NKC Deluxe 14 Inch Corner Cubby Kit Instruction Manual

: August 31, 2024
: NKC

Table of Contents

Deluxe 14 Inch Corner Cubby Kit
Specifications:
Product Usage Instructions:
Tools Required:
Kit Contents:
Step-by-Step Assembly:

Deluxe 14 Inch Corner Cubby Kit

“`html

Specifications:

Designed for clothes, linens, and pantry items
Can be used in conjunction with any Northern Kentucky Cedar,
LLC product
Components can be mixed and matched for customization
Materials: Aromatic Red Cedar

Product Usage Instructions:

Tools Required:

Safety Glasses
Tape Measure
Hammer
Stud Finder
Cup of Water Level
1/16 Drill Bit
1/8 Drill Bit
2 Square Bit

Kit Contents:

C1 – (x15) 2″ Screws
D1 – (x3) 3″ Screws (Kit may contain extra hardware)
E1 – (x15) Shelf Support Pegs
x2 Top Panels
x2 Bottom Panels (notched for baseboards)
x3 Pre-drilled Shelves
x3 Adjustable Shelves

Step-by-Step Assembly:

Step 1 – Bottom Shelf Placement:

The bottom panels have a notch cut out. Tops will not have a
notch.
Select one of the bottom 3 holes for shelf placement. Drill
holes completely through on both bottom panels.

Step 2 – (Optional) Cut Bottom Panels:

If the unit is going to be installed in a room shorter than 84
inches, measure walls to determine if the unit will fit. Cut the
bottom panels to an appropriate size if needed.
No cutting is required if the room is taller than 84
inches.

Step 3 – Assembling Cubby Unit (Part 1):

Follow the instructions provided in the manual for assembling
the cubby unit. Take care to assemble each unit one at a time and
ensure proper fastening to the wall using studs or drywall
anchors.

FAQ:

Q: Can I attach this unit to another existing unit?

A: Yes, each unit may be attached to another or cut down to fit
your needs. Plan ahead and ensure proper fitting before making any
cuts.

Q: What should I do if the scent of the Aromatic Red Cedar

wears off?

A: Lightly sand with a fine sandpaper to revitalize the
scent.

Q: What should I do if I need assistance during assembly?

A: It is recommended to seek help from others during
installation for faster and easier assembly.

“`

Deluxe Corner Cubby Assembly
1. Use caution when assembling this unit. Excessive weight will cause damage to the unit. Serious or fatal injuries may occur from the unit falling if not properly fastened to the wall.
2. Products that are instructed to be fastened to the wall must either be connected to a stud or by drywall anchors (not included).
3. Each unit may be attached to another or cut down to fit your needs. With that in mind; Plan ahead. Assemble each unit one at a time, and only cut down pieces when you are confident that they will fit together.
4. Determine if your unit will fit in the desired space. The only cuts you should make prior to assembly are on the panels of a cubby unit, so they will fit when standing up-right.
5. If you purchased a cubby add-on, please refer to the instructions included with that unit before assembling anything. Special steps must be completed prior to installing this unit.
6. This unit is installed faster and much easier with the help of others.
For Support: Call toll free 855.239.9498 or 606.742.2745 Email – sales@northernkycedar.com Once your unit is complete, we would love to see it! Send us pictures at our Email!

Thank You For Your Purchase
Because this system is based around the concept of individuality, this system can be used in conjunction with any Northern Kentucky Cedar, LLC product. The different ways are limited only by your imagination, and as such, not all components have to be used during installation.
To ensure a proper and easy installation, thoroughly read and follow this document. Basic carpentry skills will help.
This system is designed for clothes, linens, and pantry items. Placing excessively heavy items in your closet may lead to structural failure.
Knots, checking, and light cracks are typical characteristics of Aromatic Red Cedar and do not warrant a cause for exchange or refund.
If scent wears off, lightly sand with a fine sandpaper to revitalize scent.
If you purchased a cubby add-on please refer to the instructions included with that unit before assembling anything. Special steps must be completed prior to installing this unit.
Tools you will need

Safety Glasses

Tape Measure

Hammer
Pg.2

Stud Finder

Cup of Water Level

– 1/16″ Drill Bit – 1/8″ Drill Bit – #2 Square Bit

Your Kit Will Include

C1 – (x15) 2″ Screws D1 – (x3) 3″ Screws (Kit may contain extra hardware)

E1 – (x15) Shelf Support Pegs

x2 Top Panels

Shelves will be Ventilated or Solid

x2 Bottom Panels

depending on your order

(notched for baseboards)

x3 Pre-drilled Shelves

x3 Adjustable Shelves
Pg.3

Step 1 – Bottom Shelf Placement
1.The bottom panels have the notch cut out. Tops will not have a notch.
2. Select one of bottom 3 holes for shelf placement. Drill holes completely through on both bottom panels.

!
Try to be gentle with the Pre-Installed Dowels.

1/8″ Drill Bit
Step 2 – (Optional) Cut Bottom Panels
1. If the unit is going to be installed in a room that is shorter than 84″ you must cut the bottom panels. Measure walls to determine if the unit will fit. If not, cut to an appropriate size. No cutting is required if the room is taller than 84″.

Pg.4

Step 3 – Assembling Cubby Unit (Pt.1)
Attach each pre-drilled shelf following the numbers below.

C1
(x6) 2″ Screws

x3 Pre-Drilled Shelves

1 Top Panel 1 Bottom Panel

The panel side with the channels goes on the outside of the cubby.
2
C1

3
C1

3

C1

2

1

C1

1
C1

Once each shelf is attached use a damp cotton swab on the holes opposite the pre-glued dowels. Only using enough that the wood is wet, avoid free-standing water in the holes.
Pg.5

Step 4 – Assembling Cubby Unit (Pt. 2)
Once the panels are wet, Line-up holes and dowels then tap with wood block and hammer

Step 5 – Assembling Cubby Unit (Pt. 3)

C1
(x6) 2″ Screws

C1 1

C1 2

1 Top Panel
1 Bottom Panel

C1 4

Repeat Steps 3 & 4 to attach the last top panel
Attach Panel
3

Pg.6

1. Connect Poles (with the water method) Align holes to one side

Step 6 – Attach Corner Pole
2. Attach Pole to cubby using 2″ screws (C1). The holes on the Pole should match that of the panel.
C1

3. Adjust the pole size by cutting it to match your baseboards (if needed)