Juniper CV-1 Focus Pod Installation Guide

Juniper CV-1 Focus Pod

Product Specifications

• Model: CV-1
• Product Name: Focus Pod
• Material: Steel dowels, panels

Product Usage Instructions

1. Secure Connecting Steel Dowels to Panels
   Insert connecting steel dowel plate into marking hole and insert four 3/4 screws through flat plate to secure. Repeat step for all 4 steel dowels.

2. Insert Steel Dowels into Joint Holes
   Line up steel dowels so that they are flush with joint holes on adjacent panel. Push against outer walls of pod until panels are flushed.

3. Secure Panels
   Adjust panel bracket, attached to the bottom of the panel, so the open end fits around the stand-alone bolt on the bottom of the adjacent panel.

4. Connect Main Power
   Assemble connector joint by securing male and female halves together and secure with connector clips on top and bottom of the assembly.

5. Secure Connecting Steel Dowels to Top Panel
   Insert connecting steel dowel plate into marking hole on the bottom side of the top panel and insert four 3/4 screws through the flat plate to secure. Repeat step for all 10 steel dowels.

6. Connect Power to Top Panel
   Assemble connector joint by securing male and female halves together and secure with connector clips to the top and bottom of the assembly. Once connected, tuck the completed assembly into the slot at the top of the side panel.

7. Secure Top Panel
   Line up steel dowels so they are flush with joint holes on the adjacent panel. Push against outer walls of pod until panels are flushed.

8. Secure Leg to Table
   Secure 4 screws through pre-drilled table base holes and into the bottom of the table surface.

9. Place Seats Inside Pod
   Tilt seat at a 45-degree angle. Slide into pod while tilting seat back so the seat sits flat on the floor.

10. Position Table inside Pod

Frequently Asked Questions

Q: How do I disassemble the Focus Pod?
A: To disassemble the Focus Pod, follow the installation steps in reverse order, unscrewing and disconnecting components carefully.

Foc us Pod

General Installation Guide

1. Secure Connecting Steel Dowels to Panels
   Insert connecting steel dowel plate into marking hole and insert four 3/4” screws through flat plate to secure. Repeat step for all 4 steel dowels.

2. Insert Steel Dowels into Joint Holes
   Line up steel dowels so that they are flush with joint holes on adjacent panel. Push against outer walls of pod until panels are flushed.

3. Secure Panels
   Adjust panel bracket, attached to bottom of panel, so open end fits around stand-alone bolt on bottom of adjacent panel.

4. Connect Main Power
   Assemble connector joint by securing male and female halves together and secure with connector clips on top and bottom of assembly.

5. Secure Connecting Steel Dowels to Top Panel
   Insert connecting steel dowel plate into marking hole on bottom side of top panel and insert four 3/4” screws through flat plate to secure. Repeat step for all 10 steel dowels.

6. Connect Power to Top Panel
   Assemble connector joint by securing male and female halves together and secure with connector clips to top and bottom of assembly. Once connected, tuck completed assembly into slot at top of side panel.

7. Secure Top Panel
   Line up steel dowels so they are flush with joint holes on adjacent panel. Push against outer walls of pod until panels are flushed.

8. Secure Leg to Table
   Secure 4 screws through pre-drilled table base holes and into bottom of table surface.

9. Place Seats Inside Pod
   Tilt seat at a 45 degree angle. Slide into pod while tilting seat back so seat sits flat on floor.

10. Position Table inside Pod

1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com
© 2023 Juniper Office | Version 23.0.0

References

• Juniper | Office Furniture for the Entire Workspace

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>