B and H AWMS-2-BT75-H Clamp Mounting System Installation Guide
- September 3, 2024
- B and H
Table of Contents
- AWMS-2-BT75-H Clamp Mounting System
- Product Information
- Specifications
- Product Usage Instructions
- 1. Assemble Post to Clamp
- 2. Fit Clamp to Work Surface
- 3. Attach VESA Plates to Displays
- 4. Slide Brackets onto Post and Set Height
- Q: Can I adjust the height of the display once it is
- Q: What should I do if my display requires a VESA adapter?
AWMS-2-BT75-H Clamp Mounting System
Product Information
Specifications
- Model: AWMS-2-BT75-H
- Clamp Size: M8x60mm screws, M8x16mm screws
- Hex Key Size: 5mm
- Compatible VESA Sizes: 75mm, 100mm
- Maximum Worksurface Thickness: 68mm (2 5/8 inches)
Product Usage Instructions
1. Assemble Post to Clamp
-
Attach the post to the upper clamp using the M8x60mm screws and
the 5mm hex key. -
Measure the worksurface thickness and select the appropriate
lower clamp position (Top, Middle, or Bottom). -
Attach the lower clamp to the upper clamp in the chosen
position using the M8x16mm screws and the 5mm hex key.
2. Fit Clamp to Work Surface
-
Place the clamp in the desired location on the
worksurface. -
If there is a small gap behind the worksurface, perform step
2.1 before proceeding. -
Screw in both pressure plates and tighten them evenly and
firmly. -
Remove clips and covers from the post by sliding them up and
out or by squeezing the sides.
3. Attach VESA Plates to Displays
-
Ensure VESA compatibility. For 75mm VESA, unscrew 5mm to access
top holes. -
Option A: Attach VESA plate with M4x10mm screws.
-
Option B: For recessed VESA, use 10mm spacers and M4x20mm
screws. -
Some displays may require a VESA adapter before attaching the
VESA plate. Check the display’s installation guide.
4. Slide Brackets onto Post and Set Height
-
The tilt bracket must only be attached with the display facing
the front of the mounting surface. -
Ensure proper positioning based on the inner guide in the rear
post channel.
FAQ
Q: Can I adjust the height of the display once it is
mounted?
A: Yes, you can slide the brackets along the post to set the
desired height for your display.
Q: What should I do if my display requires a VESA adapter?
A: If your display needs a VESA adapter, ensure to check if it
is included in the box with your display. Consult the installation
guide for further instructions on using the adapter.
1. Assemble post to clamp
1.1 Attach post to upper clamp using the M8x60mm screws and 5mm hex key.
1.2 Measure the worksurface thickness and choose the suitable lower clamp
position.
Top Middle Bottom
A
1.3 Attach lower clamp to upper clamp in the suitable position using the
M8x16mm screws and 5mm hex key.
B
C
G
H
B
F
Top Middle Bottom
2. Fit clamp to work surface
2.1 Place in desired location on worksurface.
0 – 38mm (0 – 1 1/2″) 11 – 53mm (7/16″ – 2 1/16″) 25 – 68mm (1″ – 2 5/8″)
Note: If there is only a small gap behind the worksurface perform Step 2.1 before this step
2.2 Screw in both pressure plates and tighten evenly and firmly.
2.3 Remove clips & covers from post by sliding up & out or by squeezing sides.
Mounting surface
SQUEEZE to release
5mm Hex key
3. Attach VESA plates to displays
3.1 VESA compatibility.
For 75mm VESA unscrew 5mm to access top holes
Option A Attach VESA plate with M4x10mm screws.
TOP
Option B For recessed VESA use 10mm spacers and M4x20mm screws.
100mm 75mm
75mm 100mm
NOTE: Some displays require the use of a VESA adapter before attaching the VESA plate. This VESA adapter may ship in the box with the display. Consult your display’s installation guide for further information.
E
E
J
K
L
4. Slide brackets onto post and set height
4.1 Tilt bracket must only be attached with display facing the front of the
mounting surface.
VIEW FROM ABOVE BACK of desk
INNER GUIDE in rear post channel
WORK SURFACE
WORK SURFACE
FRONT
AWMS-2-BT75-H Page 2 of 4
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>