DMOS 2024 Delta and Delta Pro Shovel Instructions
- August 28, 2024
- DMOS
Table of Contents
DMOS 2024 Delta and Delta Pro Shovel
Specifications:
- Product Name: T-GRIP Shovel
- Shaft: 3-piece design with pushpins
- Blade: Adjustable between Shovel, Hoe, and Stow modes
- Handle: T-Grip design for ergonomic use
- Patent: dmosproshoveltools.com
Product Usage Instructions
Assembling and Adjusting the Shovel:
- A. Depress pushpin A and insert handle (T-Grip and 3-piece shaft) into neck connector until pushpins engage holes.
- B. Pull the detent pin out of the connector hole by holding the ring and adjust the blade to the desired mode.
- C. Insert the detent pin into the corresponding connector hole based on the mode chosen.
Extending the Handle:
- A. Depress the pushpin closest to the T-Grip while pulling the shaft away to extend it until it catches the next set of pushpins.
- B. Repeat the process, starting at the pushpin closest to theT-Grip, until you reach the desired handle length.
Collapsing and Storing the Shovel:
- A. Collapse the shaft by depressing the 2nd pushpin from T-Grip and then engage shaft holes until pushpins lock into place.
- B. Engage stow mode for storage by removing the detent pin, positioning in stow mode, and inserting the detent pin into the stow mode connector hole.
- C. Stow the shovel in a Delta Mount or Delta Shovel Bag (Sold Separately).
- D. After use, check and clear any debris from detent pins and connector holes. Periodically oil the ball in the detent pin for smooth operation.
PRODUCT OVERVIEW
DEPLOYING YOUR SHOVEL
Assemble shovel and adjust the blade mode
-
A. Depress pushpin A and insert handle (T-Grip and 3-piece shaft) into neck connector until pushpins engage holes.
-
B. With your finger in the ring of the detent pin, pull pin out of the connector hole.
Note: you may need to lift and wiggle the shaft to take tension off the pin. -
C. Adjust the blade to desired mode.
-
D. Insert the detent pin into the corresponding connector hole.
Extending the handle
- A. Depress the pushpin closest to the T-Grip while pulling shaft away from grip to extend shaft segment. Do this until segment catches next set of pushpins.
- B. Repeat process, always starting at the pushpin closest to T-Grip,until you get to your desired handle length.
Note: If for any reason you take all the segments apart, don’t worry. Just put them back in order and clip them back into place by depressing the pushpins.
COLLAPSING YOUR SHOVEL
Collapse the shaft to its fully nested position.
- A. Depress 2nd pushpin from T-Grip and collapse shaft.
- B. Depress 1st pushpin from T-Grip and engage shaft holes until pushpins lock into place.
- C. Repeat until fully collapsed.
Engage stow mode for storage.
- A. Remove detent pin from the shovel or hoe mode connector hole.
- B. Position shovel in stow mode.
- C. Insert detent pin in stow mode connector hole.
- D. Stow shovel in Delta Mount or Delta Shovel Bag (Sold Separately).
Note: After use, check the detent pin and connector holes for debris. Clear the debris with a cloth. You will need to periodically oil the ball in the detent pin to ensure ease of operation so that debris won’t impede its movement.
FAQ:
Q: How do I adjust the blade mode on the shovel?
A: To adjust the blade mode, follow step 1 in the deploying section
where you need to depress pushpin A, insert the handle into the neck
connector, adjust the blade to your desired mode, and insert the detent pin
into the corresponding connector hole.
Q: What should I do if all segments of the handle are taken apart?
A: Don’t worry if all segments are apart. Just put them back in order
and clip them back into place by depressing the pushpins following step 2 in
extending the handle section.
Q: How should I store the shovel after use?
A: Follow step 2 in collapsing your shovel section to engage stow mode
for storage. Remove the detent pin,position in stow mode, insert detent pin
into stow mode connector hole, and then stow it in a Delta Mount or Delta
Shovel Bag.
LOVE YOUR DMOS® PRODUCT? DON’T KEEP IT A SECRET – LEAVE A REVIEW!