EVERSTONE S26S Globe Wall Mount Installation Guide

: August 25, 2024
: EVERSTONE

Table of Contents

EVERSTONE S26S Globe Wall Mount
Product Information
Product Usage Instructions
STONE SERIES INSTALLATION GUIDE
HARDWARE
INSTALLATION
BALLAST AND LAMP REPLACEMENT INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EVERSTONE S26S Globe Wall Mount

Product Information

Specifications :

Models: S26S, S26V, S27S, S27V
Power Supply: 120V
Maximum Lamp Wattage: 26W
Lamp Type: SBCFL(GU-24)
Photo Sensor: Integral, non-adjustable
Grounding: Green or Bare

Product Usage Instructions

Before Installation:

Check for any shipping damages and ensure all hardware is received.

Installation Steps:

Disconnect main power supply at the breaker box.
Do not turn off power at the wall switch only.
Install integrated lamp/ballast (SBCFL) specified on the fixture.
Apply silicone caulk around the fixture backplate for a watertight seal.
Turn on the main power.

Important Notes:

Model S26S must be installed in an UPLIGHT position.
Model S26V must be installed in a DOWNLIGHT position.
The fixture may have an integral photo sensor that controls day/night operation.

Ballast and Lamp Replacement:
To replace the lamp/ballast, grasp the plastic area on each side of the bulb area and rotate counterclockwise. Replace with MAX 26W SBCFL(GU-24) marked with UL and C, US Logo. Do not use where directly exposed to water or in totally enclosed luminaires.

FAQ :

Q: What should I do if my fixture is missing parts or damaged?
A: Do not return to the retailer. Call for direct assistance at 1-877-870-9283.
Q: Can the photo sensor be adjusted?
A: The photo sensor is not adjustable. Cycling may occur if light reflects into the sensor from nearby surfaces. To address cycling, remove the sensor nut and install the swivel hood and base.
Q: How do I dispose of the lamp if it contains Mercury?
A: Follow disposal laws. Visit www.lamprecycle.org for more information.

STONE SERIES INSTALLATION GUIDE

MODELS : S26S, S26V, S27S, S27V

If for some reason you are missing parts of have a problem with your ﬁxture
DO NOT CALL OR RETURN TO THE RETAILER. Call for direct assistance at 1-877-870-9283.
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING FIXTURES.

BEFORE INSTALLATION

Please check to see that your ﬁxture was not damaged during shipment, and that you received all the hardware needed for installation. While we strive for perfection, accidents do happen. If you have a problem or are missing any parts, please call us at 1-877-870-9283 immediately.
CAUTION: Disconnect main power at the breaker box before beginning installation. Do not turn power off at the wall switch only. Failure to properly disconnect the main power supply may result in serious injury.
CAUTION: Install the appropriate size lamp in your Stone ﬁxture. Do not exceed the manufacturer’s maximum wattage restrictions.
SPECIAL NOTE: For easier installation, it is recommended the two (2) people be used when making the electrical connections and mounting the ﬁxture.

HARDWARE

INSTALLATION

Disconnect main power supply at the breaker box. DO NOT turn power off at the wall switch only.
CAUTION : FAILURE TO DISCONNECT MAIN ELECTRICAL POWER MAY RESULT IN SERIOUS INJURY.
GU24 FLUORESCENT
Install integrated lamp/ballast (SBCFL). Use SBCFL speciﬁed on ﬁxture. Grasp the plastic base, insert pins into socket and rotate clockwise until secure.
Apply silicone caulk completely around the ﬁxture backplate for a watertight seal.
CAUTION : Model S26S wall mounts must be installed in an UPLIGHT position only. Model S26V inverted wall mounts must be installed in a DOWNLIGHT position only.

Customer Service 1-877-870-9283 www.wavelighting.com

This ﬁxture may have an integral photo sensor that turns the ﬁxture off during the day and on at night. The photo sensor is not adjustable. The ﬁxture could possibly cycle on and off due to light reﬂected from nearby surfaces into the photo sensor. If cycling occurs, remove the photo sensor nut and install the swivel hood and base.
The hood and base are adjustable. The hood can be rotated and the base can be cut along the dotted line to reduce overall length. Check operation before cutting the base.

BALLAST AND LAMP REPLACEMENT INSTRUCTIONS

Product contains an integrated Lamp/Ballast combination. To remove, grasp plastic area on each side of bulb area and rotate counterclockwise. Replace with MAX 26W SBCFL(GU-24) that is marked with the UL and C, US Logo. Use SBCFL marked – Not for use where directly exposed to water. Do not use SBCFL marked – Not for use in totally enclosed luminaire.
Mark means lamp contains Mercury. Follow disposal laws. See www.lamprecycle.org
1102453-GUES Rev. B