Height (S1):

Prepare Surface and Measure for Legs:
Carefully place the surface upside-down on the floor. Measure 12″
from the surface edge and center-align to determine leg
placement.
Secure Angled Sleigh Legs: Follow measurements
and insert screws per leg through the metal plate and into the
laminate surface.
Measure for Cabinet Base or Covered Leg: Place
cabinet base or covered leg centered under table grommet
cutouts.
Install Cabinet Base or Covered Leg: Insert 4
screws per base through the laminate top into the bottom of the
surface.
Attach Hardware to Surface Edge: Insert 2
wooden dowels, attach 2 flat brackets, and connect 4 sets of joint
fasteners to one side of each surface edge.
Flip and Assemble: Flip each piece over so
that it is standing on a leg/cabinet base. Align open holes on the
surface edge with wooden dowels and threaded rods on the other
surface edge.
Fully Secure Hardware: Install wire management
grommet.

Standing Height (S2):

Prepare Surface: Carefully place the surface
upside-down on the floor. Measure 12″ from the surface edge and
center-align to determine leg placement. Attach 2 flat brackets on
the center seam of the table.
Install Angled Sleigh Legs: Follow
measurements and insert 15 screws per leg through the metal plate
and into the laminate surface.
Install Support Brace
Flip and Insert Grommet: Insert wire
management grommet.

Frequently Asked Questions (FAQ):

Q: Are additional parts needed for multiple standing height

tables?

A: Yes, additional parts will be required for each additional
standing height table beyond the first one. Refer to the product
manual for specific part numbers and quantities.

Q: Is the covered sleigh leg necessary for wire

management?

A: The covered sleigh leg is optional for wire management
purposes. It aligns with the grommet cutout on the table, providing
an alternative solution for managing wires.

“`

THREE60
Conference Table
Includes Add-Ons: S1 | S2 | S3
General Installation Guide

TABLE OF CONTENTS

Sections
S1 :: Sitting Height …………………………………………………………………………. 1 S2 :: Standing Height …………………………………………………………………… 9 S3 :: Optional Power…………………………………………………………………… 15

S1: Sitting Height Overview
THREE60 Conference Table Quantities are for a 48″ x 216″ table, parts may
vary depending on project, but install steps will remain same.
1

SITTING HEIGHT

Parts List

Code

Qty.

Description

GCNAB

2

Angled Sleigh Leg

1

Trapezoid Surface

CNS48144

2

In-Surface Grommet

CNCGB

2

Center Grommet Spacers

2

In-Surface Grommet

CNCBV2

4

BFB1

6

GCNABCOV*

4

Cabinet Base Flat Bracket Covered Leg

*If applicable.

2

SITTING HEIGHT

1 | Prepare Surface and Measure for Legs
Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12″ from surface edge and center-align to determine leg placement. NOTE: Same process for square-ended table.
12″
2 | Secure Angled Sleigh Legs
Follow measurements and insert screws per leg through metal plate and into laminate surface.
3

SITTING HEIGHT

3 | Measure for Cabinet Base or Covered Leg
Place cabinet base, or covered leg, centered under table grommet cutouts.
5.91″
9.45″

9.45″

5.12″

4

SITTING HEIGHT

4 | Install Cabinet base or covered Leg
Insert 4 screws per base through laminate top into bottom of surface.
5 | Attach Hardware to Surface Edge
Insert 2 wooden dowels, attach 2 flat brackets, and connect 4 sets of joint fasteners to one side of each surface edge.
Surface Edge
5

SITTING HEIGHT

6 | Flip and Assemble
Flip each piece over so that it is standing on a leg/cabinet base. Align open holes on surface edge with wooden dowels and threaded rods on other surface edge.

7 | Fully Secure Hardware

1. Set Hardware

Turn to Tighten

2. Tighten Hardware

Hold Still

6

SITTING HEIGHT

8 | Install Grommets
Insert wire management grommet.
7

8

END OF SITTING HEIGHT SECTION

S2: Standing height Overview
THREE60 Conference Table All parts listed are for a single standing height table;
additional parts will be needed for additional standing height table.
9

STANDING HEIGHT

Parts List

Code

Qty. Description

GCNABSH

2

Standing Height Angled Sleigh Leg

CNS4896

1

Main Surface

1

In-Surface Grommet

GCNABSHLE

2

Support Brace

BFB1

2

Flat Brackets

10

STANDING HEIGHT

1 | Prepare Surface
Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12″ from surface edge and center-align to determine leg placement. Attach 2 flat brackets on center seam of table. NOTE: Leg placement may need to be adjusted based on surface size.
12″
2 | Install Angled Sleigh Legs
Follow measurements and insert 15 screws per leg through metal plate and into laminate surface.
11

STANDING HEIGHT

3 | Install Support Brace
4 | Flip and Insert Grommet
Insert wire management grommet. Note: See page 13 for optional covered sleigh leg. See page 15 for power module install.
12

STANDING HEIGHT

Optional Covered Sleigh Leg
All steps for installation are the same. However, leg will be aligned with grommet cutout on the table. NOTE: Covered sleigh leg is optional for wire management.

9.45″

5.12″

13

14

END OF STANDING HEIGHT SECTION

S3: Optional Power Overview
THREE60 Conference Table
15

OPTIONAL POWER

Parts List

Code

Qty.

BPCONF2V2 or BPCONF3

1

Description In-Surface Power Module

JC1

5

J-Clips

VB24

1

Cable Vertebrae

16

OPTIONAL POWER

1 | Attach Metal Clips and Insert into Surface
Attach 2 metal clips to back of module base then insert into pre-cut holes in surface.
17

OPTIONAL POWER

2 | Secure Module into Place
Insert plastic clamps into holes on bottom of module. Rotate and then push against surface to clamp module into place.

1. Clamp

2. Rotate

3. Push

18

OPTIONAL POWER

3 | Optional Power Vertebrae
Attach vertebrae to underside of top panel. Insert wood screws through top bracket and into laminate panel. NOTE: Power vertebrae will be mounted adjacent to power module.
19

20

END OF OPTIONAL POWER SECTION