PEMKO SDL Privacy Barn Door Lock Surface Jamb Mount Instruction Manual
- September 2, 2024
- PEMKO
Table of Contents
Opening Solutions
Experience a safer and more open world
Architectural
Door Accessories
SDL Privacy Barn Door Lock Surface Jamb Mount Instructions
SDL Privacy Barn Door Lock Surface Jamb Mount
Installation based on barn door application where doors are hung on OUTSIDE of
room.
– Install lock on jamb wall facing opening
– Install strike with an emergency release on barn door
– Adjustable strike for door thickness from 1-3/8″ to 2″
– Thick door kits available
| Part Number | Deadbolt | Thumb-Lever | Lock Case |
|---|---|---|---|
| SDL_ | 1″ | 13/16″ | 3-9/16″ x 1-7/8″ x 9/16″ |
| SDL_ -ADA | 1″ | 1-9/16″ | 3-9/16″ x 1-7/8″ x 9/16″ |
SDL Series Privacy Door Lock Set Parts:
| Items | No. | Description | Function/Privacy |
|---|
Lock
| 1| #8 x 1-1/2″ Wood Combo Screw| 4 EA
2| Mounting Plate| 1 EA
3| M3 x 7mm Handing Screw| 1 EA
4| M3 x 6mm Thumb Piece Screw| 2 EA
5| M4 x 6mm Installation Screw| 4 EA
6| Thumb Piece| 1 EA
7| , M3 x 6mm Cover Screw ,| 1 EA
8| I Lock Body Cover| 1 EA
9| Barn Door Lock Body| 1 EA
Strike| 10| Dust Proof Strike| 1 EA
11| Washer| 1 EA
12| Hollow Screw| 1 EA
Other| 13| 4mm Allen Wrench| 1 EA
14| Emergency Key| 1 EA
15| Decorative Cap| 1 EA
–| Door Prep Template| 1 EA
–| Installation Instruction| 1 EA
Tools Needed:
Prep Wall and Door
Ensure minimum 1″ (25mm) door overlap before installing SDL Privacy Lock.
Prep Jamb
Use template to mark and drill pilot holes.
Remove door if it interferes with lock installation.
Hand Lock if necessary
Install thumb lever to lock. (Fig 1)
Using a #1 Phillips screwdriver, remove handing screw and discard.
(Fig 2)
Flip lever position to opposite orientation. (Fig 2)
Install new handing screw from screw pack.
Install Lock
Attach mounting plate to door jamb using four (4) combo screws.
(Fig 1)
Install lock body and secure with four (4) installation screws. (Fig 2)
Install lock cover and screw. (Fig 3)
- Slide front of cover over body, hooking alignment tab onto body.
- Push back of cover over body to snap into place.
Prep Barn Door for Dust Proof Strike with Emergency Release
Close barn door; throw lock bolt to mark exact strike center position.
Ensure minimum of 1″ to edge of door.
(Fig 1)
Using strike center as guide, drill pilot hole through door from strike side
with 1/8″ bit. With pilot hole as guide, use 1″ hole saw to drill 1-1/4″ deep
hole. DO NOT DRILL THROUGH DOOR. (Fig 2)
Using pilot hole as a guide, use 1/4″ bit to drill a hole from outside through
to connect with strike bore. (Fig 3)
NOTE: Standard barn door to wall clearance is approximately 3/8″ to 1/2″.
Install additional spacer behind strike faceplate as needed if door to wall
clearance is over 1/2″. Additional spacers can support maximum clearance of
3/4″ between door and wall. (Fig 4)
The ASSA ABLOY Group is the global leader in access solutions. Every day we help people feel safe, secure and experience a more open world.
Install Dust Proof Strike with Emergency Release
Install 1″ dust proof strike with 1/4″ release screws on outside. (Fig 1)
Cut break-away screw to appropriate door thickness. DO NOT OVER TIGHTEN. (Fig
2)
Install break-away screw and tighten with Allen wrench. DO NOT OVER TIGHTEN.
Screw on decorative cap by hand. (Fig 3)
Use release key, provided with lock set, to push through center hole on
release to push lockbolt back and unlock door. (Fig 4)
| Door Thickness | Length without Spacer | Length with Spacer |
|---|---|---|
| 1-3/8″ | 11/16″ | 15/16″ |
| 1-3/4″ | 1-1/8″ | 1-5/16″ |
ASSA ABLOY Opening Solutions
Architectural Accessories Group
Memphis, TN 38141
Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All
rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories
and Door Controls Group, Inc. is prohibited.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>