BOSCH SMS6ECC00E Freestanding Dishwasher 60cm Stainless Steel User Guide
- August 24, 2024
- Bosch
Table of Contents
- BOSCH SMS6ECC00E Freestanding Dishwasher 60cm Stainless Steel
- Specifications
- Setting up Home Connect
- Overview of water hardness settings
- Adding special salt
- Cleaning filters
- Cleaning spray arms
- Programmes
- Troubleshooting
- Frequently Asked Questions
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BOSCH SMS6ECC00E Freestanding Dishwasher 60cm Stainless Steel
Specifications
- Model: Dishwasher
- Water Hardness Settings: Soft (0 – 1.1 mmol/l), Medium (1.5 – 5.4 mmol/l), Hard (5.5 – 8.9 mmol/l)
- Programs: Various programs with different durations, energy consumption, and water usage
Before using for the first time, read the instruction manual and the safety information it contains.
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can con-veniently change all settings using the Home Connect app.
- Install the Home Connect app on your mobile device and fol-low the instructions.
- Scan the QR code with the Home Connect app.
Overview of water hardness settings
- You can find an overview of the water hardness values that can be selected here.
- A table of country-specific units can be found in the instruction manual.
Setting the water softening sys-tem
- Press .
- To open the basic settings, press Setup 3 sec for 3 seconds.
- The display shows H:xx.
- The display shows .
- Press – or + repeatedly until the right water hardness has been set.
- To save the settings, press Setup 3 sec. for 3 seconds.
Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the program starts.
- Unscrew the lid of the dispenser for special salt and remove it.
- On initial start-up: Fill the dispenser right up with water.
- Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
- Place the lid back on the dispenser and turn to close.
Adding rinse aid
- Press the catch on the lid of the dispenser for rinse aid 1 and 2 lift .
- Add rinse aid up to the max mark.
- Close the lid of the dispenser for rinse aid.
- The lid clicks into position.
Adding detergent
- Add the detergent to the dry detergent dispenser
- Close the lid of the detergent dispenser.
- The lid clicks into position
How to use your appliance
-
Load the tableware.
Only clean tableware that is suitable for dishwashers.
Remove large remnants of food from the tableware. Check that the spray arms can rotate freely. -
Add detergent.
-
Switch on the appliance .
-
Select the program.
-
Start the program Start .
-
Remove the tableware at the end of the programme.
-
To cancel the programme, press Reset 4 sec for approx. 4 seconds
The programme is canceled and ends after approx. 1 minute.
Cleaning filters
- After each wash check the filters for residue.
- Turn the coarse filter anticlock- wise 1 and remove the filter system 2.
- Pull down the microfilter to remove.
- Press the locking catches 1 together and lift the coarse filter out 2.
- Clean the filter elements under running water.
- Re-assemble the filter system.
- Insert the filter system into the appliance and turn the coarse filter clockwise.
Make sure that the arrow markings match up.
Cleaning spray arms
- Unscrew the upper spray arm 1 and pull down to remove 2.
- Pull up the lower spray arm to remove.
- Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
- Insert the lower spray arm.
- The spray arm clicks into position.
- Insert the upper spray arm and screw it firmly in place.
Clean wastewater pump
- Disconnect the appliance from the power supply.
- Remove the filter system.
- Scoop out any water.
- Prise off the pump cover using a spoon and grip it by the crosspiece.
- Lift the pump cover inwards at an angle and remove.
- Remove any remnants of food and foreign bodies in the area of the impeller.
- Insert the pump cover 1 and press down 2.
- The pump cover clicks into position.
- Install the filter system
Programmes
The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added.
- Suitable programme for running at night: it takes longer, but is extremely quiet.
- half standard load
Troubleshooting
The filters in the water connection of the supply or AquaStop hose are blocked
- Switch off the appliance.
- Pull out the mains plug.
- Turn off the water tap.
- Unscrew the water connection.
- Remove the filter from the supply hose
- Clean the filter.
- Re-insert the filter in the supply hose.
- Screw the water connection back on.
- Check the water connection for leaks.
- Restore the power supply.
- Switch the appliance on.
Frequently Asked Questions
- Q: How often should I add rinse aid?
- A: Add rinse aid whenever the level is low or as indicated by the appliance for optimal performance.
- Q: Can I use regular salt instead of special salt?
- A: No, only use special salt designed for dishwashers to prevent damage to the appliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>