Flexabed Wireless Premier Beds Instruction Manual
- September 3, 2024
- Flexabed
Table of Contents
- Wireless Premier Beds
- Product Information
- Specifications:
- 1. Bed Setup
- 2. Leg Extensions Installation
- 3. Power Connection
- 4. Mattress Retainer Bar Installation
- 5. Attaching a Headboard
- Q: Does the bed come with safety rails?
- Q: Can I adjust the height of the bed?
- Q: How should I protect the bed from power surges?
Wireless Premier Beds
“`html
Product Information
Specifications:
- Product: Wireless Premier Beds
- Manufacturer: Flexabed
- Website: www.Flexabed.com
Product Usage Instructions
1. Bed Setup
Remove any shipping items attached to the bed, such as hardware
carton, leg pads, and safety rails. Install casters or leg pads
into each bed leg.
2. Leg Extensions Installation
If you have optional leg extensions, insert them into the welded
legs. Then install leg pads or casters into the threaded insert of
the leg extension.
3. Power Connection
Plug in the power supply and check all cable connections. Use a
surge protector to prevent damage from power surges.
4. Mattress Retainer Bar Installation
If necessary, install the mattress retainer bar by aligning it
with the bolts underneath the foot end of the bed and securing it
with wing nuts.
5. Attaching a Headboard
If desired, attach a headboard using the factory-installed
headboard mounting brackets. Adjust the brackets outward by
removing nuts and bolts per bracket.
Frequently Asked Questions (FAQ)
Q: Does the bed come with safety rails?
A: Safety rails are optional and need to be removed from the
frame if ordered.
Q: Can I adjust the height of the bed?
A: Yes, optional leg extensions are available in different
lengths to raise the overall height of the bed.
Q: How should I protect the bed from power surges?
A: It is recommended to plug the bed into a surge protector to
prevent damage to electronic components.
“`
Operations Manual
FOR WIRELESS PREMIER BEDS
www.Flexabed.com
1
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW FLEXABED!
Your Flexabed was custom built by skilled craftsmen in Lafayette, GA using the
same principles of quality that we have built our reputation on since 1969.
Our beds provide multilevel support in literally thousands of positions for
sleeping, watching television, reading or simply relaxing. Should you ever
experience technical problems with your Flexabed, simply call our customer
service department at 1-800-648-1256
and we will make sure you are resting comfortably again in no time! Please
take notice of your bed’s serial number below. If you ever need to call our
customer service department, this serial number will allow us to diagnose your
issue accurately and efficiently. Your serial number is the number on the
first line of the label below.
2
Remove any items attached to the bed for shipping purposes.
First remove the hardware carton that is stapled to the underside of the bed
(Fig. 1). The hardware carton contains your hand control, casters and/or leg
pads, leg extensions (if ordered), and bed literature. Next, remove the wooden
leg pads that are inserted into each bed leg. Finally, if you ordered safety
rails, remove the rails from the frame. Each safety rail is zip tied to the
bed frame.
Install your casters or leg pads in to each bed leg.
If installing casters, insert the caster into the threaded insert on each bed
leg. Next, using your fingers, thread the caster into the bed leg by rotating
the hex nut (Fig. 2a). Once you can no longer use your finger to tighten the
caster, use a ½” wrench to finish tightening the caster in to the bed leg
(Fig. 2b). FAILURE TO FULLY THREAD AND TIGHTEN CASTERS WILL RESULT IN DAMAGE
TO THE CASTERS THAT IS NOT COVERED UNDER WARRANTY! Once the bed is turned
upright, you can lock each caster by depressing the locking lever on each
caster (Fig. 2c).
If you ordered leg pads instead of casters, insert each leg pad into the
threaded insert on each bed leg. Hand tighten the leg cap in the bed leg until
it is flush with the hex nut (Fig. 3). You can adjust each leg pad as needed
to level the bed.
SIDERAILS
HARDWARE CARTON
CASTER INSTALL
FIG. 1 CASTER INSTALL
FIG. 2A CASTER INSTALL
FIG. 2B LEG CAP INSTALL
FIG. 2C
FIG. 3
3
Install Your Optional Leg Extensions.
Leg extensions are available in one inch increments from 2″ to 7″ which allows you to raise the overall height of the bed. Leg extensions are an optional accessory item.
If you ordered leg extensions that are 5″ or less in length, they will be located
inside the hardware carton that is stapled to the underside of the bed. If you
ordered 6″ or 7″ leg extensions they will be attached to the top side of the
FIG. 4
hardware carton.
To install the leg extensions, make sure the bed is either in an upside down
position or propped on its side. The four (six if reinforced) legs that are
welded to the bed frame will be hollow inside. The leg extensions have one end
that is rounded. Insert the rounded end of the leg extension into the hollow
square welded legs on the bed frame as seen in Fig 4. While adding pressure,
slide the leg extension into the hollow square frame leg until the square
section of the leg extension is flush with the welded leg as seen in Fig 5.
Once all of your leg extensions are fully inserted into the welded legs, you
can proceed to step 3 and install your leg pads or casters into the threaded
insert of the leg extension.
FIG.5
4
Plug in power supply and check all
cable connections.
Your bed’s power supply is mounted to the head platform section underneath the
bed. Insert the electrical plug from the power supply (Fig. 6) in to a
standard 110/120 volt household electrical outlet. The power supply has a
small indicator light that will illuminate green if it is properly receiving
electrical power. If you have plugged the power supply in to a wall receptacle
and the indicator light does not illuminate green, you will need to check your
cable connections and your wall receptacle. All electrical and motor cables
should already be connected to their appropriate sources when the bed is
shipped from the factory. In the event that your bed is not operating
properly, refer to “Cable Connections” in this owner’s manual to diagnose
possible issues with your bed .
We strongly recommend that that you plug your bed into a surge protector to
prevent damage to the bed’s electronic components in the event of a power
surge in your home’s electrical system. Flexabed’s warranty does not cover
damages to the bed as a result of a power surge.
PLUG IN TO ELECTRICAL OUTLET
PLUGS IN TO “POWER” PORT ON CONTROL BOX
FIG. 6
5
FIG. 7
FIG. 8
FIG. 9
6
Install mattress retainer bar (if necessary).
If you ordered a foundation with a standard-sized mattress this step is not
necessary as the mattress retainer bar is installed at the factory. HOWEVER,
if you ordered a foundation only or a foundation and a low profile mattress,
you will need to install the mattress retainer bar before using the bed. The
mattress retainer bar secures the mattress in place when the bed is flexed and
prevents the mattress from sliding off the foundation. Raising the foot
section of the bed with your hand control will make this installation easier.
Underneath the foot end of the bed, there will be 4 bolts with a wing nut
attached. Unscrew the 4 wingnuts and align the holes on the mattress retainer
bar with the bolts. (Fig. 7) Once the mattress retainer bar is properly
aligned, hand tighten the 4 wing nuts to the bolts to secure the mattress
retainer bar in place. (Fig. 8) Place the mattress retainer bar cover (found
in the mattress bag) over the mattress retainer bar. (Fig. 9)
OPTIONAL
Attaching a Headboard
Your Flexabed does not require a headboard but is equipped with factory
installed headboard mounting brackets should you wish to attach one for
decorative purposes.
The headboard brackets have been mounted at the factory facing inward for
convenient shipping as pictured in Fig 10. In order to attach a headboard, it
will be necessary to remove 2 nuts and bolts per bracket and turn the brackets
outward as seen in Fig 11.
There are four holes in the metal bed frame that allow you to adjust the
brackets outwards to meet your individual headboard configuration. The
brackets are made from mild steel so that they can be bent to accommodate
customized positions for your headboard.
When attaching two twins to a king-sized headboard, it is only necessary to
prepare the outside brackets for use.
FIG. 10 FIG. 11
7
FIG. 12
Install Safety Rails (if ordered).
All Flexabed Premier models ordered with safety rails (except 30″ Split beds)
come factory equipped with a plate mounting system that facilitates a quick
and sturdy installation of your Flexabed safety rails. The only tool needed to
complete a safety rail installation is a 9/16″ wrench.
1. Raise the head section of the bed to the most upright position using your hand control. If installing safety rails at the foot section, then also raise the foot section to the most upright position. ON TWIN BEDS, FAILING TO RAISE THE HEAD AND/OR FOOT SECTIONS OF THE BED BEFORE INSTALLING SAFETY RAILS CAN CAUSE SERIOUS DAMAGE TO YOUR BED AND DAMAGES CAUSED BY IMPROPER SAFETY RAIL INSTALLATION ARE NOT COVERED UNDER WARRANTY!
FIG. 13
2. Locate the 2 bolts and nuts on the underside of the foundation approximately 1″ from the edge of the bed. (Fig. 12)
3. Completely remove the nuts from the bolts using a 9/16th socket wrench.
4. Whether installing safety rails at the head-end of the bed or the foot-end
of the bed, place the hole in the middle of the “L” shaped bracket on the
bolts making sure that the label on the safety rail with an arrow is pointing
towards the center of the bed. (Fig. 13)
FIG. 14
8
5. Replace the nuts removed in step c and tighten them down with a 9/16″
wrench. (Fig. 14)
REMEMBER…your Flex-A-Bed side rail can be lowered to allow for easy entry to
and from the bed. Simply pull UP on the side rail and swivel the side rail to
the lowered position. (Fig. 15 & 16)
When installing safety rails on a twin sized Hi-Low bed, the brackets will
contact the metal bed frame when in the lowered position. This is normal and
does not void your warranty.
If you ordered safety rail covers, you can install the cover with the pocket
facing inward or outward depending on your preference. (Fig. 17). Pull the
safety rail over the safety rail by stretching the cover slightly.
FIG. 15 FIG. 16
FIG. 17
9
Remote Flashlight Programmable Memory # 1
Button Not Used Head Up Foot Up
Programmable Memory # 3 Head Massage Control Massage Timer Selector Massage
System On/Off
10
Only used when pairing a new remote Programmable Memory # 2
Button Not Used Bed Flat Foot Down Head Down Programmable Memory # 4
Massage Timer Indicator Lights Foot Massage Control Massage Mode Selector
Underbed Light On/Off
TO PROGRAM A PROGRAMMABLE MEMORY BUTTON Adjust the bed to your desired
position. Once desired position is reached, press and hold the programmable
memory button for 5-7 seconds until all buttons on the remote flash rapidly
then release.
MASSAGE SYSTEM CONTROL For beds equipped with massage, the massage system can
be turned on/off by pressing the “On/Off ” button. Choose between a constant
or pulsating mode by pressing the “Mode” button.
MASSAGE TIMER CONTROL When activated, the massage system will automatically
shut off after a specified period of time. The system can be programmed to
shut off after 10, 20 or 30 minutes by pressing the timer button
FLAT BUTTON Press and release the “Flat” button to return all motors on the
bed to the flat and level position
UNDERBED LIGHT CONTROL For beds equipped with an underbed LED lighting system,
press the underbed light button to turn the light system on or off.
PREMIER HAND COTROL FLASHLIGHT:
Press and hold the flashlight button and your remote instantly becomes an LED
flashlight! To turn the flashlight off simply release the button.
MASSAGE SYSTEM (if equipped):
All Flexabed Premier remotes come with massage operation buttons whether your
bed was ordered with massage or not. If you did not order a massage option
when you purchased your bed then all of the massage-related buttons will not
be operable. If desired, you can order a massage system from your Flexabed
dealer.
To activate the massage system, press the “ON/OFF” BUTTON. This will activate
both head and foot massage motors in the “constant” mode.
Once engaged, your Flexabed massage system will operate on a
timer system where the massage motors will automatically turn off after a
specified time. The massage system can be programmed to turn off automatically
after 10, 20 or 30 minutes. To change the timer duration, press the “Timer”
button to move the blue light above the different timer durations on the
remote.
Both the head and foot massage motors have three intensity settings: low,
medium and high. You can adjust the intensity setting on either massage motor
by pressing the “Head” or “Foot” button one time for each level of intensity
you want to adjust. You can turn either of the massage motors off by
continuing to press the “Head” or “Foot” button for the motor that you want to
deactivate.
To activate the pulse massage mode, press the “Mode” button. The pulse massage
has three different speeds. Press the “Mode” button one time to change the
speed of the pulse massage mode.
11
UNDERBED LIGHTING (if equipped):
All Flexabed Premier remotes come with an underbed lighting control button
whether your bed was ordered with underbed lighting or not. If you did not
order underbed lighting when you purchased your bed the underbed lighting
control button will not be operable. If desired, you can order an underbed
lighting system from your
Flexabed dealer. If your bed is equipped with an underbed lighting system, two
motion sensors come pre-installed from the factory that will automatically
turn the underbed lights on if motion is detected. The motion detectors come
installed diagonally across from each other on two bed legs but can be moved
to accommodate your specific needs.
MEMORY POSITIONS:
Your Flexabed allows you to store 4 of your own custom memory positions. To
program your custom memory position you will need to do the following:
·Adjust the bed to the position you want to save to memory
·Press and hold one of the four programmable memory buttons (M1, M2, M3 or M4)
for 5-7 seconds
·After holding the memory button for 5-7 seconds, all of the buttons on the
remote should flash rapidly. Once the buttons flash, release the memory button
to complete the programming process.
12
13
FIG. 18
SYNC BUTTON
PAIR/SYNC BUTTON
HAND CONTROL SYNCING (wireless remote only):
If your bed is equipped with a wireless remote, the remote is automatically
synced to your bed at the factory during the manufacturing process. In the
event that you order a new replacement remote or a new control box in the
future, you will have to sync the wireless remote to your control box. To sync
a wireless remote to your control box:
· Press the “Pair” button twice on the control box underneath the bed. (Fig.
18) After pressing the “Pair” button twice, the light should change from green
to blue.
· Once the pairing light has changed from green to blue, press and hold the
“Pair” button on your remote control for 3-5 seconds. The lights on the remote
should blink rapidly and the pairing light on the control box should change
from blue to green indicating your remote has been successfully paired.
14
Backup battery power:
Each Flexabed power supply is equipped to supply emergency bed lowering
capability via battery power. EMERGENCY BATTERY POWER IS OPTIONAL THE BED
WILL FUNCTION PROPERLY WITH OR WITHOUT BATTERIES IN THE POWER SUPPLY.
In order to use backup battery power, you will need to install two 9V
batteries (not included) into the emergency battery compartment (Fig. 19)
These batteries should be replaced periodically to insure proper operation in
the event of loss of electrical power to the bed. The emergency battery
compartment is located on the side of the power supply. (Fig. 19)
In the event of a loss of electrical power, the emergency battery power will
allow you to LOWER the bed to a flat position. Battery backup power DOES NOT
PROVIDE SUFFICIENT POWER TO RAISE THE BED. If you desire to have the
capability to raise the bed in the event of a loss of electrical power, you
will need an alternative power source such as a generator.
image here
TWO 9V BATTERIES
FIG. 19
15
CABLE CONNECTIONS
As stated earlier in this manual, all cables are set up and connected at the
factory when your Flexabed is built.
However, those cables can become disconnected during the shipping and delivery
process. Also, there may be a point in time during the life of your Flexabed
where you need to replace a component of the motor system. The purpose of
these instructions is to help you properly connect all cables and connections
on your bed to ensure proper operation.
If your bed is not working, the most common problem we find in our customer
service department is that the bed is not receiving electrical power. Before
you check the connections on the bed, always check the following:
· Make sure the power cord from the bed is plugged in properly to a wall
receptacle or a power strip/surge protector.
· Check to make sure the electrical outlet that you are using to supply power
to your bed and/or power strip is in working order. It is a good idea to plug
a known working electrical device (i.e. lamp, radio, etc) into the outlet to
test whether the outlet is providing electrical power. If not, check to make
sure the breaker is not tripped for the outlet’s electrical circuit.
· Flexabed recommends plugging your bed(s) into a UL-approved power strip or
surge protector. However, if you are doing this, make sure that your power
strip/surge protector does not have too many devices plugged in that exceeds
the manufacturer’s specifications. If your bed is plugged in to a power
strip/surge protector and is not receiving power, it is always a good idea to
plug the bed directly into a wall receptacle. If the bed works while plugged
into a wall receptacle but now when plugged into a power strip/surge
protector, the problem lies within your power strip/surge protector and not
the bed.
16
1. Power Supply Connections.
The first place to check your wiring connections is at the power supply. Your
bed’s power supply is attached to the bed’s platform on the underside of the
head section of the bed. The power supply is a small black box that plugs in
to your home’s wall receptacle to supply electrical power to the bed. The
power supply has a small indicator light that will illuminate green if there
is power being supplied. If the indicator light is not illuminated, check the
following two connections that are located on opposite ends of the power
supply: (Fig 6)
· Power cord connection this is the cable that plugs directly in to your
wall receptacle. Check and make sure the cable is plugged in securely to the
power supply.
· Extension cable connection This cable runs from the power supply to the
bed’s control box on the underside of the bed. Check to make sure the cable is
plugged in securely to the power supply and the control box. There is a port
labeled “Power” on the control box. The extension cable should be plugged into
the “Power” port on the control box.
PLUG IN TO ELECTRICAL OUTLET
PLUGS IN TO “POWER” PORT ON CONTROL BOX
FIG. 6
17
CONTROL BOX PORTS
18
2. Control Box Connections.
The control box is the “brain” of your Flexabed which allows the hand control to communicate with all of the motors on your bed. If any motor or accessory item on your bed is not working, check all of the ports on the control box to make sure that connections are configured properly. (Fig. 20)
· Head the head motor should be plugged into this port
· Foot the foot motor should be plugged into this port
· Lumbar nothing should be plugged into this port
· Tilt nothing should be plugged into this port
· Massage 1 the head massage motor should be plugged into this port
FIG. 20
· Massage 2 the foot massage motor should be plugged into this port · MFP2 any accessory items such as the voice control module or the underbed light
motion sensor will plug into the port. If you have not ordered any of these items, nothing will be
plugged into this port.
· Sync only used if you have ordered a sync cable to synchronize two separate beds
· Underbed light this port is only used if you have ordered an underbed lighting system
· MFP1 this port is not used
· Power the extension cable coming from the power supply should ALWAYS be plugged into this port
· Pair Button this is only used to sync a new remote to your bed. All remotes are automatically synced at the factory. This button should only be used to sync a replacement remote with your bed.
19
VOICE ACTUATION CONTROL
The voice control module (VCM) allows a bed user to control all of the
functions on their Flexabed without
the use of a traditional hand-held remote control. The voice control module
should be placed on a nightstand or other flat surface that is in close
proximity to your Flexabed. The VCM needs to have a clear path to the bed user
so that verbal commands from the user can be clearly heard and understood by
the VCM.
The VCM has a male and female voice programmed to receive voice commands from
the bed user. The male voice is “Max” and the female voice is “Susan”. You can
select the voice that is most preferable in your situation.
In addition to voice actuation control, the VCM also has the ability to charge your mobile devices via a wired and wireless connection. There is a standard USB-A port and a USB-C port on the face of the VCM for wired charging of your mobile device. You can also place your mobile device on the lightning bolt logo on top of the VCM for fast wireless charging!
20
The VCM is automatically programmed to “Max” at the factory. To give the VCM a
verbal command, you must: Step 1: “wake” the VCM by saying, “Hello Max” or
“Hello Susan”. The VCM will illuminate with a blue ring at the top of the
module to indicate that it is awake.
Step 2: Once the VCM is awake, you can speak any of the following voice
commands:
Remember, the VCM must be “awake” before it can accept any voice command. If
you are speaking the command and the bed does not respond, simply wake the VCM
up
by saying “Hello Max” or “Hello Susan”.
V O I C E C O M M A N D S (words in parentheses are for instruction only – they are not spoken)
Head Up Head Down Foot Up Foot Down
Save Position 2 Save Position 3 Save Position 4 Massage Start
Timer 10 (to set massage timer to 10 mins)
Timer 20 (to set masssage timer to 20 mins)
Timer 30 (to set massage timer to 30 mins)
Lights On
Stop All (stops all motors) Flat Position
Position 1
Position 2
Position 3
Position 4
Save Position 1
Massage Stop
Lights Off
Wave 1 (massage wave intensity level 1)
Wave 2 (massage wave intensity level 2)
Wave 3 (massage wave intensity level 3)
Wave 4 (massage wave intensity level 4)
Level 1 (massage intensity level 1)
Level 2 (massage intensity level 2)
Level 3 (massage intensity level 3)
Level 4 (massage intensity level 4)
Toggle Light
Volume Up (controls the volume of Max/Susan voice) Volume Down (controls the
volume of Max/Susan voice) Max Volume
Minimum Volume
Silent Mode (turns off Max/Susan’s voice) Switch Name To Susan (if current
voice is Max) Switch Name To Max (if current voice is Susan)
21
BLUETOOTH CONNECTION MANUAL OF SMARTBED APP
1. Installation Instruction
Download the SmartBed app by scanning the following QR code, or search OKIN
SmartBed in App store: IOS (App store),Android(Google play/Huawei app store).
BLUETOOTH CONNECTIVY:
Your Flex-A-Bed can be controlled with any Bluetooth enabled Android or Iphone
device by downloading the Okin SmartBed app. To download the SmartBed app,
scan the following QR code or search “Okin SmartBed” in your phone’s App
store. Once the SmartBed app has been downloaded, open the app and perform the
following steps:
· You will first need to create an online account with Okin. Follow the
prompts on the app to create your account
· Enable Bluetooth connectivity on your phone/device
App Store
22
Huawei App Goggle Play
FIG. 21
FIG. 22
FIG. 23
· Navigate to the screen titled “POSITION” (Figure 21)
· Click on the 3 horizontal bars in the upper left corner of the screen
· At the bottom of the screen, select the “Bluetooth” option (22)
· You should see a device named “SmartBed” in the device list. Click on the
Smart Bed device to pair your device with your bed. If the “SmartBed” is not
found in the device list, press the back button to return to the “Position”
screen and then re-enter the device screen by clicking on the three horizontal
bars.
· Once connected, there are three screens you can side swipe to explore. The
screens are titled:
· “Position” (Figure 23) this menu contains all of the various controls for
changing the position of your bed
· “Massage” (Figure 24) this menu contains all of the control functions for
your bed’s massage system
· “Alarm” (Figure 25) in this menu you can set alarms to automatically wake
you by using a control function on the bed such as a moving to a memory
position or activating the massage system
FIG. 24
FIG. 25
23
POSITION SCREEN.
The position screen is similar to the layout on your remote control with a few
exceptions.
BUTTON
Head Up Head Down H&F Up H&F Down Foot Up Foot Down Head Tilt Up Head Tilt
Down Lumbar Up Lumbar Down Flat ZG Lounge TV / PC
Anti-Snore
Memory
Light
FUNCTION
Move head motor up Move head motor down Move head & foot motor up Move head &
foot motor down Move foot motor up Move foot motor down Not used Not used Not
Used Not Used Return all motors to flat position M1 Memory Position M2 Memory
Position M3 Memory Position
M4 Memory Position
Extra Programmable Memory Position (app only) Turn underbed light system
on/off
24
Your regular remote only has four programmable memory buttons (M1, M2, M3,
M4). When using the Smart Remote app, you get a fifth programmable memory
button titled “Memory”. This position is not available on your regular remote.
To program any of the memory positions within the Smart Remote app, perform
the following steps:
· Adjust your bed to the desired position · Press and hold any of the five
programmable memory
buttons for 5-7 seconds until you see a message on the screen that says
“Memory Save Success”. Once you see the message “Memory Save Success” you can
release the button and the position is saved.
If you press a programmable memory button and the bed does not go to the exact
position that you programmed, press the programmable memory button a second
time and the bed should continue to the programmed position. It is common for
the bed to sometimes stop short of the programmed position if there is
electrical interference with the communication system.
MASSAGE SCREEN
This screen allows you to change the settings on your bed’s massage system
using the Smart Remote app. (Figure 24)
· Press the ON/OFF button turn the massage system on or off. If the massage
system is off, the timer, intensity, and type functions cannot be adjusted.
· Press the left or right arrows on the HEAD INTENSITY meter to adjust the
intensity of the head massage motor. There are three different intensity
settings to choose from and will be indicated by a green status bar.
· Press the left or right arrows on the FOOT INTENSITY meter to adjust the
intensity of the foot massage motor. There are three different intensity
settings to choose from and will be indicated by a green status bar.
· Press the left or right arrows on the TYPE meter to choose between the three
different pulse massage modes which will be indicated by a green status bar: º
Mode 1 = Slow Pulse º Mode 2 = Fast Pulse º Mode 3 = Faster Pulse
ALARM SCREEN
The alarm screen allows you set an alarm for a specified time and day(s) of
the week that will wake you by using one the bed’s functions such as moving
the bed to a memory position, activating the massage system or turning on the
bed’s underbed light system. (Figure 25) To set an alarm:
· Make sure the blue button on the bottom of the screen says “Turn on & Save”.
If the blue button says “Turn off & Edit” you must press the blue button again
until the button reads “Turn on & Save” in order to edit the alarm settings.
· First set the time of day you want the alarm to wake you. The clock is set
in a 24 hour format with the hours on the left and the minutes on the right.
For example, to set an alarm for 2:30 pm, set the hours to 14 and the minutes
to 30. You can change the hours and minutes by scrolling the desired time with
your finger on the screen.
· For the Repeat setting, choose the day(s) of the week you would like the
alarm to wake you
Continued on page 26 25
MASSAGE SCREEN (Continued)
· For the Wake up type setting, choose which of the bed’s functions you would
like to wake up to. You can only choose one function. For instance, if you
want the bed to wake you up by moving the bed to the M2 memory button setting,
select the “Lounge” option. If you want the massage motors to come on to wake
you, select the “Massage” option.
· For the Sound setting, choose which alarm sound, if any, you wish for your
mobile device to play when the alarm goes off. The alarm sounds are short
ringtones played by your device to gently wake you at the desired time.
· When you are finished editing your alarm settings, press the blue button at
the bottom of the screen that says “Turn on & Save”. Once you press the “Turn
on & Save” button, the small alarm clock icon at the top of the screen will
illuminate green to indicate the alarm is set and ready.
26
PREMIER WIRELESS BED
Limited Lifetime Warranty
Because Flexabed builds every bed by hand, we stand behind our product with a
great warranty.
This warranty covers the entire bed–each and every component and design
feature (even the mattress!), without exception.
BEST OF ALL
Our warranty is even transferable. It’s not limited to the person who
purchases the bed. So if you sell or give the bed to someone else, it remains
under warranty.
This warranty does not apply to any product subjected to customer misuse,
electrical surges, damage in transit or handling by the delivering agent
unless the customer signs the bill of lading with damages noted, or which, in
the opinion of Flexabed, has been altered or repaired by an unauthorized
representative in any way that affects the reliability or detracts from the
performance of the product. Replacement parts are warranted for the unexpired
balance of the original warranty period. This warranty does not include
responsibility for transportation or handling expenses except those specified.
The foregoing is in lieu of all other warranties, expressed, implied, or
statutory. Flexabed neither assumes nor authorizes any person to assume for it
any other obligation or liability in connection with the sale of this
product. In the unlikely event that critical repair components become
impossible to acquire after the 5th year and a repair cannot be made, Flexabed
will offer an “in-lieu of” discount of 33% off the MSRP that is in effect at
that time toward the purchase of a new mattress or articulating base unit.
In order to prove a defect in materials or workmanship, the customer will be
expected to provide pictures and/or video as prescribed by Flexabed service
personnel in order to prove the defect is not normal wear and tear on the
product.
If you experience any problem with your Flexabed at any time regardless of the
stage of your warranty, please contact us and we will make every effort to
help you.
MATTRESS AND UPHOLSTERED BASE
· During the first 12 months after purchase, Flexabed will provide in home
repairs or replacement at the factory’s option at no charge provided the
defect is demonstrated to be a defect in materials or workmanship and is more
than normal wear and tear.
· After the first year of purchase, the mattress and or the upholstered base
may be sent to the factory freight prepaid by the customer for repair,
reconditioning or replacement at the factory’s option for a $100.00 fee and
will be returned freight collect at the customer’s expense.
Note If the mattress shows unmistakable signs of abuse or wetting the
warranty is void and you will have the option to have it returned to you as-is
freight collect or discarded.
MOTORS AND LIFTING MECHANISM
· During the first 12 months after purchase, Flexabed will provide in-home
parts and labor at no charge. All parts will be shipped via UPS ground. Any
expedited charges must be paid by the customer.
· After the first year, any part may be purchased from the factory or sent to
the factory freight prepaid by the customer for repair, reconditioning or
replacement at the factory’s option for a $100.00 fee plus any shipping
charges incurred to ship the part back to the customer. 27
We’re based in friendly LaFayette, Georgia.
1-800-648-1256 | info@flexabed.com
www.Flexabed.com
28
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>