NRT-AA-B Nano-RT Asset Tag User Manual

NRT-AA-B Nano-RT Asset Tag

Specifications

• Features: 2.4 GHz radio, CR2032 battery, (2) LEDs, Double-sided adhesive attachment, Temperature sensor
• Exterior Dimensions: 23.3 mm x 8.6 mm
• Operating Temperature: Not specified
• Storage Temperature: Not specified

Product Usage Instructions

Safety Recommendations

• This product is for commercial use only. Avoid installation in areas where children are present to prevent accidents.
• Follow safety instructions to avoid fire, electric shock, or injury.

Battery Usage

• Only use UL-approved CR2032 batteries with this product to prevent hazards. Improper battery usage can result in fire or electric shock.
• Dispose of batteries according to laws and regulations.

Warnings

• Avoid ingesting the battery as it can cause severe internal burns and even death. Keep batteries away from children and seek medical attention if ingestion is suspected. Stop using the product if the battery compartment does not close securely.
• The asset tag is a proximity tag designed for commercial use with various mounting options. It features a 2.4 GHz radio, CR2032 battery, LEDs, double-sided adhesive attachment, and a temperature sensor. The exterior dimensions are 23.3 mm x 8.6 mm.

Installing the Tag

1. Clean the asset surface with a 50/50 mixture of isopropyl alcohol and water to remove dust and oils.
2. Attach the tag using the provided 3M adhesive:
3. Remove one side of the protective film and attach it to the blank side of the tag without obscuring the QR code.
4. Remove the other side of the protective film and firmly apply it to the asset.
5. Activate the tag by pulling the battery tab.
6. Use asset tracking software to pair the tag:
7. Scan the tag’s QR code or manually enter the tag ID.
8. Enter asset information.
9. Confirm successful pairing by pressing SUBMIT.

LED Blink Rate: Fast Blink (0.1 seconds each), Slow Blink (1.0 seconds each)

FAQ

• Q: Can I use any type of battery with this product?
• A: No, only UL-approved CR2032 batteries should be used to avoid potential hazards.
• Q: What should I do if the battery compartment does not close securely?
• A: Stop using the product and keep it away from children. Seek immediate medical attention if ingestion is suspected.

Safety Recommendations

• This is a commercial use product and should not be installed where children will be present.
• Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage.
• Do not disassemble, dismantle, open, crush puncture, or shred the product.
• If the product housing/envelope is weakened, cracked, or broken, stop using it immediately.
• Do not attempt to short-circuit the battery or make contact with a conductive/metal object.
• Do not expose the product to heat, fire, or flame.
• Do not fully immerse the product in water or other liquid.
• The battery should be replaced by a trained professional using appropriate tools. The a danger of explosion if the battery is incorrectly replaced.
• ONLY UL-approved CR2032 batteries can be used in this product. Any other battery could result in fire, electric shock, or damage.
• Dispose of all batteries under application laws and regulations.

WARNING
Do not ingest the battery. Chemical Burn Hazard.
This product contains a coin cell battery. If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think a battery might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Failure to follow these instructions can result in personal injury or property damage, and the manufacturer will have no liability whatsoever for any such injury or damage arising from or in connection with any failure to follow these or other instructions provided to the end user.

Description

The asset tag is a long-life, cost-effective proximity tag with multiple mounting options designed for commercial environments. The asset tag is intended to be attached to an asset by the methods outlined in this user manual only.
Asset Tag Features and Sensors:

• 2.4 GHz radio
• CR2032 battery
• (2) LEDs
• Double-sided adhesive attachment.
• Temperature sensor

The product has the following exterior dimensions: 23.3 mm x 8.6 mm

Characteristics

Listed below are the main performance characteristics:

1 The indicated storage temperature range is intended to maximize the battery life and avoid unexpected discharge during storage. The product can be exposed to an increased temperature range than the indicated storage temperature range (as long as it stays within the operating temperature range), but exposure to more extreme temperatures during storage may reduce battery life.

Installing the Tag

• The product is designed to have a small footprint and be attached to commercial equipment using the provided 3M adhesive.

Adhesive
Before adhering the device to the asset surface, clean it using a 50/50 mixture of isopropyl alcohol and water can remove dust and oils on the surface to prep for good adhesion.
The ideal application temperature range for adhesive application is 70°F to 100°F (21°C to 38°C) but as low as 32°F (0°C) is acceptable. The adhesive will bond to a broad range of high surface energy substrates including metals, glass, plastics and easier to bond paints.

1. Using the included Tag double-sided adhesive, remove one side of the protective film and secure it to the blank side of the Tag a.Avoid obscuring Tag QR code
2. Remove the other of side of the protective film and apply it securely to the asset

Activation

1. Pull the battery tab to turn on the Tag
2. Using asset tracking software,
   • Scan the Tag QR code or manually enter the Tag ID benter asset information
   • Confirm successful pairing by pressing SUBMIT

Button & LED Behavior
LED Blink Rate:

LED Actions

Regulatory Notices
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation of this device is restricted to indoor use only.

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body: Use only the supplied antenna.

ISED Notice of Compliance
CAN ICES-3(B) / NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>