Rowenta DW958X Steam Force Pro Steam Iron Instruction Manual

: August 23, 2024
: Rowenta

Table of Contents

Rowenta DW958X Steam Force Pro Steam Iron
FAQs
IMPORTANT SAFETY INSTRUCTIONS
SPECIAL INSTRUCTIONS
DESCRIPTION
BEFORE USE
CONTACT INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Rowenta DW958X Steam Force Pro Steam Iron

FAQs

Q: What should I do if I notice fumes and odor during the first few uses?
- A: This is normal and harmless. It will disappear quickly and does not affect the iron’s performance.
Q: How do I activate the shot of steam for tough creases?
- A: On linen and cotton mode, press the trigger for 1 second max and release. Wait a few seconds between each shot.
Q: Can I use the iron for dry ironing?
- A: Yes, select Synthetic mode for dry ironing. It is ideal for delicate or perfect finishing.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using the iron. When using your iron, basic safety precautions should always be followed, including the following:

Use iron only for its intended use.
To protect against the risk of electric shock, do not immerse the iron in water or other liquids.
Always turn the iron OFF before plugging or unplugging the iron from the electrical outlet. Never pull on the cord to disconnect the iron from the electrical outlet; instead, grasp the plug and pull on the plug to disconnect the iron.
Do not allow the cord to touch hot surfaces. Let the iron cool completely before putting it away. Loop cord loosely around iron when storing.
Always disconnect the iron from the electrical outlet when filling with water or emptying and when not in use.
Do not operate the iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Contact our Consumer Service Department for examination, repair, or adjustment. Incorrect reassembly can cause a risk of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by or near children. Do not leave the iron unattended while connected or on an ironing board.
Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
This appliance is only for domestic and personal use.

SPECIAL INSTRUCTIONS

To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.
If an extension cord is necessary, a 15 amp. cord should be used. Cords rated for less amper may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS EN For your safety

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE.
This appliance complies with the technical rules and standards for safety currently in force (Electromagnetic Compatibility, Low Voltage, Environnement).
This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children must be supervised to ensure that they do not play with the appliance.
During the first few uses, you may notice some fumes, a harmless odor, and a slight release of particles. This phenomenon, which does not affect use, will quickly disappear.
Warning! The voltage of your electrical installation must correspond to that of the iron (120V or 127 V). Connecting to the wrong voltage may cause irreversible damage to the iron and will terminate the guarantee.
If it is essential to use an extension cable, choose a 15 amp cord.
If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger.
The appliance should not be used if it has fallen if it has obvious damage if it leaks or functions incorrectly.
Never dismantle your appliance: have it inspected by an Approved Service Centre, to avoid any danger.
Never immerse your iron in water!
Do not unplug your appliance by pulling on the cord.
Always unplug your appliance: before filling or rinsing the water tank, before cleaning it, and after each use.
Never leave the appliance unattended when it is connected to a power source or if it has not cooled down for approximately 1 hour.
Your appliance gives off steam, which may cause burns.
Take extra care especially when you are ironing close to the edge or on a corner of your ironing board. Never direct the steam towards people or animals.
Your iron should be used and placed on a flat, stable, heat-resistant surface. When you put your iron onto its iron rest, make sure that the surface on which you put it is stable.
This product has been designed for domestic and indoor use only. The manufacturer will accept no responsibility and the guarantee will be terminated, if this product is used for commercial purposes, inappropriate use, or failure to comply with the instructions.

WHAT WATER TO USE?

Your appliance was designed to operate using tap water.
However, it is necessary to periodically clean the steam chamber to remove any mineral deposits.
If your water is very hard (above 30°f or 17°dH or 21°e), mix 50% tap water with 50% demineralized water (available in hardware stores).
Do not use water with additives (starch, perfume, aromatic substances, softener, etc.), condensation water (e.g. water from clothes dryers, water from refrigerators, water from air conditioners, rainwater), pure demineralized or pure demineralized water.
These types of water contain organic waste, and mineral elements that become concentrated when heated and cause spitting, brown staining, leaking, or premature wear on your iron.

ENVIRONMENT Environment protection first!

Your appliance contains valuable materials that can be recovered or recycled. Leave it at a local civic waste collection point.

DESCRIPTION

Smart Led Screen with electronic temperature control
Mode button
Steam Shot trigger
Cord
Handle
Water tank
High precision tip
Soleplate
Filling inlet
Rear cover

BEFORE USE

Please read carefully the “Safety and use instructions” booklet before first use.
IMPORTANT Remove the protective sticker from the soleplate.

USE

Filling the water tank
- Before filling the water tank, unplug the iron Fig 1.
- Open the water filling inlet Fig 2. Fill in water up to the Max. mark. fig 3. Close the filling inlet and return the iron to the horizontal position.
- You can plug in your iron Fig 4.
Setting the temperature
- Your iron is equipped with the Autosteam Electronic Control function, which automatically adjusts the steam amount and the temperature based on the selected fabric for optimum results.
- Select the fabric to be ironed by pressing the MODE button to select the appropriate fabric. fig 5. For perfect results, an optimum position for each fabric has been pre-defined.
- When your iron reaches the required temperature, the selected fabric in the LED screen stops flashing and is displayed constantly Fig 6. You can start ironing. Fig 7-a.
- IMPORTANT The iron takes longer to cool down than to heat up. We recommend that you start with fabrics to be ironed at a low temperature. For mixed fabrics set the temperature for the most delicate fabric.
- On SYNTHETIC mode, the steam is blocked to protect your clothes. For other modes, the iron automatically emits steam when flat. Steam is blocked when the iron is on the heel.
- TIP: Always spray starch onto the reverse side of the fabric to be ironed.
- During the first few uses, you may notice some fumes, a harmless odor, and a slight release of particles. This phenomenon, which does not affect use, will quickly disappear.
Dry ironing
- For dry ironing, select “Synthetic” mode. Ideal for delicates or perfect finishing.
Steam shot
- On linen and cotton mode only, to eradicate the toughest creases, you can activate the shot of steam: press the trigger (1-second max) and release (fig 7-b or below). Wait a few seconds between each shot before pressing the trigger again.
- IMPORTANT Leave an interval of a few seconds between each shot and wait until the flow of steam has finished before placing the iron on its heel.
Anti-Drip system
- It prevents water dripping out of the soleplate when the temperature is too low.
Auto Off function
- For your safety, the electronic system cuts off the power, and the auto-off indicator light flashes Fig 8 when:
- The iron remains motionless for more than 8 minutes on its base
- The iron remains flat or on its side for more than 30 seconds
- To restart the iron, just move it gently until the warning light stops flashing.
AFTER USE Emptying
- Unplug the iron Fig 1. Pour away the remaining water fig 9.
Storing
- Allow the appliance to cool down for 1 hour before winding the cord around the heel. Store the iron on its base in a dry and safe place Fig 11.
- IMPORTANT Do not wind the cord around the hot soleplate. Never store your iron placed down on the soleplate.
- MAINTENANCE AND CLEANING: Remove the plug from the wall socket and let the iron cool down before maintenance and cleaning.
Cleaning the iron
- When the appliance has cooled down, wipe the iron down with a damp cloth or sponge. A nonabrasive cleaning agent can be used.
- IMPORTANT Do not use sharp or abrasive cleaning agents or objects to clean the soleplate and other parts of the iron.
- WARNING: Do not use descaling agents even if advertised for steam irons. They will permanently damage your iron.
Calc clean program (4-6 min)
- The Calc Clean System flushes dirt and scale particles out of the steam chamber.
- This considerably prolongs the operational life of your iron.
- Your iron needs to be cleaned when the CALC CLEAN warning light remains light on the LED screen fig 10a.
- If the “CALC CLEAN” light starts flashing when you are ironing, you can finish your ironing session. There is no risk to your clothes or the appliance.

TO START THE CALC CLEAN PROGRAM:

Unplug the iron (fig 1)
Fill in the water tank Fig 2 & 3
Plug the iron (fig 4)
Put the iron over a sink or a basin
Press the Mode button for 20 seconds to start the Calc Clean Program. (fig 10b)

The iron will start to heat up without producing steam. When arrives at the maximum temperature, the water will start to run down Fig 10c.

During the process, the fabrics on the LED screen will blink alternatively. Once the process is finished, the iron will automatically shut off. Allow the appliance to cool down and then wipe the iron down with a damp cloth or a sponge.

IMPORTANT: This program will last 4 to 6 minutes.

PROBLEMS

Problem	Cause	Solution
The iron is plugged in, but the soleplate of the iron remains cold.	No mains
supply.	Check that the mains plug is properly inserted or try plugging the

iron into a different socket.
The automatic electronic auto-off is active.| Move your iron.
None or too little steam is being emitted.| The iron is not ready to use.| Wait until the mode you have selected stops blinking.

NB: In SYNTHETIC mode, the steam is blocked to protect your clothes.

Not enough water in the water tank.| Fill the water tank.
Anti-Drip is active| Wait for the soleplate to reach the correct temperature.
The steam is blocked on SYNTHETIC mode to protect your clothes| Select a higher mode if needed
Problem| Cause| Solution
---|---|---
Brown streaks come through the holes in the soleplate and stain the fabric.| Residues in the steam chamber or on the soleplate.| Use the Calc Clean Program then clean your iron.
Use of chemical descaling agents, perfumed or scented additives.| Do not add any descaling agents, perfumed, or scented additives to the water in the water tank.

Use the Calc Clean Program and clean your iron if you have used the above.

Fabric fibers have accumulated in the holes of the soleplate and are burning.| Clean the soleplate with a non-metallic sponge.
Your linen is not rinsed sufficiently or you have ironed a new garment before washing it.| Ensure linen is rinsed thoroughly.
Use of starch.| Always spray starch onto the reverse side of the fabric to be ironed and clean your iron soleplate afterwards.
Pure distilled /demineralized or softened water is being used.| Only use untreated tap water or mix half tap water with half distilled/demineralized water.

Use the Calc Clean Program and clean your iron.

Iron is leaking.| Overuse of shot of steam trigger.| Allow more time between each shot.
Use of the shot of steam trigger on SYNTHETIC, SILK, or WOOL modes.| Use only the steam boost on the COTTON and LINEN modes.