SKYZONE Steadyview X FPV Goggles Screen Receiver User Manual
- August 25, 2024
- SkyZone
Table of Contents
5G
Steady View X
USER MANUAL
V1.1 20240607
Specification
Display|
---|---
Screen| 0.96″ Color LCD
Viewing direction| ALL View
Receiver|
Frequency| 4.9-6GHz, 7Band x8Channels
Sensitivity| -98dBm±1dBm
Narrow-Band Filter| Yes
Antenna Connectors| 2x Standard SMA-K,50ohm
Mode| Mix1,Mix2,Mix3, Diversity, Single RX
Video output| 1.0Vp-p Typ. / 75ohm
Audio output| No audio output
Power|
Voltage| 6.5-26V
Consumptio| 12V input@240mA Normal, 180mA Single RX
Interface|
DC IN| ΦD5.5mm@PIN2.1mm
A/V output| Φ3.5mm
USB| Type-C, Firmware Update
Dimensions| 65(L)X32(W)X32(H)
Weight| 49g
BAND/CH Table
BAND/CH table
BAND/CH| CH 1| CH 2| CH 3| CH 4| CH 5| CH 6| CH 7| CH 8
A| 5865M| 5845M| 5825M| 5805M| 5785M| 5765M| 5745M| 5725M
B| 5733M| 5752M| 5771M| 5790M| 5809M| 5828M| 5847M| 5866M
E| 5705M| 5685M| 5665M| 5645M| 5885M| 5905M| 5925M| 5945M
F| 5740M| 5760M| 5780M| 5800M| 5820M| 5840M| 5860M| 5880M
R| 5658M| 5695M| 5732M| 5769M| 5806M| 5843M| 5880M| 5917M
L| 5362M| 5399M| 5436M| 5473M| 5510M| 5547M| 5584M| 5621M
X| 4990M| 5020M| 5050M| 5080M| 5110M| 5140M| 5170M| 5200M
Sensitivity| -98dBm±2dBm
Antenna| 2 X SMA-K,50ohm
Package include
- SteadyView X Receiver*1
- Patch Antenna 5.0G *1
- Omni Antenna 4.9G *1
- SKYZONE SKY04X Module Cover*1
- FATSHARK Module Cover*1
- XT60-DC Cable 5.52.1 1
- 3.5mm Video Cable*1 1.2m
- USB-C Cable*1
- User Manual*1
IO Port
3.5mm Video port Pin out
Introduction
Steadyview X receiver is high performance receiver, unlike traditional diversity receiver, the Steadyview X have unique fusion technology and low band Filter hardware, also unique image reconstruction algorithm, the receiver merge two signals to one, avoid image tearing and rolling, make image more stable and clear in challenging condition. The receiver come with ground station kit and 3 module bay cover, use can use the receiver on SKYZONE 04 series or fatshark goggles, also on SKYZONE Cobra goggles, user can use the receiver on any goggles or monitors which have AV INPUT port.
Quick Start
BAND/CH setting
- In preview mode, press the wheel to enable OH setting, roll the wheel to change Channel, press the wheel again to enable BAND setting, roll the wheel the change the BAND.
- No movement for 3 seconds, the receiver will back to preview mode.
- The front with switch from big front and small front in preview mode.
Auto Search
- Hold the wheel to pop out search menu, press the wheel to enable search, the receiver will start search, after search, the receiver will change to strongest RSSI CH.
- After search, the screen will show all rssi bar, use can roll the wheel to manually adjust the CH.
- Press the wheel during the search to quit search.
Sometime the auto search is not accurate, user need manually adjust the CH.
Receiver Mode
Some camera on market didn’t follow standard NTSC/PAI signal, cause the receiver confusing inM ix mode, It will cause image getting dark, color distortion, rolling image, user can switch to diversitymode to solve this issue. user can use these mode to get solve these issue.
2. Mix1 :this is basic mix mode, this mode provides basic fusion processing
to reduce excessive interference of the circuit on the image.
3. Mix2 : this mode i improves synchronization stability, especially in weak
signals to maximize synchronization and lock video. 4. Mix3: Enhance the
synchronization signal on the basis of Mix2, maximize the stability of the
video and maximize the compatibility with camera. In this mode, The brightness
of the signal will be reduced
5. Mix Off: the receiver will turn off the MIX feature, the receiver will
work in traditional diversity mode receiver or signal. receiver mode.
Antenna Select
In this menu, user can choose Diversity, A, B.
Diversity; in this mode, the two receiver will work same time, will choose the
strongest signal to output.
A,B: this mode, there is only one receiver is working to save the power.
Stabilize Time
The parameter is only valid in the MIX mode. You can set the stable time after
the receiver loses the synchronization signal. The default is 8 seconds. Mix1
is recommended to be set to 5 seconds or 8 seconds.
The longer the setting, the longer the stabilization time, but Since the sync
signal has been lost black bars may appear on the left or right side of the
video, This is because the synchronization signal generated by the receiver
and the VTX transmission the video synchronization signal sent is not
synchronized, and the error is getting bigger and bigger. Once the signal is
restored to sufficient strength, it will be synchronized immediately. If the
time is stilt not synchronized, the receiver signal loses lock and
automatically works in diversity or single receiving mode.
OSD Mode
USER can choose the OSD style in the Video. the OSD is on the top left of the
image.
LocklconFreq : Lock Statues, formation of signal, RSSI bar, frequency.
Locklcon : Lock Statues, formation of signal, R551 bar.
LockFreq : Lock Statues, formation of signal, frequency.
Lock: Lock statues and Formation of Video Signal
OFF: OSD Turn off the OSD in the video.
MENU Style
User can change the menu style in this mode,
Style1 : White on a blue background
Style2: Blue on a yellow background
Style3: White on a black background
Calibration
- Calibrating the RSSI helps the receiver to work better and show the RSSI strength more accurately
- The calibration consists of two steps, both of which must be executed correctly to complete the calibration.
- to calibrate the low rssi: make sure the receiver and VTX are working normal and matched , turn off the VTX power, calibrate the low rssi in the menu, when is done, turn on the power of VTX, then calibrate the high R551 of receiver, when its done, user can quit the calibration menu.
ELRS
The Steadyview x have ELRS VRX backpack build in, user can synchronize the VRX and VTX with TX backpack.
- under ELRS menu, user can choose turn on or turn off the ELRS backpack.
- If ELRS is turn on, user need go to bind mode under ELRS menu to bind the backpack to TX backpack. need Lua Script to bind the backpack, screen will show binding success after binding is done.
- Upgrade the firmware, user can upgrade the VRX backpack firmware with ELRS configrator, plug the receiver to PC, and select upgrade under ELRS menu, then the ELRS will go to boot mode, go to ELRS configrator choose backpack, select the VRX backpack, target is Steadyview+ELRS, then choose the correct com port and start build and flash, also user can add binding phrase if the TX backpack already have binding phrase.
Update Firmware
- Hold the wheel when connect the receiver to the computer.
- Computer will automatically install the driver , computer will show a new removable storage .
- Copy the steadyview x Firmware File to the folder, receiver will installing the update at the same time. when the copying is done, the firmware update is done.
Download latest menu atwww.skyzonefpv.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>