CONCEPTRONIC ZEUS51E1K UPS Double Conversion Installation Guide
- August 28, 2024
- CONCEPTRONIC
Table of Contents
ZEUS51E
Quick Installation Guide
ZEUS51E1K UPS Double Conversion
This Quick Installation Guide provides essential information for basic setup.
For detailed instructions and additional features, please refer to the
comprehensive user manual available for download on the Conceptronic website:
www.conceptronic.net.
Please read and follow all instructions carefully during installation and
operation of the unit. Read this manual thoroughly before attempting to
unpack, install, or operate the UPS.
CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or
circuit breaker protection. DO NOT plug the UPS into an outlet that is not
grounded. If you need to power-drain this equipment, turn off and unplug the
unit.
CAUTION! The battery can power hazardous components inside the unit, even when
the AC input power is disconnected.
CAUTION! The UPS should be placed near the connected equipment and easily
accessible.
CAUTION! To prevent the risk of fire or electric shock, install in a
temperature and humidity controlled indoor area, free of conductive
contaminants. (Please see specifications for acceptable temperature and
humidity range).
CAUTION! (No User Serviceable Parts): Risk of electric shock, do not remove
cover. No user serviceable parts inside. Refer servicing to qualified service
personnel.
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock, battery
circuit is not isolated from AC power source; hazardous voltage may exist
between battery terminals and ground. Test before touching.
CAUTION! To reduce the risk of fire, connect the UPS to a branch circuit with
10 amperes (1K / 2K) / 16 amperes (3K) maximum over-current protection in
accordance to CE requirement.
CAUTION! The AC outlet where the UPS is connected should be close to the unit
and easily accessible.
CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g. the mains
cable of your equipment), to connect the UPS to the AC outlet.
CAUTION! Please use only VDE-tested, CE-marked power cables to connect any
equipment to the UPS.
CAUTION! When installing the equipment, ensure that the sum of the leakage
current of the UPS and the connected equipment does not exceed 3.5mA.
CAUTION! Do not unplug the unit from AC Power during operation, as this will
invalidate the protective ground insulation.
CAUTION! To avoid electric shock, turn off and unplug the unit before
installing the input/output power cord with a ground wire. Connect the ground
wire prior to connecting the line wires!
CAUTION! Do not use an improper size power cord as it may cause damage to your
equipment and cause fire hazards.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT!
Under no circumstances this unit should be used for medical applications
involving life support equipment and/or patient care.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not
use with or near aquariums. Condensation from the aquarium can come in contact
with metal electrical contacts and cause the machine to short out.
CAUTION! Do not dispose of batteries in fire as the battery may explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is harmful
to the skin and eyes.
CAUTION! A battery can present a risk of electric shock and high short circuit
current. The following precaution should be observed when working on batteries
- Remove watches, rings or other metal objects.
- Use tools with insulated handles.
CAUTION! The unit has a dangerous amount of voltage. When the UPS indicators
is on, the units may continue to supply power thus the unit’s outlets may have
a dangerous amount of voltage even when it’s not plugged in to the wall
outlet.
CAUTION! Make sure everything is turned off and disconnected completely before
conducting any maintenance, repairs or shipment.
CAUTION! Connect the Protection Earth (PE) safety conductor before any other
cables are connected.
WARNING! (Fuses): To reduce the risk of fire, replace only with the same type
and rating of fuse.
DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR NEAR A
STRONG HEAT SOURCE!
DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE HOUSING! DO NOT CONNECT
DOMESTIC APPLIANCES SUCH AS HAIR DRYERS TO UPS OUTPUT SOCKETS!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR SUPERVISED BY PERSONNEL
KNOWLEDGE OF BATTERIES AND THE REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED
PERSONNEL AWAY FROM BATTERIES!
Disposal of waste electrical equipment and batteries: Do not dispose of waste
electrical equipment and batteries with household waste. Please hand them to
your local recycling point. Batteries should be fully discharged when disposed
of. Incorrect storage/disposal can harm the environment and/or cause injury.
CE marking: Conceptronic declares that this product complies with the
directives listed in the section ‘Declaration of Conformity’.
UNPACKING
(1) UPSx1; (2) Quick installation guide x1; (3) Input power cord (EU/UK) x2;
(4) Rackmount ears (Stands) x2; (5) Flat head screws: M4x8Lx8; (6) Screw hole
dust covers x8; (7) Pan head screws:M5x12Lx4; (8) Plastic washers x8; (9) USB
cable x1; (10) RS232 cable x1
-
Power On/Off Button
Master ON/OFF for the UPS. -
Function Buttons
Scroll up, scroll down, select and cancel LCD menu. -
Multifunction LCD Readout
Indicate status information, settings and events. -
AC Input Inlet
Connect the AC Power cord to a properly wired and grounded outlet. -
Input Circuit Breaker
Provide input overload and fault protection. -
EPO (Emergency Power Off) Connector
Enable Power-Off in emergency from a remote location. -
USB port
This is a connectivity port which allows communication and control between the UPS and the connected computer. It is recommended to install the Power master software on the PC/Server connected with the USB cord. -
Serial Port
Serial port provides communication between the UPS and the computer. The UPS can control the computer’s shutdown during a power outage through the connection while the computer can monitor the UPS and alter its various programmable arameters. -
SNMP/HTTP Network slot
Slot to install the optional SNMP card for remote network control and monitoring. -
Battery Backup & Surge Protected Outlets
Provide battery backup and surge protection. They ensure power is provided to connected equipment over a period of time during a power failure. -
Extended Runtime Battery Module Connector Connect to additional external battery modules.
HARDWARE INSTALLATION
These versatile UPS systems can be mounted in a rackmount or vertical tower
orientation. This versatility is especially important to growing organizations
with changing needs that value having the option to position a UPS on a floor
or in a rackmount system. Please follow the instructions below for the
respective mounting methods.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only use the supplied
hardware to attach the mounting brackets.
RACKMOUNT INSTALLATION
Step 1: Rackmount ears installation
Attach the two rackmount ears to the UPS using the provided screws M4X8L*8pcs.
Step 2: Rackmount rails Installation(optional)
- The rails adjust to mount in 48-cm (19-inch) panel racks from 52 to 91.5cm (20.5 to 36 inches) deep. Select the proper holes in the rack for positioning the UPS in the rack. The UPS takes up position 1 through position 6.
- Attach the rackmount rail to your rack with two M5X12L screws and two plastic washers at the front of the rack. (Located in position 1 & position 6) Do not tighten the screws. Adjust the rail size on the rail assembly of your rack. Secure the rail to the rear of the rack with two M5X12L screws and two plastic washers. Tighten all screws at the front and rear of the rail. Once completed, perform the same steps for assembling the other rackmount trail.
Step 3: Install the UPS on the rack (optional)
Place the UPS on a flat stable surface with the front of the unit facing toward you.
Secure the UPS to your rack with four M5X12L screws at the front of the rack. (Located in position 2 & position 5).
VERTICAL/TOWER INSTALLATION
Step 1: Attach the base stands
Tighten the screws (M4X8L*8pcs) of the base stands (rackmount ears) onto the
bottom of the UPS. Step 2: Attach dust covers
Insert dust cover into the rackmount ear screw holes that are not being used.
SOFTWARE INSTALLATION
Power Master+ management software provides a user-friendly interface for your
power systems. The graphic user-interface is intuitive and displays essential
power information at a glance. Please follow procedure below to install the
software.
Installation procedure:
- Download Power Master+ from the website: https://www.powermonitor.software/
- Double-click the file and follow the installation steps. When your computer restarts, the Power Master+ software will appear as a blue icon located in the system tray.
Need Help?
support@conceptronic.net
www.conceptronic.net
Digital Data Communications GmbH – Im Defdahl 10 F, 44141 Dortmund, Germany
CONCEPTRONIC® is a registered trademark of Digital Data Communications GmbH
© Copyright Digital Data Communications GmbH. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>